Memorex Tek Partner Universal Remote Control - Manual
Memorex Tek Partner Universal Remote Control – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – are required to repeat steps 2 and 3 again.; SEARCH THROUGH THE LIBRARY; is now ready to
- Page 3 – OPERATING THE TEK PARTNER; NORMAL OPERATION
- Page 4 – SPECIFICATIONS; Power Requirement: 4 AA size batteries, alkaline recommended.; DEVICE CODE LIST; TV Brands
- Page 6 – MITSUBISHI UNIFIED 160
- Page 8 – VCR Brands
- Page 10 – MITSUBISHI UNIFIED 212
- Page 11 – SONY BETA/SONY VHS 122
- Page 12 – Cable Box Brands
- Page 13 – STANDARD COMPONENT 474
- Page 14 – ZENITH DRAKE SATELLITE 514
TEK PARTNER
TM
UNIVERSAL REMOTE CONTROL
USER’S MANUAL
Congratulations! Your TEK PARTNER
TM
Universal Remote Control is a state-of-the-art device which
integrates many different infra-red remote controls. The TEK PARTNER
TM
is pre-programmed at the
factory, but you will need to enter a Device Code for each device to complete the program. Simply enter
correct device codes for your equipment and your TEK PARTNER
TM
is ready to use! A Device Code List
is included in this User’s Manual. The TEK PARTNER
TM
replaces up to 4 separate remote controls to
operate your infra-red controlled televisions (TVs), video cassette recorders (VCRs), and cable boxes
(CBLs).
HOW TO INSTALL THE BATTERIES
Your TEK PARTNER
TM
requires 4 fresh AA-size batteries (alkaline batteries recommended).
1.
Remove the battery cover on the back of your TEK PARTNER
TM
.
2.
Observe the polarity of the batteries and the "+/-" marks inside the battery compartment.
3.
Insert the batteries.
4.
Push the battery cover back in place.
NOTE:
When all batteries are disconnected, the TEK PARTNER
TM
retains its setting only for 15 minutes. Should
you fail to replace new batteries in time, use a stylus or the tip of a pen to reset the unit. The reset button is
located inside the battery compartment.
You may now have to re-program your TEK PARTNER
TM
. See SETTING UP YOUR TEK PARTNER
TM
section.
MAIN FEATURES
SETTING UP YOUR TEK PARTNER
TM
There are 4 Device Modes (TV, VCR, CBL, & AUX) in your TEK PARTNER
TM
. You may setup the TEK
PARTNER
TM
by the following code entering or searching instructions.
Setup by entering DEVICE CODE
Referring to the DEVICE CODE LIST, look up the 3-digit DEVICE CODE which corresponds to the
brands and models of your video equipment. If there is more than one DEVICE CODE listed under your
brand, try the first code with the following instructions:
For example, entering your TV’s code:
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
1. Hold down "PREV CH" and "ENTER" together for approximately 4 seconds until the status indicator (located to the left of the "1" button) lights up. 2. Press a desired Device Mode Button (e.g. "TV"). 3. Use the number buttons to enter your 3-digit Device Code (from t...
NOTES: TV, VCR, and CBL Device Codes can be searched and locked into "CBL" & "AUX" modes. Simply press "CBL" or "AUX" Device Mode Button in step 2 and enter an appropriate Magic Search Code to start searching. Each time you press the "VOL+" button, the TEK...
A. Make sure you have pressed the Device Mode Button before using any functions. Q . If several Device Codes are listed for my device, how can I select the correct Device Code? A. To seek the Device Code for your device, test the codes one by one until the buttons work properly. Q . My equipment res...
