Mitsubishi AG-150A-A- User Manual

6 2-3 Setting the Java Execution Environment When using Java Plug-in version 1.6.0_10 or later, make the following environment settings (not required for version 1.6.0_09 or earlier). Note: The setting samples and screenshots used in this manual are those of Java Plug-in version 1.6.0_11. 2-3-1 Disa...

7 3 Performing Operations Text below explains how to connect to the AG-150A and how to make various settings for the AG-150A. Note: If the AG-150A is restarted due to a power interruption etc., wait until the screen on the AG-150A main unit displays the normal operation screen (it takes several minu...

8 3-1-2 Encrypting the communication data and login on the AG-150A AG-150A can encrypt communication data using HTTPS (SSL). When connecting the AG-150A to the LAN that can be accessed by the general public, it is recommended that the following settings be made so that the units are monitored and co...

9 (4) If the security alert has not been disabled, after entering the web address and hitting the Enter (Return) key, a security alert message will alert asking if you want to proceed . This is because the AG-150A uses the self-authentication system. Click [Yes] and proceed. Note: Disable the securi...

10 4 Initial Settings This chapter explains how to set the settings on the AG-150A’s initial settings screen. *Refer to Chapter 5 in the Instruction Book that came with the Centralized Controller AG-150A for how to set the settings after the initial power on. 4-1 Setting the Current Date and Time Cl...

11 4-2 Setting the Basic Information and External Input Functions Display the page needed to perform the AG-150A basic setting by clicking [Initial Settings]-[Basic System] in the setting menu pane. On this page, you perform the basic setting such as the AG-150A unit name, network setting and M-NET ...

12 Expansion Controller system selection buttons 4-2-2 Configuring the System Configuration Settings In the System Configuration Settings menu, set the use or non-use of PAC-YG50ECA Expansion Controller, connection target, M-NET settings, and external input settings. Note: When connecting multiple A...

19 4-3 Group Setting Display the page needed to register the group of air conditioners or general equipment to be connected to the AG-150A and to set the group name by clicking [Initial Settings]-[Groups]. On this page, you perform the basic setting such as the AG-150A unit name, network setting and...

20 (3) To register remote controllers in a group, click on the [Remote Controller Registration] field to display the [Select Unit Addresses] screen, and click on the numbers corresponding to the units to be registered. The ones that are selected will be shown with a yellow-green background. To cance...

21 4-4 Interlocked Setting To interlock the operation of LOSSNAY with the run/stop status of the indoor units, click on [Initial Settings]-[Interlocked LOSSNAY] in the menu to bring up the Interlocked LOSSNAY screen, and enter the interlock conditions. Click [Save Settings] to send setting data to t...

22 4-5 Block Setting By performing block settings, multiples of air conditioner groups can be collectively monitored or operated from the Web or TG-2000A. It also enables energy-save/peak cut controls. Bring up the Block Setting screen by clicking [Initial Settings]-[Blocks] in the menu, and registe...

23 5 Functions 1 5-1 Error mail reports/E-mail communication Click on [Functions 1] – [E-Mail] in the menu to open the [E-mail] window and make necessary settings to perform remote monitoring via mail, using error mail report or the maintenance tool. Click [Save Settings] to send setting data to the...

25 (4) To e-mail an error when an error occurs on general equipment connected to PLC for general equipment, click the PLC Connection button, which appears at the time of selection of "General Equipment", to set the IP address of PLC for general equipment. The row number of the set IP address...

26 5-2 Energy-Save Control and Peak Cut Control Click on [Functions 1] – [Peak Cut] in the menu to bring up the peak cut control screen, and make necessary peak cut settings to use the energy-save or peak cut control function. Click [Save Settings] to send setting data to the AG-150A. Note: Run the ...

27 5-2-1 When Demand Controller Method is used (1) To use Demand Controller Method, before using the PLC Software for demand input or Electric Amount Count Software, click on the PLC initialize button once to initialize the internal memory. Note: Do not initialize the memory after the operation has ...

