Page 2 - LDVR Series Direct Vent Gas Fireplace; PLEASE READ THE INSTALLATION & OPERATING INSTRUCTIONS; Table of Contents
2 LDVR Series Direct Vent Gas Fireplace 10007317 PLEASE READ THE INSTALLATION & OPERATING INSTRUCTIONS BEFORE USING APPLIANCE. Thank you and congratulations on your purchase of a CFM Specialty Home Products fireplace. IMPORTANT: Read all instructions and warnings carefully before starting install...
Page 3 - CAUTION: Due to high glass surface temperature chil-; PLEASE REVIEW THE FOLLOWING CAREFULLY; Please ensure that your room is well ventilated - open; Locating Your Fireplace; Installation & Operating Instructions; Proposition 65 Warning:
3 LDVR Series Direct Vent Gas Fireplace 10007317 This gas appliance should be installed by a qualified installer in accordance with local building codes and with current CSA-B149.1 Installation codes for Gas Burning Appliances and Equipment. For USA Installations follow local codes and/or the current...
Page 4 - Fireplace Dimensions; Fireplace specifications and framing dimensions.; Framing Dimensions
4 LDVR Series Direct Vent Gas Fireplace 10007317 Fireplace Dimensions F V - Rough Opening Width Rough Opening Height Rough Opening Depth S S U T R E I H J D A Q B K L G M O Gas Line Access Gas Line Access Low Voltage Electrical Access Electrical Access C �� Centerline of 7" Collar M N P Low Volt...
Page 5 - Hearth; Mantel; Combustible mantel leg minimum installation.; Mantel Chart; Combustible mantel minimum installation.
5 LDVR Series Direct Vent Gas Fireplace 10007317 Top of Unit to Ceiling ............................. 36” (914mm) Appliance Top ....................................................... 0” (0 mm) Bottom .................................................. 0” (0 mm) Side ....................................
Page 6 - DO NOT; Final Finishing; Vented Gas Fireplace Heaters; Framing and Finishing; Input ratings are shown in BTU per hour and are; nail flange; Flange; Flange Location for
6 LDVR Series Direct Vent Gas Fireplace 10007317 Max. Min. Input Input Model Fuel Gas Control BTU/h BTU/h 33LDVRRN Nat Millivolt 16,000 11,200 33LDVRRP Prop Millivolt 16,000 12,000 33LDVREN Nat 24V Hi/Lo 16,000 11,200 33LDVREP Prop* 24V Hi/Lo 16,000 12,000 36LDVRRN Nat Millivolt 19,500 13,650 36LDVR...
Page 7 - Alternate Switch Location; INSTA VENT FREE; Typical gas supply installation.; alternate; Alternate switch location.; Remote switch; Gas; Remote switch wiring diagram.
7 LDVR Series Direct Vent Gas Fireplace 10007317 Installation 1. Thread the wiring through the holes on the end panels of the fireplace. Take care not to cut the wire or insulation on metal edges. Route the wire to a conveniently located receptacle box. 2. Attach the wire to the ON/OFF switch and ins...
Page 8 - Electronic Gas Control Valve
8 LDVR Series Direct Vent Gas Fireplace 10007317 The fireplace, when installed, must be electrically connected and grounded in accordance with local codes or, in the ab- sence of local codes, with the current CSA C22.1 Canadian Electrical Code. For USA installations follow local codes and the nationa...
Page 9 - General Venting; There must not be any obstruction; POWER CORD; SIT822 Valve with Synetek electronic control wiring diagram.
9 LDVR Series Direct Vent Gas Fireplace 10007317 Your fireplace is approved to be vented either through the side wall, or vertically through the roof. • Only CFM Corporation venting components specifi- cally approved and labelled for this fireplace may be used. • Vent terminations shall not be recessed...
Page 10 - General Venting Information - Termination Location; Canadian Installations
10 LDVR Series Direct Vent Gas Fireplace 10007317 V V V V V V V X X X D E B B B C B M B A J K F L VENT TERMINATION AIR SUPPLY INLET AREA WHERE TERMINAL IS NOT PERMITTED H I ����� ������ ����� ������ �������� �������� ����� ������ V B CFM145a DV Termin Location 5/01/01 Rev. 12/05/01 sta INSIDE CORNER...
Page 11 - Termination Clearances; Canadian Installations:; Flex Vent Pipes; Termination clearances.; flex vent; Apply high temperature sealant to 4” and 7” pipes.
