Makita 6918D - Manual - manualsarea.com

Page 2 - SPECIFICATIONS; GENERAL SAFETY RULES; Read and understand all instructions.; Failure to follow all; SAVE THESE INSTRUCTIONS

2 SPECIFICATIONS • Manufacturer reserves the right to change specifications without notice. • Specifications may differ from country to country. GENERAL SAFETY RULES USA003-1 (FOR All BATTERY OPERATED TOOLS) WARNING: Read and understand all instructions. Failure to follow all instructions listed bel...

Page 3 - Work Area; Electrical Safety

3 Work Area 1. Keep your work area clean and well lit. Cluttered benches and dark areas invite acci-dents. 2. Do not operate power tools in explosiveatmospheres, such as in the presence offlammable liquids, gases, or dust. Power tools create sparks which may ignite the dustor fumes. 3. Keep bystande...

Page 4 - SERVICE; SPECIFIC SAFETY RULES

4 19. Check for misalignment or binding ofmoving parts, breakage of parts, and anyother condition that may affect the tool’soperation. If damaged, have the tool ser-viced before using. Many accidents are caused by poorly maintained tools. 20. Use only accessories that are recom-mended by the manufac...

Page 5 - SYMBOLS

5 SYMBOLS USD302-1 The followings show the symbols used for tool. V ....................... volts ................... direct current ................... no load speed .../min ................ revolutions or reciprocation per minute ................ number of blow IMPORTANT SAFETY INSTRUCTIONS FOR CH...

Page 8 - Tips for maintaining maximum battery life

8 NOTE: • The battery charger is for charging Makita batterycartridge. Never use it for other purposes or for othermanufacturer’s batteries. • When you charge a new battery cartridge or a batterycartridge which has not been used for a long period oftime, it may not accept a full charge. This is a no...

Page 9 - ASSEMBLY; Selecting correct socket

9 Switch action CAUTION: • Before inserting the battery cartridge into the tool,always check to see that the switch trigger actuatesproperly and returns to the “OFF” position whenreleased. To start the tool, simply pull the switch trigger. Tool speed isincreased by increasing pressure on the switch ...

Page 10 - Installing or removing socket; OPERATION

10 Installing or removing socket To install the socket, push it onto the anvil of the tool until itlocks into place.To remove the socket, simply pull it off. OPERATION The proper fastening torque may differ depending upon thekind or size of the bolt, the material of the workpiece to befastened, etc....

Page 11 - MAINTENANCE; Replacing carbon brushes

11 2. Socket • Failure to use the correct size socket will cause areduction in the fastening torque. • A worn socket ( wear on the hex end or square end )will cause a reduction in the fastening torque. 3. Bolt • Even though the torque coefficient and the class ofbolt are the same, the proper fasteni...

Page 12 - Recycling the Battery

12 Use a screwdriver to remove the brush holder caps. Take outthe worn carbon brushes, insert the new ones and securethe brush holder caps. After replacing brushes, insert the battery cartridge into thetool and break in brushes by running tool with no load forabout 1 minute. Then check the tool whil...

Page 13 - ACCESSORIES

13 ACCESSORIES CAUTION: • These accessories or attachments are recommended foruse with your Makita tool specified in this manual. Theuse of any other accessories or attachments mightpresent a risk of injury to persons. Only use accessoryor attachment for its stated purpose. If you need any assistanc...

Page 14 - Memo

Page 18 - MAIL THIS PORTION; Your answers to the following questions are appreciated.; Please return this portion by facsimile or mail.

18 1. This product was purchased from: Home Center Hardware/Lumber Store Tool Distributor Industrial Supply Construction Supply Other ( ) 3. How did you learn about this product: Magazine From Dealer Newspaper Store Display Catalog Radio Exhibition From Friend Previous Usage Other ( ) 2. Use of the ...

Page 19 - FACTORY SERVICE CENTERS; RETAIN THIS PORTION FOR YOUR RECORDS

19 FACTORY SERVICE CENTERS 1-800-4-MAKITA RETAIN THIS PORTION FOR YOUR RECORDS ALABAMA 2365 Pelham ParkwayPelham, AL 35124 (205) 620-1791 ARIZONA 3707 E. Broadway Rd., Ste. 6 Phoenix, AZ 85040 (602) 437-2850 ARKANSAS Shackleford Shopping Center 240 South Shackleford Rd., Ste. C Little Rock, AR 72211...

Page 20 - WARNING; MAKITA LIMITED ONE YEAR WARRANTY; Warranty Policy; Makita Corporation

WARNING Some dust created by power sanding, sawing, grinding, drilling, and otherconstruction activities contains chemicals known to the State of Californiato cause cancer, birth defects or other reproductive harm. Some examplesof these chemicals are:• lead from lead-based paints, • crystalline sili...

Makita 6918D - Manual

Table of Contents:

Summary

Other Makita Models