29 5-2-5 When From external system Method is used (1) When the energy-save level is set to 0 (It is always set to level 0 in an energy-save control method), energy-save control will not be performed for the indoor units that show a greater difference between the set temperature and indoor temperatur...

31 5-3 Settings for measurement To measure the temperature or the amount of electricity, click the [Function1]-[Measurement] in the menu, and open the Measurement screen. Settings for controllers used for measurement can be made. After the settings are made, click [Save Settings] to send setting dat...

32 (6) To receive an e-mail when the temperature or the humidity exceeds a certain value, set the upper/lower limit alarm values (occurrence, recovery). Note: To avoid repeating occurrence and recovery, it is recommended that the difference between the occurrence value and the recovery value is appr...

33 5-3-5 Setting the destination to which an error mail is sent To receive an e-mail when the temperature or the humidity exceeds a certain value, make the error mail sending settings. (1) Select [Out-of-limit alarm] in Type of E-Mail pulldown, and enter the Mail Subject and the E-Mail Address. Note...

35 6 Functions 2 6-1 Limiting the Set Temperature Operating Range Click on [Function2]-[Set Temperature Range Limit] in the menu to open the set temperature range limit screen, and make necessary settings to limit the set temperature operating range of the local remote controller. Each user operatio...

36 6-2 Night Mode (Silent Mode) Schedule Click on [Function2]-[Night Mode Schedule] in the menu to open the night mode schedule screen and make necessary settings to switch the outdoor unit operation mode to the night mode (low-noise operation), and set the night mode time interval. Use this mode wh...

37 6-3 System-Changeover of Y series Click on [Function2]-[Auto-changeover] in the menu to open the auto-changeover screen and make necessary settings to switch the operation mode between cooling and heating automatically of the indoor units connected to the same outdoor unit. Set the change over mo...

38 7 Functions 3 7-1 External Temperature Interlock To use external temperature interlock, click [Function 3] on the menu, and then click [External Temperature Interlock]. Air conditioning group can be set for this control. By setting this control on the air conditioning unit at an entrance, our phy...

39 7-2 Night setback control To use Night setback control (abbreviated to setback control below), click [Functions 3] on the menu, and then click [Setback Control]. Air conditioning group can be set for this control. This control prevents indoor dew by heating automatically when the room temperature...

40 7-3 Interlock control To use Interlock control, click [Functions 3] on the menu, and then click [Interlock control]. Interlock conditions and actions can be set. After the settings are made, click [Save Settings] to send setting data to AG-150A. The interlock control verifies the state changes in...

42 7-3-1 Making the interlock settings Up to 150 interlocking conditions from 1 through 150 can be set as follows. (1) Set the input category and interlocking conditions. Select the equipment for the input category and the interlocking conditions (event) according to Table 7- １ . Table 7- １ Interloc...

45 Note: Temperature setting cannot be made unless the operation mode has been set. Note: If an operation mode is selected that is not available for a group of units that was selected in the output unit type field, the units in the group will not perform any operation. Note: To prevent malfunctions ...

47 7-3-2 Disabling/Enabling the setting for each interlocking condition To exclude an individual group from certain settings being applied to, use the Enable/Disable button. No actions will be taken for the group that is set to “Disable.” 7-3-3 Temporarily disabling the interlocking control To tempo...

48 8 User Setting Click on [User settings] in the menu to open the user setting screen and make necessary user settings to limit available functions of a building manager and to change user names and passwords of maintenance user and building manager. A building manager must change group names when ...

49 Table 7-1 Available Function List Function Content Date and time Current date and time setting Basic system *1 AG-150A network setting, external output setting Group name Group name setting Groups Group structure *1 Connection setting of indoor units, remote controllers, system controllers and ge...

50 9 Registering a License for Optional Function Text below explains how to register a license for optional functions. In the Login screen (see3-1), click [License registration for optional functions] and the License Registration of Optional Functions screen will appear. Please ask the dealer you pu...