11 LDVR Series Direct Vent Gas Fireplace 10007317 Outside Corner Inside Corner Termination Clearances Termination clearances for buildings with combustible and noncombustible exteriors. A = Combustible 6"(152mm)Noncombustible 2"(50mm) B = Combustible 6"(152mm)Noncombustible 2"(50mm) ...
Page 12 - How to Use the Vent Graph; Horizontal dimension from the outside face of the; Vertical dimension from the fl; DV Graphic; Twist Lock Pipes
12 LDVR Series Direct Vent Gas Fireplace 10007317 The vent chart should be read in conjunction with the following vent installation instructions to determine the relationship of the vertical and horizontal dimensions of the vent system.1. Determine the height of the center of the horizontal vent pip...
Page 13 - R E A R V E N T- TO P V I E W; Rear Wall Installation; Combustible Walls; Vent Opening; Locate vent opening on wall.; Adjustable zero clearance sleeve.
13 LDVR Series Direct Vent Gas Fireplace 10007317 DVR584-600 Rear vent no elbows 2/99 djt 20" (508mm) Top View Straight Venting FP836 Rear Vent-Top View 11/21/98 2 0 " ( 5 0 8 m m ) M a x . R E A R V E N T- TO P V I E W 2 0 " ( 5 0 8 m m ) M a x . Top View Rear Vent Corner Installation F...
Page 14 - DVR Series Typical corner install; Firestop; Side View Vent Termination; Side view of final unit location.; Vertical Sidewall Applications; Grasp the vent pipe close to the collar and bend to
14 LDVR Series Direct Vent Gas Fireplace 10007317 CFM133 DVR Series Typical corner install 2/26/01 sta Zero Clearance Sleeve Firestop CFM133 Fig. 17 Firestop and zero clearance sleeve in place. FP1005 Side View Vent Termination 1/25/00 djt Finished Wall Vent Termi- nation FP1005 Fig. 18 Side view of...
Page 15 - Maximum horizontal vent run.; Maximum vent run with elbows.; Maximum number of elbows.
15 LDVR Series Direct Vent Gas Fireplace 10007317 •IMPORTANT• Minimum clearance between vent pipes and combustible materials is one (1”) inch (25 mm) on bottom, sides and top. Twist Lock Vent Starter Kit 7TDVSK, plus Transition Elbow 7TDVRT90 must be used in Vertical Sidewall installations. The 4” p...
Page 16 - Vertical Sidewall Installation; Vent Opening for Combustible Wall; Adjustable Zero Clear-
16 LDVR Series Direct Vent Gas Fireplace 10007317 Vertical Sidewall Installation STEP 1 Locate vent opening on the wall. It may be necessary to first position the fireplace and measure to obtain hole location. Depending on whether the wall is combustible or noncombustible, cut opening to size. (Fig. 2...
Page 17 - Apply high temperature sealant.; zontal venting on a; Measure horizontal length including 2” overlap.; Below Grade Installations
17 LDVR Series Direct Vent Gas Fireplace 10007317 STEP 6 Apply high temperature sealant to 4” (102 mm) and 7” (178 mm) collars or the termination one inch away from the end. Guide the vent terminationʼs 4” and 7” collars into their respective vent pipes. Double check that the vent pipes overlap the ...
Page 18 - Do not back fill around snorkel. A; Snorkel; Snorkel installation, recessed foundation.; Below grade installation; Below grade installation.
18 LDVR Series Direct Vent Gas Fireplace 10007317 Do not back fill around snorkel. A clearance of at least 4” (102mm) must be maintained between the snorkel and the soil. BG401 Snorkel 2/10/99 djt Foundation Recess Snorkel Wall Screws Recess Brackets Watertight Seal Around Pipe Sheet Metal Screws BG4...
Page 19 - Typical vertical; Typical vertical roof applications.
19 LDVR Series Direct Vent Gas Fireplace 10007317 Vertical Through-the-Roof Installation CFM100 Firestop-Vertical 09/20/00 11" 11" Joist Joist Firestop Spacer Nails (4) Upper Floor Attic Insulation Shield Ceiling Instal- lation CFM100 Fig. 35 Place firestop spacer(s) and secure. FP1021 Typica...
Page 20 - Minimum termination to roof clearance.
20 LDVR Series Direct Vent Gas Fireplace 10007317 FP1022 Typical Straight Up Installation 1/26/00 djt 40ʼ (12m) Storm Collar Roof Flash- ing Vent Termination Roof 2ʼ Min. Roof Support Attic Insulation Shield Attic Insulation Joists Joists FP1022 Fig. 37 Typical straight-up installation. Min. 2' (610...
