Makita BTD061 - Manual - manualsarea.com

Page 2 - SPECIFICATIONS; GENERAL SAFETY RULES; Read and understand all instructions.; Failure to follow all; SAVE THESE INSTRUCTIONS; Work Area

2 SPECIFICATIONS • Manufacturer reserves the right to change specifications without notice. • Specifications may differ from country to country. GENERAL SAFETY RULES USA003-1 (FOR All BATTERY OPERATED TOOLS) WARNING: Read and understand all instructions. Failure to follow all instructions listed bel...

Page 4 - SERVICE; SPECIFIC SAFETY RULES

4 SERVICE 21. Tool service must be performed only byqualified repair personnel. Service or main- tenance performed by unqualified personnelmay result in a risk of injury. 22. When servicing a tool, use only identicalreplacement parts. Follow instructions inthe Maintenance section of this manual. Use...

Page 5 - SYMBOLS

5 SYMBOLS USD302-1 The followings show the symbols used for tool. V ....................... volts ................... direct current ................... no load speed .../min ................ revolutions or reciprocation per minute ................ number of blow IMPORTANT SAFETY INSTRUCTIONS FOR CH...

Page 9 - Conditioning charge

9 NOTE: • The battery charger is for charging Makita batterycar tridge. Never use it for other purposes or for othermanufacturer’s batteries. • When you charge a new battery car tridge or a batterycar tridge which has not been used for a long period oftime, it may not accept a full charge. This is a...

Page 10 - Tips for maintaining maximum battery life; Refresh charging; When charging

10 Tips for maintaining maximum battery life 1. Charge the battery car tridge before completely dis- charged.Always stop tool operation and charge the battery car-tridge when you notice less tool power. 2. Never recharge a fully charged battery cartridge. Overcharging shor tens the battery service l...

Page 12 - ASSEMBLY; Installing or removing driver bit or socket bit; OPERATION

12 ASSEMBLY CAUTION: • Always be sure that the tool is switched off and thebattery cartridge is removed before carrying out anywork on the tool. Installing or removing driver bit or socket bit Use only the driver bit or socket bit shown in the figure. Donot use any other driver bit or socket bit. To...

Page 14 - MAINTENANCE; Replacing carbon brushes; ACCESSORIES

14 MAINTENANCE CAUTION: • Always be sure that the tool is switched off and thebattery car tridge is removed before attempting toperform inspection or maintenance. Replacing carbon brushes Remove and check the carbon brushes regularly. Replacewhen they wear down to the limit mark. Keep the carbonbrus...

Page 15 - Memo

Page 18 - MAIL THIS PORTION; Your answers to the following questions are appreciated.; Please return this portion by facsimile or mail.

18 1. This product was purchased from: Home Center Hardware/Lumber Store Tool Distributor Industrial Supply Construction Supply Other ( ) 3. How did you learn about this product: Magazine From Dealer Newspaper Store Display Catalog Radio Exhibition From Friend Previous Usage Other ( ) 2. Use of the ...

Page 19 - FACTORY SERVICE CENTERS; RETAIN THIS PORTION FOR YOUR RECORDS

19 FACTORY SERVICE CENTERS 1-800-4-MAKITA RETAIN THIS PORTION FOR YOUR RECORDS ALABAMA 2365 Pelham ParkwayPelham, AL 35124 (205) 620-1791 ARIZONA 3707 E. Broadway Rd., Ste. 6 Phoenix, AZ 85040 (602) 437-2850 ARKANSAS Shackleford Shopping Center 240 South Shackleford Rd., Ste. C Little Rock, AR 72211...

Page 20 - WARNING; MAKITA LIMITED ONE YEAR WARRANTY; Warranty Policy; Makita Corporation

WARNING Some dust created by power sanding, sawing, grinding, drilling, and otherconstruction activities contains chemicals known to the State of Californiato cause cancer, birth defects or other reproductive harm. Some examplesof these chemicals are:• lead from lead-based paints, • crystalline sili...

Makita BTD061 - Manual

Table of Contents:

Summary

Other Makita Models