Mitsubishi XL7000U- User Manual

Mitsubishi XL7000U

Mitsubishi XL7000U– User Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
Page: / 14

Table of Contents:

  • Page 3 – Control command configuration; Code unique to each control operation.
  • Page 6 – Execution procedure of RS-232C commands via LAN; commands without adding a certification data.
  • Page 8 – Read commands for other information; Use the following commands to obtain other information.
  • Page 9 – Remote control key commands
  • Page 10 – Direct commands; How to set the value; Use the character or ASCII code as shown below to set the value.; Function commands
  • Page 11 – Menu setting commands
  • Page 14 – Password lock commands
Loading the manual

1

LCD Projector
XL7100U

Controlling the projector via RS-232C connection

Contents

1. Introduction ............................................................................................................ 2

1.1 Connection ............................................................................................................................... 2
1.2 Interface ................................................................................................................................... 2

1.2.1 Pin assignment of SERIAL terminal (D-SUB 9-pin) .............................................................................. 2
1.2.2 Communications format ...................................................................................................................... 2

2. Control command configuration ............................................................................ 3
3. Control sequence ................................................................................................... 3
4. Execution procedure of RS-232C commands via LAN .......................................... 6
5. Command list ......................................................................................................... 7

5.1 General control commands ...................................................................................................... 7
5.2 Reading commands ................................................................................................................. 7

5.2.1 Status read commands ........................................................................................................................ 7
5.2.2 Read commands for items in INFORMATION menu ............................................................................ 7
5.2.3 Read commands for other information ................................................................................................ 8

5.3 Remote control key commands ............................................................................................... 9
5.4 Direct commands ................................................................................................................... 10
5.5 Function commands .............................................................................................................. 10
5.6 Menu setting commands ....................................................................................................... 11

5.6.1 IMAGE menu ...................................................................................................................................... 11
5.6.2 INSTALLATION menu ......................................................................................................................... 11
5.6.3 FEATURE menu .................................................................................................................................. 12
5.6.4 SIGNAL menu .................................................................................................................................... 12
5.6.5 NETWORK menu ............................................................................................................................... 13

5.7 Password lock commands ..................................................................................................... 14

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 3 - Control command configuration; Code unique to each control operation.

3 2. Control command configuration The command consists of the address code, function code, data code, ACK/NAK, and end code. The length of the command varies among the functions. Address code Function code Data code ACK/NAK End code ASCII code ‘30h’ ‘30h’ Function Data ‘3Ah’ ‘4Eh’ ‘0Dh’ Character 0...

Page 6 - Execution procedure of RS-232C commands via LAN; commands without adding a certification data.

6 4. Execution procedure of RS-232C commands via LAN • When you use the LAN function, set the STANDBY MODE to STANDARD or LAN. • When you execute RS-232C commands via LAN, check that the CONTROL SYSTEM in the NETWORK menu is set to STANDARD. • You can change the certification password using the NETW...

Page 8 - Read commands for other information; Use the following commands to obtain other information.

8 5.2.3 Read commands for other information Use the following commands to obtain other information. ITEM Function Data (Receive) Character ASCII code Model name vMDL 76h 4Dh 44h 4Ch **************** (within 16 characters) Input source vSOUCE 76h 53h 4Fh 55h 43h 45h r1 r2 v1 v2 d1 d2 Number of remain...

Other Mitsubishi Models