Marantz TT-15S1 - User Manual

3 ACCESSORIES Before using the turntable, please make sure that you have all of the following accessories. 1. Turntable chassis 2. Center shaft 3. Tone arm 4. Turntable 5. Motor 6. Motor pulley (for 60Hz areas) 7. Gloves (pair) 8. Ground wire

4 ACCESSORIES 9. 2 Drive belts (1 spare belt) 10. Bearing oil 11. Turntable sheet 12. 3 Allen wrenches (large/medium/small) 1 adjustment screwdriver 13. Record clamp (“Clever clamp” produced by Southern Engineering) 14. Counter weight 15. Tone arm height adjustment sheet 16. Cartridge (MM type) by C...

5 ASSEMBLING AND ADJUSTING 1. Installing the ground wire Connect the ground wire to the turntable shaft base. 2. Inserting the center shaft Insert the center shaft into the turntable chassis. 3. Installing the turntable Place the turntable onto the center shaft. 4. Attaching the tone arm a) Pass the...

6 ASSEMBLING AND ADJUSTING b-2) Direction The direction position is correct when the tone arm isparallel with the side of the turntable base. b-3) When you have determined the height and direction of the tone arm attachment position, tighten the tone armfixing screw using the Allen wrench (large). A...

7 ASSEMBLING AND ADJUSTING c) Attach the cartridge that you attached in the previousstep to the tone arm. • When using the included cartridge Attach to the front attachment hole position on the tonearm. • When using a different cartridge Attach the cartridge so that it is 32mm from the stylustip. d)...

8 ASSEMBLING AND ADJUSTING d) Lower the lifter lever, and rotate the counter weight tobalance the tone arm so that it is parallel with theturntable. e) After finding the balance, raise the lifter lever and attachthe anti-skating adjustment screw. 7. Stylus pressure adjustment A d j u s t t o t h e r...

9 ASSEMBLING AND ADJUSTING 9. Attaching the motor pulley Attach the motor pulley to the motor. Using the adjustment screwdriver included to fix thepulley’s 3 plastic screws. Be careful not to turn the screws with too much force,as they are made from plastic and can break easily. When attaching the p...

10 NAMES AND FUNCTIONS q Power switch (OFF, ON) When it is switched ON, the turntable rotates. w Pulley This is changed to suit the rpm speed of the record to beplayed. 33 1/3 rpm record ....................................[Lower side]45 rpm record ..........................................[Upper si...

11 CONNECTIONS AND OPERATION 7 Connections Make sure that the power supply to both this turntable and the amplifier are OFF before you start connecting. 1. Connect the PHONO cables (L: white, R: red) that areconnected to the toner arm to the corresponding L andR [PHONO] input terminals on your ampli...

12 TROUBLE SHOOTING If you think a malfunction has occurred, first check the points listed below. 7 Are each of the connections correct? 7 Are you operating the turntable correctlyas described in this instruction manual? If the turntable does not operate correctly, check all of the items in the foll...

13 SPECIFICATIONS AND EXTERNAL DIMENSIONS DIAGRAM 7 Turntable section RPM ................................................33 1/3 rpm, 45 rpm Drive system ..........................................Belt drive system Turntable ............................................High density acrylic Turntable d...

14 The section describes the care and maintenance tasks thatm u s t b e p e r f o r m e d t o o p t i m i z e t h e o p e r a t i o n o f y o u rMarantz equipment. 7 Cleaning external surfaces ofequipment The exterior finish of your unit will last indefinitely withproper care and cleaning, Never use...

www.marantz.com You can find your nearest Marantz Authorized Dealer on our website. U.S.A. Marantz America, Inc. 1100 Maplewood Drive, Itasca, IL 60143, U.S.A. Printed in USA 11/2005 00M31BW851250 mzh-d is a registered trademark.