McIntosh MC206 - Manual - manualsarea.com

Page 2 - IMPORTANT SAFETY

2 IMPORTANT SAFETY INSTRUCTIONS! PLEASE READ THEM BEFORE OPERATING THIS EQUIPMENT. WARNING - TO REDUCE RISK OF FIRE OR ELECTRICAL SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. The lightning flash with arrowhead, within an equilateral triangle, is intended to alert the user to the presence...

Page 4 - Power Output; Table of Contents; Multi-Channel Amp DB25 Connector Pin Layout

4 Performance Features Introduction and Performance Features Introduction · Power Output The MC206 consists of six Power Amplifier Channels, each capable of 200 watts into 4 ohm or 120 watts into 8 ohm loudspeakers with less than 0.005% distortion. · High Current Output A peak output current of 25 a...

Page 5 - The following dimensions can assist in determining the; Dimensions; Front View of the MC206

5 Dimensions The following dimensions can assist in determining the best location for your MC206. There is additional informa- tion on the next page pertaining to installing the MC206 into cabinets. Dimensions 17- 1/2 " 44.45cm 6 - 5/16 " 16.03cm 7 - 5/8 " 19.37cm 18- 1/2 " 46.99cm 3...

Page 6 - Custom Cabinet Cutout; in Custom Cabinet

6 Installation The MC206 can be placed upright on a table or shelf, standing on its four feet. It also can be custom installed in a piece of furniture or cabinet of your choice. The four feet may be removed from the bottom of the MC206 when it is custom installed as outlined below. The four feet tog...

Page 7 - Rear Panel Connections and Switch

7 Rear Panel Connections and Switch Connect the MC206 power cord to a live AC outlet. Refer to informa- tion on the back panel to determine the correct voltage MULTI-CHANNEL INPUT accepts a 25 conductor DB25 computer type cable that con- nects all audio and power con- trol signals POWER CONTROL IN r...

Page 8 - How to Connect the MC206 for Six Channels

8 Caution: The supplied AC Power Cord should not be connected to the Rear Panel of the MC206 Amplifier until after the Loudspeaker Connections have been made and the supplied protective Terminal Connection Covers have been installed. Failure to observe this could result in Electric Shock. 1. Connect...

Page 10 - Front Panel Displays and Controls

10 Front Panel Displays and Controls Remote On Indicator lights when the amplifier is in the Remote Turn-On Mode POWER GUARD LEDs light when the LEFT FRONT, or LEFT SURRound Amplifier Channel POWER GUARD Circuit activates METER LEDs indicate the Power Output Meter is display- ing the LEFT FRONT and/...

Page 11 - Power On; How to Read the Power Output Meters; XPPHG&KDQQHOV0HWHU5HDGLQJV

11 How to Operate and Read the Power Output Meters How to Operate Power On To have the MC206 turn On or Off when a A/V Control Center turns On or Off, rotate the POWER Switch to the REMOTE Position. For manual operation, rotate the POWER Switch to the ON or OFF Position as de- sired. Refer to figure...

Page 12 - LQJOH&KDQQHO0HWHU5HDGLQJV; CAUTION: When the MC206 amplifier is used in specific

12 6LQJOH&KDQQHO0HWHU5HDGLQJV 0HWHU5HDGLQJ 2KP /RXGVSHDNHUV 2KP/RXGVSHDNHUV :DWWV :DWWV :DWWV :DWWV :DWWV :DWWV :DWWV :DWWV :DWWV :DWWV CAUTION: When the MC206 amplifier is used in specific Countries (Austria, Belgium, Germany, Denmark, Spain, Finland, France, United Kingdom, Greece, Ireland, It...

Page 13 - Notes

Page 14 - Note: Refer to the rear panel of the MC206 for the correct

14 Specifications Specifications Power Output Minimum sine wave continuous average power output per channel, all channels operating is: 200 watts into a 4 ohm load 120 watts into a 8 ohm load Rated Power Band 20Hz to 20,000Hz Total Harmonic Distortion Maximum Total Harmonic Distortion at any power l...

Page 16 - Chambers Street

McIntosh Part No. 040752 McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, NY 13903