Mitsubishi CP-3800DW- User Manual

Page 3 - Introduction; The symbols shown have the following meanings:; Caution; Cautions for Set-up

Introduction Thank you for purchasing this device. This document explains the handling and operation required to use this printer. Please read this document well before use. ■ About the symbols The symbols shown have the following meanings: Caution Accidents caused by failure to heed the warnings ac...

Page 5 - ME THN ΠAPOYΣA; Mitsubishi Electric Corporation

English Hereby, Mitsubishi Electric Corporation declares that this CP3800DW is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Finnish Mitsubishi Electric Corporation vakuuttaa täten että CP3800DW tyyppinen laite on direktiivin 1999/5/EY oleelliste...

Page 7 - Setting Up the Printer

6 Table of Contents Table of Contents Introduction ················································································································· 2 Cautions for Set-up ···························································································· 2 Table of Contents ...

Page 8 - CAUTION

Setting Up the Printer Setting Up the Printer C C h h e e c c k k i i n n g g t t h h e e C C o o n n t t e e n n t t s s Please check that the printer and all accessories are included in the package. Printer Unit ･ When removing the printer from its package, carrying it, or moving it, be sure to us...

Page 9 - Open Lever

Setting Up the Printer Setting Up the Printer Se Sett t i t n i g ng U Upp th t e he Pr Prin inte t r e r N N a a m m e e s s o o f f C C o o m m p p o o n n e e n n t t s s [Front of Unit] LED ･ Please be careful not to hurt yourself or damage anything on the edges of the printer. Ventilation USB p...

Page 11 - Type; Paper; inside the printer and adversely affect the print quality.

Setting Up the Printer Setting Up the Printer Se Sett t i t n i g ng Up Up th t e he Pr Prin inte terr P P a a p p e e r r a a n n d d R R i i b b b b o o n n Type 8inch Paper Width: 203mm Ribbon Width: 210mm CAUTION ･ Set the paper and ribbon without putting them directly on the work surface. Any d...

Page 12 - Release the Open Lever, and pull out the mechanism unit; Remove the scrap box; Scrap Box; Remove the entire paper cassette unit.

Setting Up the Printer Setting Up the Printer Se Sett t i t n ingg Up Up th thee Pr Prin inte terr S S e e t t t t i i n n g g t t h h e e M M e e d d i i a a 1. Release the Open Lever, and pull out the mechanism unit . Open Lever 2. Open the Paper Release lever. Paper Release Lever 3. Remove the sc...

Page 13 - Install the new roll of paper on the paper holder.; Check for uneven ends; Set the paper holder into the paper cassette.; Seal

Setting Up the Printer Setting Up the Printer Se Sett t i t n ingg Up Up th thee Pr Prin inte terr 5. Install the new roll of paper on the paper holder. When installing it, make sure there are no gaps between the paper and the holder. Make sure the paper is not sticking out. If the end of the roll i...

Page 15 - The printer will not operate without the scrap box.; The printer

Setting Up the Printer Setting Up the Printer Se Sett t i t n ingg Up Up th thee Pr Prin inte terr 9. Turn the paper in the direction of the arrow. When it is advanced enough, the buzzer will beep, and the flashing LED (orange) will go out. It is easier to set if the paper is turned while securing t...

Page 16 - Set here

Setting Up the Printer Setting Up the Printer Se Sett t i t n ingg Up Up th thee Pr Prin inte terr 11. Set the new ribbon into the ribbon cassette. Advance the ribbon in the direction of the arrow, and take up any slack. Set it with the supply side in front. 13.Close the mechanism unit. *When the me...

Page 17 - The flashing LED indicates the printer status; indicates lit, indicates flashing, and blank is not lit

Trouble-shooting Trouble-shooting E E r r r r o o r r D D i i s s p p l l a a y y s s Power Ribbon Paper Error The flashing LED indicates the printer status LED display Status Power Ribbon Paper Error Solution Refer to Paper End *1 ● Put in a new roll of paper P.12 Ribbon End *1 ● Put in a new roll ...

Page 18 - printed areas evenly with scissors.

Trouble-shooting Trouble-shooting Tr T o r u o b uble le-s -sho h o ootitn ingg S S o o l l v v i i n n g g M M e e d d i i a a E E r r r r o o r r s s 1. Pull out the mechanism unit. 2. Remove the ribbon cassette. a. If the paper is jammed: 1. Pull any paper remaining in the printer in the directio...

Page 19 - Cutting the paper; Then follow the methods as for setting the media.

Trouble-shooting Trouble-shooting Tr T o roub uble le--sh s o hoooti t n i g ng 2. Remove the scrap box, and rewind the paper. 3. Cut off any partially printed, wrinkled, or otherwise inferior paper evenly with a pair of scissors, and reset the paper. If wrinkles or partially printed areas are left,...

Page 22 - Wipe off any grime while turning the platen roller.

C C l l e e a a n n i i n n g g P P l l a a t t e e n n R R o o l l l l e e r r If there is an indent on the pictures at a regular interval, or if the back of the picture (white side) is dirty, clean the platen roller. There may be dust, grime, adhesives, etc. from the ribbon or paper on the platen ...

Page 23 - These specifications may be changed without prior notice.

S S p p e e c c i i f f i i c c a a t t i i o o n n s s Model CP3800DW Print type Thermal dye sublimation transfer Print mode High-speed mode High quality mode Resolution 300×300dpi 300×600dpi 8×4 203×102mm 8×5 203×127mm 8×6 203×152mm 8×8 203×203mm 8×10 203×254mm Print size A4 203×297mm 8×12 203×305...

Mitsubishi CP-3800DW- User Manual

Table of Contents:

Summary

Other Mitsubishi Models