Makita HR2431 - Manual - manualsarea.com

Page 2 - SPECIFICATIONS; GENERAL SAFETY RULES; Read and understand all instructions.; Failure to follow all; SAVE THESE INSTRUCTIONS

2 SPECIFICATIONS • Manufacturer reserves the right to change specifications without notice. • Specifications may differ from country to country. GENERAL SAFETY RULES USA002-2 (For All Tools) WARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result in...

Page 4 - SPECIFIC SAFETY RULES

4 21. Check for misalignment or binding of moving parts, breakage of parts, and anyother condition that may affect the toolsoperation. If damaged, have the tool ser-viced before using. Many accidents are caused by poorly maintained tools. 22. Use only accessories that are recom- mended by the manufa...

Page 6 - Selecting the action mode

6 FUNCTIONAL DESCRIPTION CAUTION: • Always be sure that the tool is switched off andunplugged before adjusting or checking function on thetool. Switch action CAUTION: • Before plugging in the tool, always check to see that theswitch trigger actuates properly and returns to the “OFF”position when rel...

Page 7 - Torque limiter; ASSEMBLY; Installing or removing the bit

7 Torque limiter The torque limiter will actuate when a certain torque level isreached. The motor will disengage from the output shaft.When this happens, the bit will stop turning. CAUTION: • As soon as the torque limiter actuates, switch off the toolimmediately. This will help prevent premature wea...

Page 8 - Installing dust extractor attachment

8 Insert the bit into the tool. Turn the bit and push it in until itengages. If the bit cannot be pushed in, remove the bit. Pull the chuckcover down a couple of times. Then insert the bit again. Turnthe bit and push it in until it engages. After installing, always make sure that the bit is securely...

Page 9 - Installing dust bag

9 Insert firmly the hose of the dust extractor attachment intothe hose port of the tool until the hose hits against the bottomof the port to be fixed firmly to the tool. Installing dust bag Keeping the angle of the dust bag with the tool at 90 ° , insert the dust bag into the dust exhaust port of th...

Page 10 - Depth adjustment; OPERATION; Drilling with dust extractor attachment

10 Depth adjustment Loosen the screw of the stopper by turning it counterclock-wise so that the stopper could slide on the depth gauge ofthe dust extractor attachment. Slide the stopper to thedesired drilling depth of the gauge, and then tighten thescrew by turning it clockwise. OPERATION Drilling w...

Page 11 - Hammer drilling operation; Drilling in wood or metal

11 Hammer drilling operation Set the action mode changing knob to the symbol. Position the bit at the desired location for the hole, then pullthe switch trigger. Do not force the tool. Light pressure givesbest results. Keep the tool in position and prevent it from slip-ping away from the hole.Do not...

Page 12 - MAINTENANCE

12 CAUTION: • Never use “rotation with hammering” when the drillchuck assembly is installed on the tool. The drill chuckassembly may be damaged. Also, the drill chuck willcome off when reversing the tool. • Pressing excessively on the tool will not speed up thedrilling. In fact, this excessive press...

Page 13 - ACCESSORIES

13 ACCESSORIES CAUTION: • These accessories or attachments are recommended foruse with your Makita tool specified in this manual. Theuse of any other accessories or attachments mightpresent a risk of injury to persons. Only use accessoryor attachment for its stated purpose. If you need any assistanc...

Page 14 - Memo

Page 18 - MAIL THIS PORTION; Your answers to the following questions are appreciated.; Please return this portion by facsimile or mail.

18 1. This product was purchased from: Home Center Hardware/Lumber Store Tool Distributor Industrial Supply Construction Supply Other ( ) 3. How did you learn about this product: Magazine From Dealer Newspaper Store Display Catalog Radio Exhibition From Friend Previous Usage Other ( ) 2. Use of the ...

Page 19 - FACTORY SERVICE CENTERS; RETAIN THIS PORTION FOR YOUR RECORDS

19 FACTORY SERVICE CENTERS 1-800-4-MAKITA RETAIN THIS PORTION FOR YOUR RECORDS ARIZONA 3707 E. Broadway Rd., Ste. 6 Phoenix, AZ 85040 (602) 437-2850 CALIFORNIA 41850 Christy St. Fremont, CA 94538-5107 (510) 657-9881 14930 Northam St. La Mirada, CA 90638-5753 (714) 522-8088 1970 Fulton Avenue Sacrame...

Page 20 - WARNING; MAKITA LIMITED ONE YEAR WARRANTY; Warranty Policy; Makita Corporation

WARNING Some dust created by power sanding, sawing, grinding, drilling, and otherconstruction activities contains chemicals known to the State of Californiato cause cancer, birth defects or other reproductive harm. Some examplesof these chemicals are:• lead from lead-based paints, • crystalline sili...

Makita HR2431 - Manual

Table of Contents:

Summary

Other Makita Models