Page 2 - Safety Notices; When installing or using the AuCS; WARNING; Procedural Notices; When installing or using the Model AuCS; Important; Important boxes serve two functions:; CAUTION
Safety Notices When installing or using the AuCS ® A accessory, be sure to pay close attention to the safety notices in this manual. Disregarding the notices may lead to serious injury and/or damage to the ice machine or AuCS ® accessory. Throughout this manual, you will see the following types of s...
Page 3 - Table of Contents; Section 1 - General Information
Table of Contents i Table of Contents Section 1 - General Information Freight Damage and Claims Procedure......................................................................................................... 1-1 Model/Serial Number Location ...........................................................
Page 4 - THIS PAGE INTENTIONALLY LEFT BLANK
Table of Contents ii THIS PAGE INTENTIONALLY LEFT BLANK
Page 5 - Section 1; Freight Damage and Claims; Model/Serial Number Location
Section 1 General Information 1-1 Section 1 General Information Freight Damage and Claims Procedures 1. Shortages Check the number of cartons delivered against the quantity shown on your receipt. If the quantities do not match, have the driver note the shortage and file your claim with the freight c...
Page 6 - Owner Warranty Registration Card; Warranty Coverage
General Information Section 1 1-2 Owner Warranty Registration Card GENERAL The packet containing this manual also includes warranty information. Warranty coverage begins the day your new AuCS ® A accessory is installed. Important Complete and mail the OWNER WARRANTY REGISTRATION CARD as soon as poss...
Page 7 - Component Location and Identification
Section 1 General Information 1-3 Component Location and Identification MOUNTING SLOTS SV3065 RELAY COMMUNICATION CONNECTION QDUAL COMMUNICATION WIRE IS SUPPLIED WITH ICE MACHINE AND IS LOCATED ON THE BACK OF THE CONTROL BOX CLEANING FREQUENCY SELECTOR SWITCH ELECTRIC CORD TO DISPENSING PUMP CONTROL...
Page 8 - Compatible Ice Machine Models; The AuCS; Air, Water or Remote Condenser
General Information Section 1 1-4 Compatible Ice Machine Models The AuCS ® A accessory can be used on all Manitowoc ice machines capable of accepting the AuCS accessory. Q Model Undercounter (Q130, Q210, Q270) QM model (QM20, QM30, QM45) and Flake Ice Machines (QF800, QC700, QF400) are not AuCS comp...
Page 9 - Section 2; General; Electrical Service; Phase; power cord, have an outlet
Section 2 Installation Instructions 2-1 Section 2 Installation Instructions General These instructions are provided to assist the qualified installer. Check your local yellow pages for the name of the nearest Manitowoc Ice Machine Distributor or call Manitowoc Ice, Inc. for information regarding ins...
Page 11 - Height and Distance Requirements
Section 2 Installation Instructions 2-3 BASE OF ICE MACHINE Height and Distance Requirements SV1639G NO! TOO HIGH 2” 5 CM 2” 5 CM BOX BASE OR BOX TOP MUST BE WITHIN 2” (5 CM) OF ICE MACHINE BASE NO! TOO LOW NOTE: BOX MUST ALSO MOUNT WITHIN REACH OF 9’ TUBING AND LOW VOLTAGE COMMUNICATION WIRE.
Page 12 - Connection to Ice Machine; GENERAL; A and; right side panels from the ice machine.
Installation Instructions Section 2 2-4 Connection to Ice Machine GENERAL Parts Identification PVC CONDUIT FITTING (A) INSTALLATION ½” PVC CONDUIT FITTING A ½” LOCKNUT (C) ½” PVC CONDUIT FITTING (A) B HOSE CLAMPS LOCKNUT C SV1636G BUMPER D PVC Conduit Fitting (A) Installation 1. Insert the PVC fitti...
Page 14 - QDUAL
Installation Instructions Section 2 2-6 IB600C IB800C IB1000C Q1400C 1-1/8" DIAMETER ACCESS HOLE 1-1/8" DIAMETER ACCESS HOLE 5.9" 7.5" 2" 3.0" QDUAL 1-1/8" DIAMETER ACCESS HOLE 7.5" 2"
Page 15 - Connect the 1⁄2” PVC conduit from the AuCS; Typical PVC Conduit Installation
Section 2 Installation Instructions 2-7 Connection to Ice Machine (cont.) PVC CONDUIT CONNECTION (NOT SUPPLIED) Connect the ½” PVC conduit from the AuCS ® A to the ice machine. CAUTION Install 1/2” conduit to protect the tubing and modular wire from damage or access. NOTE: A pulling elbow is recomme...