Page 21 - Vent Components; Vent components; Venting Components
21 LDVR Series Direct Vent Gas Fireplace 10007317 Venting Components 584G Venting Components Firestop spacer 2/25/99 djt 584H Venting components attic insulation shield 2/25/99 djt 584I vent components offset support 2/25/99 djt 584D Vent Components 90 degree elbow 2/25/99 djt 10/20/99 twist lock 58...
Page 22 - Operating Instructions; Glass Information; Louvre removal; Remove top louvre; remove glass frame; Window frame assembly removal.
22 LDVR Series Direct Vent Gas Fireplace 10007317 Only glass approved by CFM Specialty Home Products should be used on this fireplace. The top louvre panel is removed by lifting the panel vertically and pulling it away from the appliance. (Fig. 39) The lower access door is hinged along the bottom edg...
Page 23 - Installation of Logs, Lava Rock & Ember Material; Log Installation; Log Identification Chart; Location
23 LDVR Series Direct Vent Gas Fireplace 10007317 1. Remove the top louvre assembly.2. Open the bottom louvre. 3. Remove the window frame assembly. 4. Remove log box from inside firebox. 5. Unpack the logs from packaging and remove each log from its wrapping material. Set aside the ember and the lava...
Page 24 - Correct log placement for 36LDVR.; Correct log placement for 39LDVR.; Do not place any of the lava rock material; Correct log placement for 43LDVR.
24 LDVR Series Direct Vent Gas Fireplace 10007317 LG383 36LDVR logs 1/05 Rear (B135) Front Left (B136) Front Center (B138) Front Right (B137) LG383 Fig. 42 Correct log placement for 36LDVR. 39LDVR 1. Place rear lob (BC14) on rear bracket (ensure log is centered and seated properly to the log support...
Page 25 - Flame Characteristics; Honeywell Valve; 3LDV log flames; 6LDV log flames
25 LDVR Series Direct Vent Gas Fireplace 10007317 RN/RP & EN/EP Models For units equipped with “HI/LO” valves the flame adjustment is accomplished by rotating the “HI/LO” adjustment knob located near the center of the gas control valve. (Figs. 45 & 46) It is important to periodically perform ...
Page 26 - FOR YOUR SAFETY READ BEFORE LIGHTING; To Turn Off Gas To Heater; Lighting and Operating Instructions; Lighting Instructions; Euro SIT
26 LDVR Series Direct Vent Gas Fireplace 10007317 3. Open control access panel. 4. Push in gas control knob slightly and turn clock- wise to “OFF”. Do not force. 5. Close control access panel. 1. STOP! Read the safety information above. 2. Turn off all electrical power to the fireplace. 3. For MN/MP/...
Page 27 - For Fireplaces equipped with SIT822 Gas Valve (EN or EP)
27 LDVR Series Direct Vent Gas Fireplace 10007317 Lighting and Operating Instructions For Fireplaces equipped with SIT822 Gas Valve (EN or EP) A. This fireplace is equipped with an ignition device which automatically lights the pilot. DO NOT try to light the pilot by hand. B. BEFORE OPERATING, smell ...
Page 28 - Troubleshooting - Honeywell Millivolt Valve
28 LDVR Series Direct Vent Gas Fireplace 10007317 Troubleshooting - Honeywell Millivolt Valve Remove Window Frame Assembly Before Service Work START CHECK Gas Supply On ▼ ▼ ▼ ▼ ▼ Pilot Lights With Piezo Ignitor • Lockout Has Engaged. Wait 60 Seconds And Try Again. • For Spark At Electrode While Depr...
Page 29 - Troubleshooting the Gas Control System; Normal Operation
29 LDVR Series Direct Vent Gas Fireplace 10007317 Troubleshooting the Gas Control System SIT 822 Valve with Synetek Electronic Control Operating Diagram Normal Operation ON/OFF Switch Closed? Safe Start Check On? 0 Sec Purge Pilot Flame Sense OK? ON/OFF Switch Opened? Pilot and Main Valve OFF? 0 sec...
Page 30 - Fuel Conversion Instructions; Honeywell valve; Honeywell Gas Valve.
30 LDVR Series Direct Vent Gas Fireplace 10007317 The conversion of this appliance from one gas to another must be carried out by an authorized service provider. 1. Disconnect power to the unit and shut off the gas sup- ply. 2. Remove window frame assembly. 3. Carefully remove the logs & lava ro...
