Moen 2290 - Manual
A user manual for Moen tub and shower valves covers essential installation, operation, and maintenance procedures. The guide highlights critical safety steps–such as turning off water before disassembly–and provides detailed measurements, component diagrams, and mounting requirements to ensure proper fitting. It also addresses valve configurations (with or without stops), rough-in specifications, and flushing instructions while emphasizing pressure testing and pipe security during installation.
Table of Contents:
- Page 1 – Installation Instructions and Safety for Tub and Shower Valves
- Page 2 – Shower Valve Installation, Rough-in, and Pressure Testing
- Page 3 – Assembly and Installation of Faucet Trim Components
- Page 4 – Correcting Reversed Water Lines and Finish Care
MT620J
MODELS 2290, 2291, 2600, 2700, 5401, 62600, 62700, 72615, 72700
and MODEL SERIES T471, T473, T555, T666, T777 & T888
INSTALLATION INSTRUCTIONS
THESE INSTRUCTIONS MUST BE
LEFT WITH HOMEOWNER
TUB AND SHOWER VALVES
Measurements
These are shown in the drawings. The depth measurement is critical. Use
the front face of the plaster ground as a reference point for the finished
wall position, including tile (2-1/16" [52mm]). The center line of the supply
and discharge piping should be a maximum of 2-3/16" (56mm) and a minimum
of 1-7/16" (37mm) behind the finished wall surface.
Available with three or four port castings, with and without stops.
Connections are either 1/2 inch I.P.S. pipe or 1/2 inch copper sweat connections.
If the Moen Slip Fit spout is used, a 1/2 inch copper drop and lookout may be used.
CAUTION:
Always turn water off before disassembling the valve. Open valve handle to
alleviate water pressure to insure that complete water shut-off has been
accomplished.
Before turning water on during either rough-in or trim-out, make sure that cartridge retainer clip is in place. The
cartridge and retainer clip were properly installed and tested before leaving the factory. Although it is unlikely, it is
nevertheless possible that through the handling of the valve by any number of persons the retainer clip may not be
properly installed. This should be carefully checked at time of rough-in and trim-out. If the retainer clip is not properly
installed, water pressure could force the cartridge out of the casting. Personal injury or water damage to the
premises could result.
HANDLE
COVER
HANDLE
KNOB
WASHER
HANDLE
SCREW
HANDLE
LEVER
HANDLE ASSEMBLY
ADJUSTABLE
TEMPERATURE
LIMIT STOP
ESCUTCHEON
PLASTER
GROUND
CAUTION
USE 1/2"
IRON PIPE
SIZE
MINIMUM
OR 1/2"
TUBING.
SUPPLY
SUPPLY
45"
(1143mm)
48"
(1219mm)
1-1/4"
(32mm)
6' 6"
(1981mm)
32"
(813mm)
FINISHED WALL
LINE
2-1/16"
(52mm)
2-1/16"
(52mm)
TUB FILLER
OR SHOWER
TUB/SHOWER
COMBINATION
FLOOR
15/16"
(24mm)
®
CLIP
EAR
UP
IMPORTANT: SEE FLUSHING
INSTRUCTIONS PAGE 2
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Was this manual helpful?
About this manual
- Brand
- Moen
- Model
- 2290
- Document type
- Manual
- Language(s)
- English
- Pages
- 4
- File size
- 58.5 KB
- Format
Summary
Details on installation measurements, component parts, compatible models, diagrams, and safety precautions for mounting tub and shower valves, emphasizing water shutoff before disassembly.
Instructions for installing and operating shower valves, rough-in procedures for 4-port and 3-port series, flushing methods, and warnings regarding soldering and pressure testing before closing walls.
Steps for disassembling, reassembling, and installing shower and tub spouts, including procedures for handling the stop valve and material compatibility notes for faucet systems.
