METRObility RADIANCE 10/100MBPS ACCESS OPTICAL NETWORK UNIT - Manual

Radiance 10/100Mbps Access Optical Network Unit 5 the sender. FEF enables the Access Line Card in the central office to detect abreak in the Access ONU’s fiber port receiver. The combination of theseoperations, along with the unit’s remote management feature, enable easydeployment of Ethernet servic...

6 Installation Guide Installation Guide 2 A device that is wired straight through needs one crossover connection: If the cable is straight through crossover the MDI-II to MDI-X switch setting should be X II A device that is wired crossover needs a parallel connection: If the cable is straight throug...

Radiance 10/100Mbps Access Optical Network Unit 7 * DIP switches can also be managed remotely via console commands or through Metrobility’s NetBeacon or WebBeaconmanagement software. Refer to the Command Line Interface Reference Guide, NetBeacon Element Management Software Installation & User Gu...

8 Installation Guide Duplex The DUPLEX switch sets the duplex mode on the copper port whenauto-negotiation is disabled. The copper port operates at full duplexwhen DUPLEX is ON. It operates at half duplex when DUPLEX isOFF. When auto-negotiation is enabled, the DUPLEX switch setting isignored. Auto-...

Radiance 10/100Mbps Access Optical Network Unit 9 3 Link Loss Carry Forward Link Loss Carry Forward (LLCF) is provided as an aid in troubleshoot-ing a remote connection. When LLCF is enabled, loss of the receivesignal at the copper port prevents the fiber port from transmitting anidle signal onto th...

10 Installation Guide TM ACT LK ACT TX RX LK DIS Radiance RA21 LBK DIS II x PWR MAN FD 100 Twisted-Pair InterfaceThe copper port provides a shielded RJ-45 connector that supports amaximum segment length of 100 meters. Use only Category 5 cables. Fiber Optic InterfaceThe unit’s fiber receiver (RX) is...

Radiance 10/100Mbps Access Optical Network Unit 11 4 mentary pairs. That is, a -1X model must always be connected to a -1Y.The -1X units are designed to transmit data at a wavelength of 1550nmand receive at 1310nm. Correspondingly, the -1Y units transmit data at1310nm and receive at 1550nm. Apply Po...

Radiance 10/100Mbps Access Optical Network Unit 13 User Guide This section contains information about the operating features of theRadiance 10/100Mbps Access Optical Network Unit. LED Indicators The Radiance Access Optical Network Unit provides several LEDs on the frontpanel for the visible verifica...

14 User Guide Far End Fault ................................................................................... Enabled (ON)Link Loss Return .......................................................................... Disabled (OFF)Link Loss Carry Forward .................................................

Radiance 10/100Mbps Access Optical Network Unit 15 Disabling a port stops the data flow to and from that port. Although data isneither sent nor received, the disabled port continues to accept, process andtransmit management packets. However, if LLCF is enabled and the oppositeport has no link, manag...

16 User Guide Singlemode Fiber Optic Power Monitors Through software * , you can read the input and output power levels of the singlemode fiber optic port on the Access ONU. Input Power LevelThe accuracy of the input power monitor is ± 1dBm from -28dBm to -12dBm. The accuracy is ± 2dBm from -31dBm t...

Radiance 10/100Mbps Access Optical Network Unit 17 Link Loss Carry Forward (LLCF) * The Access Optical Network Unit incorporates Link Loss Carry Forward as an aid in troubleshooting a remote connection. When LLCF is enabled, the ports donot transmit a link signal until they receive a link signal fro...

Radiance 10/100Mbps Access Optical Network Unit 19 Topology Solutions Radiance R5000 Radiance Acces Optical Network Unit Customer Premises CO/POP SNMP Control Remote Communications Path Status Reporting Configuration Instructions Used Bandwidth = 0

20 User Guide Technical Specifications Data Rate Data Rate ________ 100Mbps half duplex, 200Mbps full duplex (Fast Ethernet) ______________ 10Mbps half duplex, 20Mbps full duplex (Ethernet) Network Connections Twisted-Pair InterfaceConnector __________________________________ Shielded RJ-45, 8-pin j...

Radiance 10/100Mbps Access Optical Network Unit 21 Singlemode F/O Interface — extended long haul distance support (RA21-1J)Connector _____________________________________________________ SCWavelength _______________________________________________ 1550 nmRX Input Sensitivity ________________________...

22 User Guide Product Safety, EMC and Compliance Statements T his equipment complies with the following requirements: • UL • DOC Class B (emissions) • CSA • EN55022 Class B (emissions) • CE • EN55024: 1998 (immunity) • EN60950 (safety) • IEC 825-1 Classification • FCC Part 15, Class B • Class 1 Lase...

Radiance 10/100Mbps Access Optical Network Unit 23 Warranty and Servicing Three-Year Warranty for the Radiance Access Optical Network UnitMetrobility Optical Systems, Inc. warrants that every Radiance Access OpticalUnit will be free from defects in material and workmanship for a period ofTHREE YEARS...