Maytag MDE 1100AES - Manual

6 1 2 Control panel 1. Temperature setting 2. Timer

7 595 mm 640 mm 1730 mm 610 mm Where to install it  If the drying cabinet is to be installed with a connection to exhaust air ventilation, this must be available on the premises. See futher section “Ventilation alterna- tives”, page 9 .  A grounded electrical outlet must be within 79 in. (2 meters...

8 Electrical requirements Electrical connection  The drying cabinet must be connected to a 230 Volt single-phase 50 Hz grounded wall outlet. The electric outlet must be installed and grounded in accordance with regulations in force.  The drying cabinet is delivered complete with connections, inclu...

9 1 2 1 2 Ventilation alternatives Minimum 300 mm Ceiling  Do not hesitate to open doors or windows in the room for optimum ventilation.  In the case of an inbuilt drying cabinet, exchange the flexible ventilation hose delivered with the cabinet (only certain markets) for a rigid ventilation pipe o...

10 1 2 3 4 5 6 Connection to a vent duct T h e d r y i n g c a b i n e t m u s t n o t b e connected to the fireplace chimney ATTENTION When the cabinet is on, 45 m³ of humid air are evacuated per hour. So make sure that air can penetrate into the room to replace the humid air given off by the drying...

12 Installation  Take off all the packing material; do not use a sharp tool which could damage the product.  Check that the drying cabinet has not been damaged during transportation. The distributor should be notified of any damage during transportation within 7 days. The cabinet can easily tip ove...

13 1 2 The door can be hung on its hinges on the left or the right. 1. Lay the drying cabinet on its back side. 2. Disengage the hinge pin of the bottom hinge (1) and lift the door off. 3. Take off the plastic plug and press it right down on to the bottom hinge on the opposite side. 4. Disengage the...

14 ������ 2 3 1 2 1 Horizontal adjustment 1. Lift out the shoe rack. 2. Control that surfaces are horizontal by placing a bubble level parallel to the walls and parallel to the back and the door. 3. Use the Allen wrench provided, and cor- rect the position of all four adjustable feet through the hol...

15 1 2 3 4 5 1. Keep the adhesive tape on the door until the drying cabinet is in place. Place the cabinet so that its front is properly aligned with the cabinetry facing. 2. Plug the connection cord into the socket and take care to be sure that the cord is not stuck and can easily be unplugged. 3. ...

17 1 Ventilation connection If the drying cabinet is installed in a custom cabinetry, fit the exhaust collar through the vent opening in the upper part of the cabinetry when the drying cabinet is moved to its final location. 1. Place the exhaust collar over the hole in the drying cabinet’s top plate, ...

18 1. Check that all parts are mounted. If not - go through all the steps once more. 2. Check that no packing material is left lying around. 3. Use a mild washing up product with warm water and wash the drying cabinet inside and out. Dry it carefully. See also the sec-tion ’Care’ further on in the m...

19 How to use the drying cabinet Starting 1. Place the articles to be dried in the drying cabinet and shut the door. See also the section ”Loading”. 2. Set an appropriate temperature and drying time. See the section ’Setting the tempe-rature selector knob’. Stopping Open the door and turn the time s...

20 Some advice for users Setting the controls  Set the temperature and the time selec- tor knobs for the most delicate articles to be dried.  The temperature is changed by means of the temperature selector knob which can be turned in both directions. Drying  Always follow the washing instructions...

21 1 3 2 ����� ���� ��� ��� � ��� ���� ����� ��� ����������� ����������� ���� ���������� ������� � � � � � � � � � � � � � � � � Setting the temperature selector knob Setting Type of fabric Temperature 1 Foam rubber products, plastic, clothes which are sensitive to heat Fan only 2 Sportswear, underw...

22 Care When the drying cabinet is not in use Cleaning the drying cabinet High-pressure cleaning should not be used!  The walls of the cabinet should be clea- ned with a mild soap solution on a damp cloth.  Dust frequently gathers round the air intake orifice on the upper part of the cabinet. This ...

23 Trouble Shooting Before calling on outside help, first try to put the trouble right with the help of the indications below. Trouble Cause What to do Garments are not b e i n g d r i e d a s expected  The fuses controlling the drying cabinet have tripped.  The temperature and/or time se- lector k...

24 DC XXXX ��������������������� ���������������� ���������������� 1 2 3 4 5 Service Before you contact customer service , you should find out the designation of the model, its type and its serial number.The designation of the model is inscribed on the cabinet control panel. The type and the serial n...

25 Technical information *) Given values may vary depending on the rotation speed during spin-drying Air gap left during mounting Minimum 10 mm between drying cabinet and custom cabinetry (above and behind the drying cabinet). Evacuation/Air intake When the cabinet is on, 45 m³ of humid air are evac...