Matrix Decor MDF6223110V - User Manual

Installation & Operating Instructions for the

F6208

Parrotuncle Owner’s Installation ,Manual

WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER

Parrotuncle Lighting, 218 Black Tie Lane, Chapel Hill, NC

www.parrotuncle.com

Parrot Uncle YOU CAN BE SURE OF are trademarks of Eileen Grays LLC.

Used under license by Eileen Grays LLC.

Made in China

SKU

Rated Voltage

Light CCT.

Rated power(motor)

.

110-120 VAC

3000K

F6208

55W

THANK YOU FOR YOUR PURCHASE

Thank you for purchasing this quality product. To ensure correct function and safety, please read and save all

instructions before using the product

1. Mounting bracket

2. Mounting screws

3. Canopy & decorative

canopy cover

4. Downrod & hanger ball

5. Bolt

6. Lock pin

7. Coupling cover

8. Fan motor assembly

9. Center flywheel

10. Blades

11. Light pan

12. Screws for light shade

13. Light shade

14. Wood screws

15. Expansion screws

16. Screw washers

17. Balancing tape

18. Balancing clip

19. Remote control set.

BEFORE INSTALLATION

Unpack your fan and check the contents.You should have the following:

CAUTION

READ INSTRUCTIONS CAREFULLY FOR SAFE

INSTALLATION AND FAN OPERATION. IF UNSURE CONSULT

A QUALIFIED ELECTRICIAN

SAFETY TIP

1.

To avoid possible electric shock, turn off the electricity at the main fuse box or circuit panel before you begin

the fan installation or before servicing the fan or installing accessories.

2. Read all instructions and safety information carefully before installing your fan and save these instructions.

3. Make sure all electrical connections comply with local codes or ordinances and the National Electrical Code.

If you are unfamiliar with electric wiring, please use a qualified and licensed electrician.

4. Make sure you have a location selected for your fan that allow clear space for the blades to rotate, and at least

seven (7) feet of clearance between the floor and the fan blade tips. The fan should be mounted at least thirty

(30) inches from walls or other upright structures.

5. WARNING: The outlet box and ceiling support joist used must be securely mounted, and capable of

supporting at least 100 pounds. To reduce the risk of fire, electric shock or personal injury, mount to the outlet

box marked acceptable for fan supported and use mounting screws provided with the outlet box. The box must

be supported directly by the building structure.

6. WARNING: To reduce the risk of fire, electric shock or personal injury, mount to outlet box marked

“acceptable for fan support” and use mounting screws provided with the outlet box most outlet boxes commonly

used for the support of lighting fixtures are not acceptable for fan support and may need to be replaced. Consult

a qualified electrician if in doubt.

7. Electrical diagrams are for reference only. Light kits that are not packed with the fan must UL listed and

marked suitable for use with the model fan you are installing. Switches must be UL. general use switches. Refer

to the instructions packaged with the light kits and switches for proper assembly.

8. After installation is complete, check that all connections are absolutely secure.

9. After making electrical connections, spliced conductors should be turned upward and pushed carefully up

into outlet box. The wires should be spread apart with the grounded conductor and the equipment-grounding

conductor on one side of the outlet box.

10. WARNING: To reduce the risk of electrical shock and fire, do not use this fan with any solid-state fan speed

control device, or rheostat.

11. Do not separate the reverse switch until the fan has come to a complete stop.

12. Do not insert anything into the fan blades while they are rotating.

13. WARNING: To reduce the risk of personal injury, do not bend the blade brackets (also referred to as

“flanges”) during assembly or after installation. Do not insert objects in the path of the blades.

14. To avoid personal injury or damage to the fan and other items, be cautious when working around or cleaning

the fan.

15. Do not use water or detergent when cleaning the fan or fan blades. A dry dust cloth or lightly dampened

cloth will be suitable for most cleaning.

NOTE: The important safety precautions and instructions appearing in the manual are not meant to cover all

possible conditions and situations that may occur. It must be understood that common sense and caution are

necessary factors in the installation and operation of this fan.

All rights reserved.

NOTE: This product is not intended for use by persons (including children) with reduced physical,

sensory or mental capabilities are different or are impaired, or lack of experience or knowledge,

unless such persons are supervised or trained to operate the appliance by a person responsible for

their safety.

NOTE: Children should be supervised to ensure that they do not use appliances as a toy.

BEFORE INSTALLATION

INSTALLING THE FAN

Tools Required: Phillips screwdriver, Pair of pliers, straight slot screwdriver, adjustable wrench, step ladder, and wire cutters.

INSTALLLING THE MOUNTING BRACKET

The ceiling fan must be installed in a location so that the blades are 12”( 300mm) spacing from the tip of the blade to the nearest objects or walls. When hanging the Fan REMEMBER to turn off the

power. Follow the instruction below to hang your fan properly:

NOTE:Hanger after the installation must be able to withstand the weight of 100lbs( 45kgs) or more

1. For concrete ceiling, drill two holes in

the ceiling and secure the mounting

bracket to the ceiling with two

Φ

0.32”(8mm)

（

distance between the

two holes should be appropriate

）

expansion screws, flat washers,nuts

provided and tighten with a spanner.

2. For wood ceiling, install the

mounting bracket to the ceiling which

is capable of carrying a load of at least

100lbs(45kgs) with two long mounting

screws and washers provided. Be sure

at least 0.12”(30mm) of the screw is

threaded into the support.

3. For installing to outlet box, secure the outlet box

directly to the building structure. Use appropriate

fasterners and building materials. The outlet box and its

support must be able to fully support the moving weight

of the fan(at least 100lbs). Use a UL listed metal outlet

box. Do not use a plastic outlet box. Figure 1& 2

examples to mount the outlet box.

4. Refer to the Fig. in right for mounting

when the ceiling is angled max. 15

degree angle.