Page 3 - Table of Contents
Table of Contents Safety Instructions for Display Monitors........................................................................................ ii Maintenance .............................................................................................................................................
Page 5 - Copyright; Disclaimer; Monitor Information
i Copyright Copyright © 2000 Mitsubish Electric Australia Pty. Ltd All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language or computer language, in any form or by any means, electronic, mechanical, mag...
Page 6 - Safety Instructions for Display Monitors
ii Safety Instructions for Display Monitors 1. The AC plug isolates this equipment from the AC Power supply. 2. Unplug the monitor from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. 3. Slots and openings in the cabinet and the back or...
Page 7 - Maintenance
iii Maintenance ✘ Do not expose the monitor to direct sunlight or heat. ✘ Do not spill liquid onto the monitor. ✘ Do not attempt to open the monitor. You may be hurt by electric shock. For service, call your place of purchase. Opening your monitor may also void warranty. ✘ Do not use your monitor wh...
Page 9 - Introduction; Unpacking the Package; Plug’n Play Compatibility
1 Introduction Unpacking the Package Check following items. If they are missing or damaged, consult your place of purchase immediately. 9 Colour monitor 9 Swivel base 9 User’s manual 9 Power cord Locate the model name and the serial number labeled on the back of your monitor. Write down the related ...
Page 10 - Power Management
2 9 Easy to Use On Screen Display The On-Screen Display (OSD) allows you to adjust all settings simply with on-screen menus. 9 Power Saving Function The power management complies with VESA DPMS standard. When the system is idle (off mode), the monitor automatically cuts its power consumption up to 9...
Page 11 - Getting Started; Installing the Monitor
3 Getting Started Installing the Monitor This monitor is equipped with an autosensing power supply for voltage ranges 100~240V AC, 50~60Hz. To install the monitor : 1. Make sure that the system power is turned off. 2. Please refer to the instructions below to connect the signal cable through D-SUB ....
Page 12 - Connecting through D-SUB signal connector
4 Connecting through D-SUB signal connector 1. Make sure that the system power is turned off. 2. Connect the computer end of the D-SUB cable to the 15-pin output connector on the video board of your computer. ) To connect the monitor to an older type Apple Macintosh through a D-Sub cable, you need t...
Page 13 - A Look at the Control Panel; Adjusting the Monitor
5 Adjusting the Monitor A Look at the Control Panel Ente r Exit 1 2 3 4 5 Adjusting the Monitor You can adjust the monitor with the On-Screen Display (OSD) menus. There are 5 keys for user’s control. They include Exit , , , Enter and Power Switch . The following is the introduction: Panel key introd...
Page 14 - Selecting function and making adjustments
6 Selecting function and making adjustments 1) Contrast hot-key mode 1. Press to enter contrast hot-key mode 2. Press or to adjust the setting. 2) Brightness hot-key mode 1. Press to enter brightness hot-key mode. 2. Press or to adjust the setting. 3) Main menu mode Grouped by functions, the OSD off...
Page 15 - Make adjustments; Enter
7 Make adjustments 1. In Main Menu: Press or to locate the item you desire to change. 2. Press Enter to go into the Sub Menu.
Page 16 - Control functions available in main menu; Contrast; Geometry; Rotation
8 3. Press or to locate the function item. Then press Enter and or to make the adjustment. Hor. Position Enter:Save Exit : Exit Enter:Save Exit : Exit etc Sub menu Function name Scale 75 4. Press Exit to save the setting. 5. Press Exit to return to main menu. Control functions available in main menu...
Page 17 - Colour Adjustment
9 Unbalance : adjusts the pincushion balance if both sides of the display are bowed toward the left or right. Trapezoid : makes the vertical edges of the display parallel. Parallelogram : aligns the top and bottom edges of the image. Top corner : adjusts the edge curvature at the top corners of the ...
Page 18 - Recall geometry preset setting; Manual degaussing function; Adjust; Miscellaneous; De
10 4. Recall geometry preset setting Locate and press Enter to recall the preset settings. The word “Recall” will keep blinking on the screen in the process of recall. This page is also a “status display” that shows current horizontal and vertical frequencies. Please note that the resolution data. I...
Page 19 - Timing Setting; Resolution Maximum
11 ) The on-screen menu will automatically disappear after 20-second’s of inactivity. If changes have been made, the monitor will automatically save them. Timing Setting By making adjustments of your video card settings, you can set the timing and the refresh rate to your preferences. The monitor wi...
Page 20 - Troubleshooting; Chapter 2, Getting Started
12 Troubleshooting and Useful Hints Troubleshooting Make sure that your monitor is properly installed if you encounter any trouble using this product (For hardware installation, see Chapter 2, Getting Started ). If the problems persist, check this chapter for possible solutions. 9 There is no pictur...
Page 21 - Australia; New Zealand
13 Need More Help? If your problems remain after checking this manual, please contact your place of purchase or contact: Australia Visit the Mitsubishi Electric Australia web site at www.mitsubishi-electric.com.au Or contact the Service Department for your state: New South Wales and Australian Capit...
Page 22 - Specifications
14 Specifications Picture Tube Size Type Dot pitch Surface coating 17” (43cm) diagonal FST 0.27mm AG, AR, AS coating Maximum Viewable Size 16” (40.6cm) diagonal Power Supply (Universal) Input voltage Power consumption(Max.) 100~240 V AC, 50~60 Hz (Universal) 100W Max. Resolution 1280 x 1024 Horizont...
