Page 2 - Manual Scope; Contents
2 E This guide contains instructions regarding operation, settings, and similar details.For instructions regarding connection and installation, refer to the included Operation Manual. Manual Scope - Microsoft, Windows and Internet Explorer are registered trademarks of Microsoft Corporation.- HDMI, t...
Page 3 - Basic Operation
3 E Basic Operation 1 2 3 4 5 6 7 8 1. INPUT (Input mode selection) The menu is displayed. Press or to select the input mode, and press to enter. * You can select the input terminal by pressing the input switch of the monitor. Input mode Video Audio PC1 DVI-D *1 PC1 input terminal PC audio input ter...
Page 4 - WIDE
E 4 Basic Operation Switching the screen size Even when the screen size is changed, the display may remain the same depending on the input signal. WIDE PC input Displays image so it fi lls the entire screen. AV input An image with a 4:3 aspect ratio is stretched to fi ll the entire screen. ZOOM 1 ...
Page 5 - Menu Items; Displaying the menu screen; Example of operation; Menu screen display
5 E Menu Items Displaying the menu screen Video and audio adjustment and settings of various functions are enabled. This section describes how to use the menu items. See pages 6 to 8 for details of each menu items. Example of operation (Adjusting CONTRAST in the PICTURE menu) 1. Press MENU to disp...
Page 6 - Menu item details; SCREEN; PICTURE; AUDIO; SETUP
E 6 Menu item details The menu will differ depending on the input mode. SCREEN AUTO (PC3/PC4) The CLOCK, PHASE, H-POS, and V-POS are automatically adjusted.Pressing performs adjustment. Use this automatic adjustment when you use the PC3 input terminal or PC4 input terminals to display a PC screen ...
Page 7 - OPTION
E 7 SCREEN MOTION Residual images are reduced by moving the screen.PATTERN 1 .... The whole screen moves vertically and horizontally. PATTERN 2 .... A black screen spreads from the bottom of the screen and then shrinks to the bottom of the screen. If the monitor is installed in the vertical orientat...
Page 8 - Dual screen display
E 8 Menu Items TIPS • When WHITE BALANCE is set to THRU, BLACK LEVEL, CONTRAST, TINT, COLORS and GAMMA cannot be set. • If COLOR MODE is set to sRGB or VIVID, the following items cannot be set. WHITE BALANCE, PRESET, R-/G-/B-CONTRAST, COPY TO USER, and GAMMA Dual screen display You can display the...
Page 9 - In horizontal orientation; In vertical orientation
E 9 Menu Items Enlarge • You can align several monitors and integrate them into a single large screen to display. • Up to fi ve monitors can be aligned in both the horizontal and vertical directions. • Each monitor displays enlarged views of separated images. (Example)Horizontal direction: 2 monit...
Page 10 - Adjustments for PC screen display; Automatic adjustment; Screen display for adjustment
E 10 Menu Items (5) INPUT Speci fi es the input mode at power-on. When not specifying, the screen at the previous power-off appears.Input modes displayed on “PC1/AV1” depend on DVI SELECT settings.Input modes displayed on “PC2/AV2” depend on HDMI SELECT settings.Input modes displayed on “PC4/AV3” de...
Page 12 - PC connection; Daisy chain connection...; Advanced operation; Communication conditions; Command format
12 E Controlling the Monitor with a PC (RS-232C) You can control this monitor from a PC via RS-232C (COM port) on the PC.You can also connect multiple monitors via a daisy chain by using a PC. By assigning ID numbers to each monitor (see page 13), you can make input mode selection/adjustment or can ...
Page 13 - Response code format; When a command has been executed correctly; When a command has not been executed; If execution of the command is taking some time; Communication interval; ID numbers
E 13 Controlling the Monitor with a PC (RS-232C) Response code format When a command has been executed correctly O K Return code(0D H , 0A H ) A response is returned after a command is executed. * If an ID number has been assigned O K SPC 0 0 1 ID number of responding monitor Space (20 H ) Return ...
Page 14 - Commands for ID control; IDST
E 14 Controlling the Monitor with a PC (RS-232C) Commands for ID control The command examples shown on this page assume the following connection and ID number set up. ID number: 1 ID number: 2 ID number: 3 ID number: 4 IDST ......... A monitor receiving this command sets its own ID number in the p...
Page 16 - RS-232C command table; How to read the command table; Power control/Input mode selection
E 16 RS-232C command table How to read the command table Command: Command fi eld (See page 12.) Direction: W When the “Parameter” is set in the parameter fi eld (see page 12), the command functions as described under “Control/Response Contents”. R The returned value indicated under “Reply” can be ob...
Page 18 - SETUP menu; OPTION menu
E 18 SETUP menu Function Command Direction Parameter Reply Control/Response contents * OSD H-POSITION OSDH WR 0-100 0-100 B OSD V-POSITION OSDV WR 0-100 0-100 SCREEN MOTION SCSV WR 0-4 0-4 0: OFF, 1-4: PATTERN1-4 B MOTION TIME 1 MTIM WR 0-20 0-20 B MOTION TIME 2 PATTERN1 MINT WR 10-990 10-990 Per 10...
Page 21 - Settings to connect to a LAN; To set on the monitor; DHCP CLIENT
21 E Your monitor can be connected to a LAN allowing you to control it from a PC on the LAN. You can also con fi gure the monitor to send e-mail noti fi cation when it has a problem. The connection requires a commercially available LAN cable (UTP cable, Category 5, straight through). Hub LAN termina...
Page 22 - To set from a PC; Set up process; guring the monitor’s LAN settings
22 E 22 To set from a PC When the monitor is connected to a PC, LAN settings can be con fi gured via PC. Set up process (1) Connect your monitor to a PC(2) Specify the PC’s IP address(3) Con fi gure the monitor’s LAN settings (1) Connecting your monitor to a PC Connect a commercially available cro...
Page 23 - Controlling with a PC; Basic operation
23 E 23 5. Click on “LAN SETUP” under NETWORK. 6. Specify the “DHCP CLIENT”, “IP ADDRESS”,etc. DHCP CLIENT If your LAN has a DHCP server and you wish to obtain an address automatically, change this setting to “ON”. To set the address manually, set this to “OFF”. IP ADDRESS If the DHCP CLIENT is set ...
Page 24 - INFORMATION; CONTROL; ADJUSTMENT
24 E 24 INFORMATION Information about this monitor appears. CONTROL You can control the operations corresponding to the buttons ( POWER INPUT SIZE ) on the remote control unit. (See page 3.) TIPS • In standby mode, Power ON is the operation available. ADJUSTMENT You can adjust these settings w...
Page 29 - M E M O
Page 30 - MITSUBISHI Contact Information
North America MESCA (Mitsubishi Electric Sales Canada Inc.) http://www.mitsubishielectric.ca Information Technologies Group, 4299 14th Avenue, Markham, Ontario L3R 0J2, Canada Sales Phone :+1-(905) 475-7728 Fax :+1-(905) 475-7958 E-mail :[email protected] Technical Phone :+1-(905) 475-7728 Fax :+1-(...
