Makita HRH01 - Manual
Makita HRH01 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – ariation list; Note
- Page 3 – epair; Transmission parts
- Page 4 – Cushion ring 13; Lubrication Around; Swash bearing section: 4g
- Page 9 – Viewed from the upper side
- Page 13 – Tool holder guide section for BHR262T, HR262DT
- Page 15 – Tool holder guide complete for BHR262T, HR262TD
- Page 17 – Swash bearing portion; Piston cylinder portion
- Page 19 – Refer to
- Page 20 – ircuit diagram
- Page 21 – iring diagram; gray
Capacity: mm (")
HR262D/ BHR262
(HRH01C/ HRH01)
*1
HR262TD/ BHR262T
(HRH02C/ HRH02)
*1
Yes
Yes
Yes (by trigger)
13 (1/2)
32 (1-1/4)
26 (1)
4.5 (9.9)
Models No.
Description
C
ONCEPT AND MAIN APPLICATIONS
S
pecification
S
tandard equipment
O
ptional accessories
Note:
The standard equipment
for the tool shown above
may vary by country.
HR262D/
BHR262, HR262TD/
BHR262T
(HRH01C/
HRH01, HRH02C/
HRH02)
*1
26mm (1") Cordless Combination Hammers
W
H
Chuck type
Adapted for
SDS-PLUS bits
Adapted for SDS-PLUS bits
and Round shank bits
*
2
Steel
Wood
Concrete
Variable speed control
Reverse switch
Torque limiter
Grip assembly ........................ 1
Depth gauge (Stopper pole) ... 1
Quick change drill chuck
....... 1
(for HR262TD/BHR262T,
HRH02/HRH02C
*
1
)
Bit grease ............................... 1
(for some country)
Waste cloth ............................ 1
(for some country)
SDS-PLUS bits
Taper shank TCT bits
Taper shank adapter
Cotter
Grip drill
Grip drill holder
Drill chuck assembly
Chuck adapter
Drill chuck S13
Chuck key S13
SDS-Plus hammer chuck set
Scraper assembly
Dust cup 5
Dust cup 9
Dust extractor attachment
Grease vessel 30g
Hose
Joint 25
Bit grease
Plastic carrying case
Depth gauge (Stopper pole)
Blow out bulb
Cold chisels
Keyless drill chuck
Safety goggles
Dust cup
Battery
Voltage: V
Capacity: Ah
Charging Time: min.
36
2.2/ 2.6
Cell
Li-ion
60 with DC36WA/ 22 with DC36RA
Energy capacity: Wh
80/ 94
Yes
LED job light
These 36V cordless combination hammers have been developed based on
Models BHR261 and BHR261T, and feature compatibility with both
Makita 36V-2.6Ah Li-ion battery BL3626 and 36V-2.2Ah Li-ion battery
BL3622A.
(
Note
: BHR261 and BHR261T run on only 36V-2.6Ah battery BL3626.)
Other features are exactly the same as BHR261 and BHR261T as follows:
• 3 operation modes (rotation only/ rotation with hammering/ hammering only)
• Vibration absorbing handle and soft grips
• Good tool-balance due to the center of gravity closer to handle
HR262TD/BHR262T (HRH02/HRH02C
*1
) are equipped with
quick change chuck.
These new products are available in the variations listed in the next page.
Max. output (W)
500
0 - 1,200
0 - 4,800
No load speed: min.
ˉ
¹ = rpm
Impacts per minute= min.
ˉ
¹
Dimensions: mm (")
Width (W)
Height (H)
Length (L)
387
(15-1/4)
104 (4-1/8)
235 (9-1/4)
363
(14-1/4)
HR262D/
BHR262
HR262TD/
BHR262T
3 modes
(Rotation only/ Rotation with hammering/ Hammering only)
Operation mode
P 1/2
2
Weight according to
EPTA-Procedure 01/2003
*
3
: kg (lbs)
4.8 (10.6)
PRODUCT
T
ECHNICAL INFORMATION
*2
Round shank bits can also be used by replacing the factory-mounted chuck with Quick change drill chuck (keyless).
*3
with Battery and Side grip
Grooving chisels
Bull points
Scaling chisels
Fast charger DC36RA
Battery BL3626
Charger DC36WA
Battery BL3622A
Battery adapter BAP36N
Battery converter BCV01
Battery converter BCV02
Side grip set
Grip base set
*1
Model numbers for North and Central American countries
L
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
P 2/2 2 V ariation list BHR262Z2CBHR262RD Model No. Type Quantity Battery adapter Battery converter Plastic carrying case Battery cover Yes Battery BHR262DP1 No No BHR262Z No 1 No No No No BAP36N BCV01 No No HR262DZ No No No No HR262DWB Yes 1 No HR262DWBE 2 BL3622A 1 DC36RA Charger No No No No No No...
[2] LUBRICATION [1] NECESSARY REPAIRING TOOLS R epair Description Code No. Use for Retaining ring S pliers ST-2N 1R003 Removing Ring spring 19 from Tool holder complete/ Tool holder guide complete Retaining ring S pliers ST-2 Bearing plate (for arbor press) 1R004 Removing Ring spring 29 1R022 or 1R3...
Gear section: 17g Crank section: 5g boss for fixing Compression spring 14 [Inside view of Inner housing] [2] LUBRICATION (cont.) Apply Makita grease RB No.00 to the following portions indicated by black triangle to protect parts and product from unusual abrasion. Fig. 2 Fig. 3 BHR262 HR262D BHR262T ...
