Magnadyne X9 - Manual

5 Harness Quick Reference (continued) HC6 6-Pin Accessory Harness Pink (-) Ignition #3 Output Orange (-) Ground When Armed Output Violet/Black (-) Programmable Channel #4 Output Red / White (-) Channel #3 Output (Trunk Release) White (-) Programmable Output (Dome Lt - Default) Light Brown (-) Progra...

HC1: White 6-Pin High Current Remote Starter Harness (continued) Remove the two 20A fuses prior to connecting these wires and do not replace them until the harness has been plugged into the control module. These wires are the source of current for all the circuits the relay harness willenergize. The...

7 Wiring (continued) By default, the Brown wire is the positive (+) outputconnection for the siren. Current capacity is 2 amps.Make connection to the (+) red wire from the siren.Connect the (-) black wire coming from the siren to agood chassis ground. O p t i o n : ( + ) H o r n O u t p u t ( S e e ...

Wiring (continued) 8 HC3: Black 3-Pin Door Lock Harness (continued) 5 Wire Ground at Rest Door Locking Systems 87 87A 85 86 30 87 87A 85 86 30 To +12 Volts(Battery +) To PowerLock Switch To PowerLock Motors White Wire: Lock Brown Wire: Unlock Green Wire: Lock Blue Wire: Unlock Violet Wire ALA-DL1 Re...

The Black/White wire is a safety input wire. The remote start unit will not activate unless this wire is grounded.When this wire is disconnected from ground, the remote start system is disabled. 1. The primary connection point for the Black/White wire is at the Neutral Safety Switch located on/at th...

12 Brown Wire: Positive Safety Shut Down Input This wire provides instant shutdown for the remote start, when it receives +12 volts. If the brake lights switch inthe vehicle switches +12 volts to the brake light circuit, connect this wire to the output side of the brake switch.This will allow the re...

13 Wiring (continued) HC6 White 6-Pin Connector S o m e v e h i c l e s m a y r e q u i r e a 3 r d i g n i t i o nconnection in order to start the vehicle engine.The Pink wire provides a 200mA (-) groundo u t p u t t h a t b e c o m e s a c t i v e d u r i n g e n g i n ecranking (default Setting)....

This wire will provide a 1 second pulseground when Channel 3 is activated. Thecurrent capacity of this wire is 200mA.This feature allows you to remote controltrunk release or other electric device. Anadditional relay may be required. GM VATS Key Override Using ALA985H Relay: The Violet/Black wire is...

This wire will become grounded when the alarm is in a armed state. This wire can be connected to an optional starter /ignition disable relay - ECU disable relay, fuel pump disable relay or it can be used to activate other functions of thevehicle such as window roll-up. The connection of an additiona...

16 P4 Sensor 2-Stage Sensor: Allows easy connection with quick disconnect ability forother optional devices. 1. Red: +12 Volt Constant Input2. Black: Main Sensor Ground3. Blue: Instant Trigger (-) Input 4. Green: Warn Away (-) Input P6 Antenna / Receiver Plug-In Harnesses (Continued) Black Wire No C...

17 SAVE 4 4 SAVE 4 4 Examine the 3 different feature charts enclosed and decide which feature will get changed. Circling the feature tobe changed will make the programming process much easier to perform. Before 15 seconds has passed, push and release thevalet switch 2 times holding the button down o...

21 Alarm Feature Programming (Group 3) (continued) Before 15 seconds has passed, push and release thevalet switch 8 times holding the button down on the8th press. Wait until four (4) short chirps/beeps + one(1) long chirp/beep is heard. Release the button. Youare now in “Remote Start Feature Program...

22 10 Minute Run Time 20 Minute Run Time 30 Minute Run Time 5 Minute Run Time Factory Alarm Disarm when trunk release(CH#3) is activated Without this Feature Step 3 (continued) One Chirp Two Chirps Three Chirps Four Chirps Button One LED Pulse Two LED Pulses Three LED Pulses Four LED Pulses (Default...

24 Press Buttons Chirp/ LED Flash Checking Type Follow Programming and Test Procedure 1 Voltage Type A. Press two times to start the engine. Allow engine to run for more than 10 seconds. B. If engine starts without cranking too long or too short and runs for more than 10 seconds, press to exit progr...

25 The unit has the ability to report the cause of the last shutdown of the remote start system. 1. Turn the ignition switch to “On” position.2. Press the ( ) button on the transmitter3. The LED will now report the last system shutdown by flashing for 3 cycles in the following grouped patterns: Shut...

26 In this test mode, the installer can save time adjusting the optional sensor sensitivity without using the traditionalarming/disarming procedures to adjust the sensor. With the ignition switch in the OFF position, turn theignition switch On - Off - On - Off - On - Off. ON O F F 3X Before 15 secon...

27 Turn the ignition switch from theOFF position to the ON position 3times leaving it in the Off positionthe third time. ON ON 3X Step 1 Before 15 seconds has passed, pushand release the valet switch 12 times.Holding on the 12th press. You willhear 6 short beeps. Release thebutton. 11X + 1X (Hold) S...

HC1 White 6-Pin P2 Blue 2-Pin P6 Blue 4-Pin HC2 White 5-Pin HC3 Black 2-Pin HC8 Black 8-Pin HC6 White 6-Pin P4 White 4-Pin P1 White 2-Pin P7 Brown 4-Pin Data Port Wiring Diagram X9-IM 7-24-08 Rev. A © Copyright 2008/2009 Magnadyne Corporation