Makita 6916FD - Manual - manualsarea.com

Page 2 - SPECIFICATIONS; GENERAL SAFETY RULES; Read and understand all instructions.; Failure to follow all

2 SPECIFICATIONS • Manufacturer reserves the right to change specifications without notice. • Specifications may differ from country to country. GENERAL SAFETY RULES USA003-2 (FOR ALL BATTERY OPERATED TOOLS) WARNING: Read and understand all instructions. Failure to follow all instructions listed bel...

Page 3 - SAVE THESE INSTRUCTIONS; Work Area; Electrical Safety

3 SAVE THESE INSTRUCTIONS Work Area 1. Keep your work area clean and well lit. Cluttered benches and dark areas invite acci-dents. 2. Do not operate power tools in explosiveatmospheres, such as in the presence offlammable liquids, gases, or dust. Power tools create sparks which may ignite the dustor...

Page 4 - Service; SPECIFIC SAFETY RULES

4 18. Maintain tools with care. Keep cuttingtools sharp and clean. Properly maintained tools with sharp cutting edge are less likely tobind and are easier to control. 19. Check for misalignment or binding ofmoving parts, breakage of parts, and anyother condition that may affect the tool’soperation. ...

Page 5 - SYMBOLS

5 SYMBOLS USD302-1 The followings show the symbols used for tool. V ....................... volts ................... direct current ................... no load speed .../min ................ revolutions or reciprocation per minute ................ number of blow IMPORTANT SAFETY INSTRUCTIONS FOR CH...

Page 8 - Tips for maintaining maximum battery life

8 NOTE: • The battery charger is for charging Makita batterycartridge. Never use it for other purposes or for othermanufacturer’s batteries. • When you charge a new battery cartridge or a batterycartridge which has not been used for a long period oftime, it may not accept a full charge. This is a no...

Page 9 - Reversing switch action

9 Switch action CAUTION: • Before inserting the battery cartridge into the tool,always check to see that the switch trigger actuatesproperly and returns to the “OFF” position whenreleased. To start the tool, simply pull the switch trigger. Tool speed isincreased by increasing pressure on the switch ...

Page 10 - ASSEMBLY; Installing or removing driver bit or socket bit; OPERATION

10 ASSEMBLY CAUTION: • Always be sure that the tool is switched off and thebattery cartridge is removed before carrying out anywork on the tool. Installing or removing driver bit or socket bit Use only the driver bit or socket bit shown in the figure. Donot use any other driver bit or socket bit. To...

Page 12 - MAINTENANCE; Replacing carbon brushes

12 MAINTENANCE CAUTION: • Always be sure that the tool is switched off and thebattery cartridge is removed before attempting toperform inspection or maintenance. Replacing carbon brushes Remove and check the carbon brushes regularly. Replacewhen they wear down to the limit mark. Keep the carbonbrush...

Page 13 - ACCESSORIES

13 ACCESSORIES CAUTION: • These accessories or attachments are recommended foruse with your Makita tool specified in this manual. Theuse of any other accessories or attachments mightpresent a risk of injury to persons. Only use accessoryor attachment for its stated purpose. If you need any assistanc...

Page 14 - Memo

Page 18 - Your answers to the following questions are appreciated.; Certificate of Warranty

18 Your answers to the following questions are appreciated. Date Purchased Model No. Serial No. Initial Last Name Street Address City Province AGE: Male Female Married Single Month Day Year 20 Under 19 20-29 30-39 40-49 Over 50 Paste Paste Paste Paste Paste Paste Paste Paste P aste P aste P aste P a...

Page 19 - Factory Service Centres; CUSTOMER RECORD

19 Factory Service Centres For the authorized service centre nearest you please refer to the local yellow pages directory under “tools” or con-tact our customer service department (Tel) 1-800-263-3734 When you need service... • Explain the problem in a letter • Enclose the letter with the tool • Pac...

Page 20 - Warranty Policy; MAKITA LIMITED ONE YEAR WARRANTY; Makita Corporation

Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects fromworkmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop duringthis one year period, return the COMPLE...

Makita 6916FD - Manual

Table of Contents:

Summary

Other Makita Models