Lowrance GlobalMap 5000C - Manual

iv Delete Trail ............................................................................. 91New Trail................................................................................. 92Trail Visible/Invisible and Other Trail Options .................... 92 Units of Measure..........................

1 Section 1: Read Me First! How this manual can get you out on the road, fast! Welcome to the exciting world of GPS satellite navigation! We knowyou're anxious to begin finding your way with this space-age technol-ogy, but we have a favor to ask. Before you grab the GlobalMap  and begin installing ...

2 Section 3 contains short, easy-to-scan GPS lessons that follow one an-other in chronological order. They're all you'll need to know to find yourway on the water or in the wilderness quickly. After you've learned the basics (or if you already have some GPS expe-rience), you may want to try out some...

4 NOTE: The above memory capacities refer only to the GlobalMap's on-boardmemory. The amount of GPS data you can record and save for recalllater is only limited by the number of MMC cards you have. NOTICE! The storage and operation temperature range for your GlobalMap isfrom -4 degrees to +167 degre...

6 Introduction to GPS and WAAS Well, now you know the basics of how the unit does its work. You mightbe ready to jump ahead to Section 2, Installation & Accessories, on page 11, so you can mount your GlobalMap and plug in the power. Or youmight want to see how our text formatting makes the manua...

8 You'll find that using your GPS receiver is both easy and amazinglyaccurate. It’s easily the most accurate method of electronic navigationavailable to the general public today. Remember, however, that thisreceiver is only a tool. Always have another method of navigation avail-able, such as a map o...

9 For example, instructions for navigating a trail would look like this: 1. From the Map Page, press MENU | MENU | ↓ to M Y T RAILS | ENT . 2. Press ↓ to Trail 1 | ENT | → | ↓ to N AVIGATE | ENT . 3. You are asked to wait while it converts the trail into a route. 4. The wait message disappears and t...

11 Section 2: Installation & Accessories Preparations You can install the GPS system in some other order if you prefer, butwe recommend this installation sequence: Caution: You should read over this entire installation section before drill-ing any holes in your vehicle or vessel! 1. Determine th...

12 You need to select an antenna installation location that has a clear, un-obstructed view of the sky. After the module is installed, route the cableto the unit, plug it in the center socket on the back and your system isready to use. See the module's instruction sheet, publication part num-ber 988...

13 CAUTION: Do not use this product without a 3-amp fuse wired into the powercable! Failure to use a 3-amp fuse will void your warranty. This unit has reverse polarity protection. No damage will occur if thepower wires are reversed. However, the unit will not work until thewires are attached correct...

14 Com-1 wiring to receive DGPS position information from a DGPS receiver. Com-1 wiring to receive NMEA position information from some other GPS receiver. Com-1 wiring to transmit NMEA position information to another NMEA-compatible device. Com-2 wiring to transmit NMEA position information to anoth...

15 Optional R-A-M mounting system. Bracket Installation Mount the GlobalMap in any convenient location, provided there isclearance behind the unit when it's tilted for the best viewing angle. Youshould also make sure there is enough room behind the GlobalMap toattach the power and GPS antenna/receiv...

16 Front view (left) and side view (right) showing dimensions of the GlobalMap GPS unit when mounted on a gimbal bracket. After drilling the hole, pass the antenna connector up through the hole from under the dash. Pass the power cable's bare-wire end down though the hole from the top. If you wish, ...

17 In-dash mounting template for the GlobalMap 5000C or 6000C, showing dimensions. NOTE: The figure above is not printed to scale. A scaled template (FM-3 In-Dash Adapter Kit instructions) is available for free download from our web site, www.lowrance.com. MMC or SDC Memory Card Installation Your Gl...

18 The MMC drawer is located on the front of the case. To install anMMC, twist the drawer retainer counter-clockwise and pull. Thedrawer will come out of the unit. Place the MMC in the drawer face down (see following figures.) Memory card drawer on the GlobalMap 6000C and GlobalMap 5000C. Slide the ...

21 Section 3: Basic GPS Operations This section addresses the unit's most basic GPS operations. The tuto- rials presented in Sec. 3 follow a chronological order. Sec. 4, Advanced GPS Operations , will discuss other more advanced functions and utili- ties. Material in Sec. 4 is arranged in alphabetic...

22 Navigation Page and Map Page.) Each page represents one of the unit'smajor operation modes. 3. MENU – Press this key to show the menus and submenus, which allow you to select a command or adjust a feature. This also accessessearch functions for streets, intersections, addresses and highway exits....

24 Timers command: controls the up timer, down timer and alarm clock settings. Browse MMC Files command: this allows you to view the installed MMC card and the files it contains. Pages The unit has three Page displays that represent the three major operat-ing modes. They are the Satellite Status Pag...

25 Satellite Status Page. Left view indicates unit has not locked on to any satellites and does not have a fix on its position. Right view shows satellite lock-on with a 3D position acquired (latitude, longitude and altitude), and WAAS reception. This screen shows a graphical view of the satellites ...