Page 16 - Vinyl Tubing Installation
Installation Instructions Section 2 2-8 Connection to Ice Machine (cont.) WATER INLET VALVE ACCESS HOLE SV1641G WATER INLET BARBED FITTING WATER INLET BARBED FITTING Vinyl Tubing Installation (Typical 22” Ice Machine Shown) SV3064 IB600C IB800C IB1000C ROUTE TUBING ROUTE TUBING AND CONNECT TO 90 ° E...
Page 17 - threaded
Section 2 Installation Instructions 2-9 Q1400C ONLY A. 1/4" DIA x 4" LG VINYL TUBING B. 1/2" PVC CONDUIT FITTING (QTY 2) C. 90 ° THREADED ELBOW D. 1/4" FERRULE NUT E. 90 ° BARBED ELBOW F. 3/8" HOSE CLAMP (QTY 2) G. 1/2" LOCKNUT (QTY 2) A. Slide the 1/4" ferrule nut (part ...
Page 18 - COMMUNICATION WIRE CONNECTION; A to the ice; Low Voltage Communication Wire Connection; is
Section 2 2-10 Installation Instructions Connection to Ice Machine (cont.) COMMUNICATION WIRE CONNECTION Insert the low voltage communication wire through the ½” conduit connecting the AuCS ® A to the ice machine. A to the ice machine. Plug into the jacks on the ice machine control board and the AuC...
Page 19 - VINYL TUBING CONNECTION; Connecting Vinyl Tubing to; Water Inlet Barbed Fitting
Section 2 Installation Instructions 2-11 Connection to Ice Machine (cont.) VINYL TUBING CONNECTION 1. Insert the tubing into the ½” conduit from the AuCS ® to the ice machine. 2. Slide the 3/8” hose clamp (B) onto the tubing and connect it to the barbed fitting on the AuCS ® dispenser pump. Connecti...
Page 20 - Determine Type Of Solution Needed; Model; Installing Bottle Of Solution; Bottle Installation
Installation Instructions Section 2 2-12 Determine Type Of Solution Needed CAUTION Use only Manitowoc-approved Ice Machine Cleaner (part number 94-0546-3) or Sanitizer (part 94-0565-3) in the AuCS ® A It is a violation of Federal law to use these solutions in a manner inconsistent with their labelin...
Page 21 - Changing Solution Type; Hose Priming
Section 2 Installation Instructions 2-13 Changing Solution Type CAUTION Do not mix Cleaner and Sanitizer solutions together. It is a violation of Federal law to use these products in a manner inconsistent with their labeling. Use the following procedure to flush the system prior to changing from Cle...
Page 22 - Setting Frequency Of Cleanings; Switch; Removal From Service/Winterization
Installation Instructions Section 2 2-14 Setting Frequency Of Cleanings The AuCS ® A is factory-set to clean (or sanitize) the ice machine approximately once every two weeks. For less frequent cleaning, set the selector switch as indicated below. (Refer to “Component Location and Identification” for...
Page 23 - Section 3; Automatic Operation; Manual Start Operation
Section 3 Ice Machine Operation 3-1 Section 3 Ice Machine Operation Automatic Operation The following occurs when the toggle switch is in the ICE position: • The ice machine control board counts the number of ice harvest cycles. • The AuCS ® A accessory interrupts the ice making mode and starts the ...
Page 24 - Changing Switch Position During Automatic Operation
Ice Machine Operation Section 3 3-2 Changing Switch Position During Automatic Operation Q MODELS/IB MODELS/SU1000C If the toggle switch is moved to OFF prior to the pump dispensing (less than 45 seconds into the cycle) then switched to: ICE A normal ice-making mode begins. CLEAN A manual clean cycle...
Page 25 - Changing Switch Position During
Ice Machine Operation Section 3 3-3 QDUAL ONLY Manual Start Operation Step 1 Set the toggle switch to the OFF position after ice falls from the evaporator at the end of a Harvest cycle. Or, set the switch to the OFF position and allow the ice to melt off the evaporator CAUTION Never use anything to ...
