Marantz PM10S1GD - User Manual

Part names and functions Front panel . u i o e q y t r w w A Input source select knob (INPUT SELECTOR) This selects the input source. ( v p. 17) B Illumination lamp The illumination lamp lights (blue). C Display This displays various pieces of information. D Power indicator This is lit as follows ac...

Rear panel . e w q t y u i o Q0 r A Analog audio input connectors (AUDIO IN) Used to connect devices equipped with analog audio output connectors. 0 “Connecting a playback device” ( v p. 10) 0 “Connecting a recording device” ( v p. 10) B AUDIO OUT connectors (RECORDER) Used to connect the input conn...

Remote control unit n Operating this unit To operate amplifier, press REMOTE MODE AMP button to switch the remote control to the amplifier operation mode. . r o u Q0 e t q i w y A Cursor buttons ( uio p ) These select items. B DISPLAY button This turns the display on/off. Press and hold to turn the ...

n CD player operations The supplied remote control can be used to control a Marantz CD player in addition to this unit. To operate a Marantz CD player, press the REMOTE MODE CD button to switch the remote control to the CD player operation mode. . q wer t ui o Q0 Q1 y Q7 Q9 Q8 Q3 Q5 Q6 Q2 Q4 A Power...

Connections n Contents Connecting speakers 8 Connecting a playback device 10 Connecting a recording device 10 F.C.B.S. connection 11 Connecting a pre-amplifier 15 Connecting devices with remote control connectors 16 Connecting the power cord 16 NOTE 0 Do not plug in the power cord until all connecti...

Speaker connection This unit is equipped with two sets of speaker terminals (SPEAKER A and SPEAKER B). One set of speakers can be connected to each set of terminals, and a total of two sets of speakers can be connected.The same signal is output from the SPEAKERS A and SPEAKERS B terminals.When only ...

Connecting a playback device You can connect turntables, tuners, CD players and network audio players to this unit.Set the phono equalizer of this unit in the "PHONO" section of the setting menu according to the type of turntable cartridge to be connected. ( v p. 21) If you set this unit’s i...

F.C.B.S. connection The Marantz F.C.B.S. (Floating Control Bus System) is the high quality sound system for link control between multiple PM-10 units (up to 4 units). Each unit is controlled via its ID number registered beforehand.The ID numbers need to be set to an operating unit (master) and a sub...

n How to set ID number for F.C.B.S. When the unit is turned on, the display shows the ID number for three seconds.For a master unit, ID number 1 needs to be assigned.For a slave unit, set any of ID numbers 2 to 4. . INPUT SELECTOR X F.C.B.S. ID 1 While holding F.C.B.S. ID on the rear panel,press X ....

Connection for 5.1 Multi-channel Playback The three units are connected using F.C.B.S. For the F.C.B.S connection, prepare 3 audio connection cables, and refer to F.C.B.S.. ( v p. 11) Connect the outputs of players that have 5.1 channel analog outputs to each of the three units.If using an active su...

n Speaker Positioning for Super Audio Multi-channel Sound In order to enjoy Super Audio CD multi-channel sound with the best possible acoustics, it is recommended to position speakers as specified in ITU-R BS.775-1 of the International Telecommunication Union (ITU). Super Audio CD multichannel discs...

Connecting devices with remote control connectors Performing operations by RC on this unit without visual contact You can connect an external IR receiver to the REMOTE CONTROL connectors to perform operations on this unit with the supplied remote control unit without visual contact. This might be ne...

Playback n Contents Turning the power on 17 Selecting the input source 17 Adjusting the volume 17 Turning off the sound temporarily (Muting) 18 Adjusting the left and right channel balance 18 Having the display and the illumination lamp off 18 Having the illumination lamp always off 18 Playing CDs 1...

Turning off the sound temporarily (Muting) 1 Press MUTE. “ATT” appears on the display and the sound is muted. 0 To cancel mute, press MUTE again. n Setting the attenuation level when sound is muted The attenuation level can be set at –20 dB, –40 dB, or –∞. 0 The factory default setting is –∞. 1 Pres...

Playing CDs This section uses playback from a CD as an example. 1 Press X on this unit to turn the power on. 2 Use INPUT df to switch the input source to “CD”. “CD” is displayed on the display of this unit. 3 Playback the CD. 4 Use VOLUME df to adjust the volume. Recording Audio signals input into t...

Settings Menu map By default, this unit has recommended settings defined. You can customize this unit based on your existing system and your preferences. Setting items Description Page PUREST Sets PUREST mode, the mode with the highest sound quality. This mode restricts noise that may affect sound q...

PUREST Noise sources that influence sound quality can be suppressed in order to achieve higher quality playback by stopping all of the following circuits. 0 Recording output circuit 0 Non-signal state detection circuit 0 Headphones circuit ON: Enables the high sound quality mode (PUREST mode). OFF (...

Tips n Contents Tips I want to adjust the attenuation level when muting sound 23 I want to turn the illumination lamps on both sides of the unit main panel off 23 I want to use two or more of these units for high quality playback 23 I want to use this unit’s remote control to operate a Marantz CD pl...

Tips I want to adjust the attenuation level when muting sound 0 The attenuation level can be set at –20 dB, –40 dB, or –∞. ( v p. 18) I want to turn the illumination lamps on both sides of the unit main panel off 0 Turn the illumination lamp setting off. ( v p. 18) I want to use two or more of these...

Troubleshooting If a problem should arise, first check the following: 1. Are the connections correct? 2. Is the set being operated as described in the owner’s manual? 3. Are the other devices operating properly? If this unit does not operate properly, check the corresponding symptoms in this section...

n Operations cannot be performed through the remote control unit Symptom Cause / Solution Page Operations cannot be performed through the remote control unit. 0 Batteries are worn out. Replace with new batteries. 2 0 Operate the remote control unit within a distance of about 23 ft/7 m from this unit...

n Desired sound does not come out Symptom Cause / Solution Page No sound comes out of a specific speaker. 0 Check that speaker cables are properly connected. 8 0 Adjust the left and right channel balance. 18 The left and right of stereo sound is reversed. 0 Check whether the left and right speakers ...

Appendix Explanation of terms MM/MC cartridge There are two types--MM (Moving Magnet) and MC (Moving Coil)--of cartridges for turntable. As the output levels for these two types of cartridges differ, the setting of the phono equalizer that is mounted in this unit must be switched according to the ty...

Specifications 0 RMS Power output (Simultaneous drive of both channels) : 200 W x 2 (8 Ω/ohms load, 1 kHz, T.H.D. 0.05 %)400 W x 2 (4 Ω/ohms load, 1 kHz, T.H.D. 0.1 %) 0 Total harmonic distortion (1 kHz, simultaneous drive of both channels, 100 W, 8 Ω/ohms load) : 0.005 % 0 Frequency response (CD, 1...

n Dimensions (Unit : in. (mm)) . 17 3/8 (440) 3/4 (18) 1/4 (4) 5 3/4 (146) 6 5/8 (168) 12 (302) 15 3/4 (400) 17 7/8 (453) 3/4 (19) 1 3/8 (34) 10 1/2 (266) 2 5/8 (66) 2 3/4 (68) 2 3/4 (69) 2 3/4 (69) 2 3/4 (67) n Weight : 46 lb 15 oz (21.3 kg) ENGLISH 29 Printing : Color : Black

Index v A Auto Standby mode ............................................................. 21 v B Bi-wiring ................................................................................ 9 v C CD player ...................................................................... 10, 19 v D Display bright...