Makita BTW072 - Manual - manualsarea.com

Page 2 - SPECIFICATIONS; • Specifications may differ from country to country.; GENERAL SAFETY RULES; Read and understand all instructions.; Failure to follow all; SAVE THESE INSTRUCTIONS; Work Area

2 SPECIFICATIONS • Manufacturer reserves the right to change specifications without notice. • Specifications may differ from country to country. GENERAL SAFETY RULES USA003-1 (FOR All BATTERY OPERATED TOOLS) WARNING: Read and understand all instructions. Failure to follow all instructions listed bel...

Page 4 - SERVICE; SPECIFIC SAFETY RULES

4 SERVICE 21. Tool service must be performed only byqualified repair personnel. Service or main- tenance performed by unqualified personnelmay result in a risk of injury. 22. When servicing a tool, use only identicalreplacement parts. Follow instructions inthe Maintenance section of this manual. Use...

Page 5 - SYMBOLS; The followings show the symbols used for tool.

5 SYMBOLS USD302-1 The followings show the symbols used for tool. V ....................... volts ................... direct current ................... no load speed .../min ................ revolutions or reciprocation per minute ................ number of blow IMPORTANT SAFETY INSTRUCTIONS FOR CH...

Page 9 - Conditioning charge

9 NOTE: • The battery charger is for charging Makita batterycartridge. Never use it for other purposes or for othermanufacturer’s batteries. • When you charge a new battery cartridge or a batterycartridge which has not been used for a long period oftime, it may not accept a full charge. This is a no...

Page 11 - Checking the remaining battery capacity; When charging; Switch action; Always check the direction of rotation before operation.

11 Checking the remaining battery capacity When charging When the charging begins, the first (far left) indicating lampbegins to flicker. Then, as charging proceeds, the otherlamps light, one after the other, to indicate the battery capac-ity. When using When the tool is switched on, the lamps will ...

Page 12 - Pulling the trigger, insert the battery cartridge. Keep on

12 • Use the reversing switch only after the tool comes to acomplete stop. Changing the direction of rotation beforethe tool stops may damage the tool. • When not operating the tool, always set the reversingswitch lever to the neutral position. The remaining Battery capacity Auto-stop mechanism The ...

Page 13 - Confirming the presetting; presetting number is 12.

13 3. Release the trigger. (The indicating lamp will keep light- ing up lit for 0.5 seconds, then the lamp will go out.) 4. Hit the tool housing preset number of first digit except 0. (The indicating lamp will light up in green color. Then,the light goes out.) Example: • When the preset number is 12...

Page 14 - ASSEMBLY; Selecting correct socket

14 Relation between presetting number and action Indicating lamp • After impacting preset numbers, the indicating lamplights in green color. • The red color light will light on if the trigger is pulledbefore the presetting number of impacts is achieved. Itindicates that the operation is incomplete. ...

Page 15 - Installing or removing socket; OPERATION

15 Installing or removing socket To install the socket, push it onto the anvil of the tool until itlocks into place.To remove the socket, simply pull it off. OPERATION [*1] Presetting number of impacts is impossible for more than200 impacts (4 seconds). [*2] Fastening time includes when you pull the...

Page 16 - MAINTENANCE; Replacing carbon brushes

16 1. When the battery cartridge is discharged almost com- pletely, voltage will drop and the fastening torque will bereduced. 2. Socket • Failure to use the correct size socket will cause areduction in the fastening torque. • A worn socket (wear on the hex end or square end)will cause a reduction i...

Page 17 - ACCESSORIES; Automatic refreshing adapter

17 Use a screwdriver to remove the brush holder caps. Take outthe worn carbon brushes, insert the new ones and securethe brush holder caps. To maintain product SAFETY and RELIABILITY, repairs, anyother maintenance or adjustment should be performed byMakita Authorized or Factory Service Centers, alwa...

Page 18 - Memo

Page 20 - Warranty Policy; MAKITA LIMITED ONE YEAR WARRANTY; Makita Corporation

Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects fromworkmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop duringthis one year period, return the COMPLE...

Makita BTW072 - Manual

Table of Contents:

Summary

Other Makita Models