Page 31 - Cleaning the Standing; Maintenance
31 LDVR Series Direct Vent Gas Fireplace 10007317 Burner and Burner Compartment It is important to keep the burner and the burner compartment clean. At least once per year the logs and lava rock/ember material should be removed and the burner compartment vacuumed and wiped out. Remove and refit the l...
Page 32 - LDVR parts
32 LDVR Series Direct Vent Gas Fireplace 10007317 CFM Specialty Home Products reserves the right to make changes in design, materials, specifications, prices and discontinue colors and products at any time, without notice. 33/36/39/43LDVR HI LO 22 21 19a,b 18a,b 41 17 30 33LDVR 1 1a 1b 1c 1d 1e 1f 1a...
Page 33 - LDVR
33 LDVR Series Direct Vent Gas Fireplace 10007317 LDVR (continued) Ref. Description 33LDVR 36LDVR 39LDVR 43LDVR 1. Log Set (complete) 10007567 10007318 10008214 10008314 1a. Log Front Left A43 B136 BC15 BD16 1b. Log Front Right -- B137 BC16 BD17 1c. Log Front Center -- B138 B138 B138 1d. Log Rear --...
Page 34 - Clip Pin Hitch; Fuel Conversion Kits
34 LDVR Series Direct Vent Gas Fireplace 10007317 LDVR (continued) Ref. Description 33LDVR 36LDVR 39LDVR 43LDVR 37. Relief Plate Assy (Burner Base) 10004192 10004192 10004192 10004192 38. Remote Switch Kit (Not shown) 53875 53875 53875 53875 39. Ignition Control from Synetek (EN) 10007939 10007939 1...
Page 35 - FK24 Fan Assembly; Optional Accessories Available; Fan Kits; fan install; FK24 fan placement.
35 LDVR Series Direct Vent Gas Fireplace 10007317 FK24 Fan Assembly This auxiliary fan system increases the efficiency of the circulation of the heated air.The FK24 fan kit allows variable speed control of the circulation fan and also incorporates a heat sensor in the circuit. Specifications 115 Volt ...
Page 36 - Ceramic Refractory Kits; WIRING DIAGRAM; Ceramic panels; Ceramic panel installation.; rear ceramic panel; Rear refractory panel installation.; Remote Controls
36 LDVR Series Direct Vent Gas Fireplace 10007317 Ceramic refractory panels are available in kit form for the LDV series appliances Appliance Model Kit Name 33LDVR 33LDVRCR 36LDVR 36LDVCR 39LDVR 39LDVCR 43LDVR 43LDVCR Ceramic Refractory Kits The fireplace, when installed, must be electrically connect...
Page 37 - Optional Trim Kits; Appliance Model Main Louvre Kit Additional Louvre; Polished Brass; Regular Trim Kit; Screen Door Kit; Filigree Louvre Kit; Appliance Model
37 LDVR Series Direct Vent Gas Fireplace 10007317 Optional Trim Kits Louvre Accent Trim Appliance Model Main Louvre Kit Additional Louvre Polished Brass 33LDVR 33DVLMP 33DVLAP 36LDVR 36DVLMP 36DVLAP 39LDVR 39DVLMP 39DVLAP 43LDVR 43DVLMP 43DVLAP Antique Brass 33LDVR 33DVLMA 33DVLAA 36LDVR 36DVLMA 36D...
Page 39 - IF WARRANTY SERVICE IS NEEDED...; ) Contact your supplier. Make sure you have your warranty,; LIMITED LIFETIME WARRANTY; PRODUCT COVERED BY THIS WARRANTY
39 LDVR Series Direct Vent Gas Fireplace 10007317 BASIC WARRANTY CFM Specialty Home Products (hereinafter referred to collectively as the Company) warrants that your new Vermont Castings or Majestic Gas Fireplace/Stove is free from manufacturing and material defects for a period of one year from the...
Page 40 - Efficiency Ratings; Model; CFM Specialty Home Products
Efficiency Ratings Model EnerGuide Ratings Steady State (%) D.O.E. Fireplace Efficiency (%) Fan-OFF Fan-ON (AFUE%) 33LDVRRN 62.6 81 82 59 33LDVRRP 62.6 82 83 59 33LDVREN 72.7 81 82 59 33LDVREP 72.7 82 83 59 36LDVRRN 57.5 81 82 58 36LDVRRP 57.5 82 83 58 36LDVREN 63.6 81 82 58 36LDVREP 63.6 82 83 58 39L...