26 Navigation Page This screen has a compass rose that not only shows your direction oftravel, but also the direction to a recalled waypoint. To get to the Navi-gation Page: Press PAGES | → or ← to N AVIGATION | EXIT . The navigation screen looks like the one below when you're not navi- gating to a ...

28 Navigation Page, backtracking a trail while creating a new trail. In the example figure above, the driver is headed north (a 355º track)toward a waypoint 355º (bearing) away. The cross track error range(white corridor) is 0.20 miles either side of the course. The driver isheaded toward trail wayp...

29 The map zoom range is the distance across the screen. This numbershows in the lower right corner of the screen. In the first example fig-ure below, the range is 4,000 miles from the left edge of the map to theright edge of the map. The Zoom In and Zoom Out keys zoom the map to enlarge or reduce i...

30 The medium-detail U.S. maps contain: all incorporated cities; shadedmetropolitan areas; county boundaries; shaded public lands (such asnational forests and parks); some major city streets; Interstate, U.S.and state highways; Interstate highway exits and exit services informa-tion; large- and medi...

31 can reduce screen clutter and make streets and other map featureseasier to see by simply turning off the display of POIs you're not watching for. (To see how, check the text on Map Detail CategorySelection, page 77. It shows how to use the Map Categories Drawnmenu to turn individual POI displays ...

32 Resize Window is another extremely handy feature for pages that havetwo major windows. You can change the horizontal size of the windowsto suit your viewing preference. Here's how: 1. From any two-window display, press MENU | ↓ to R ESIZE W INDOW | ENT . 2. Two flashing arrows appear along the ce...

33 GPS Quick Reference Start outdoors, with a clear view of the open sky. As you practice, trynavigating to a location at least a few blocks away. While you're learning,navigation in too small an area will constantly trigger arrival alarms. 1. Connect the unit to electric power and the antenna modul...

34 Find Your Current Position Finding your current position is as simple as turning the GlobalMap on.Under clear sky conditions, the unit automatically searches for satel-lites and calculates its position in approximately one minute or less. NOTE: "Clear sky" means open sky, unobstructed by ...

35 The selected airport to the northwest is 4.25 miles away. Selecting Any Map Item With the Cursor 1. Use the zoom keys and the arrow keys to move around the map andfind the item you wish to select. 2. Use the arrow keys and center the cursor cross-hair on the desiredobject. On most items, a pop-up...

36 Category Selection menu, left, and list of the nearest restaurants, right. 4. If you wish, you could scroll ↑ or ↓ here to select another restaurant, but for now we will just accept the nearest one. Press ENT . 5. The POI information screen appears. (This is how you can use theGlobalMap as a busi...

37 Map screen showing Find Waypoint, the result of a restaurant search. 7. To clear the search and return to the last page displayed, press EXIT | EXIT | EXIT | EXIT . (Before you completely exited out of the Search menus, you could have gone looking for another place.) NOTE: Search works from mappi...

38 Sequence for setting a waypoint. Step 1: while traveling, quickly press WPT twice to call up Find Waypoint screen (seen in Step 2) and set a point. Step 3: a message says the waypoint has been saved. Step 4: ve- hicle continues on its way; number waypoint symbol is visible on map. NOTE: The Quick...

39 Create Waypoint by Entering a Position 1. Press WPT | → to S UBCATEGORY column| ↓ to N EW | ENT . 2. Press ↓ to E NTERED P OSITION | ENT | → to C REATE | ENT . 3. Press → to L ATITUDE | ENT . Enter the latitude by pressing ↑ or ↓ to change the first character, then press → to the next character a...

40 Navigation Page, navigating toward waypoint 004 and leaving a trail. Set Man Overboard (MOB) Waypoint One of boating's most terrifying events is having a friend or familymember fall overboard. This situation can be deadly on any body of wa-ter — fresh or salt. It's particularly dangerous at night...

41 Navigating to Man Overboard: Navigation Page, left, and Map Page, right. The victim is astern of the vessel; the GPS shows which direc- tion to steer to for the rescue. The man overboard position is also stored in the waypoint list for futurereference. It can be edited the same as any other waypo...

42 Navigate to cursor. In this example, the cursor has selected the town of Oologah, Oklahoma. 3. Press MENU | ENT and the GlobalMap will begin navigating to the cursor location. The Map Page will display a red line from your current position to the cur-sor position. The Navigation Page displays a c...

43 lier in this section, or turn to Sec. 6, Searching , for detailed instructions on POI searches.) After you have looked up an item with the Find Waypoint command,use the → to make sure the G O T O command is highlighted at the top of the screen, then press ENT . The GlobalMap begins showing naviga...

44 Sequence for saving a trail and beginning a new one. At left, My Trails command. Center, the Trails Menu. The arrow to the right of Trail 17 indicates the trail is "active," and the check to the left indicates the trail is visible on the map display. The right figure shows the Edit Trail ...

45 Tip: Another quick way to stop recording one trail and begin a new oneis to use the New Trail command: Press MENU | MENU | ↓ to M Y T RAILS | ENT | ENT . Caution: You also have the option of completely turning off trail record-ing, under the trail Options command. However, if the UpdateActive Tra...

48 Navigate trail, map views: at left driver is northbound heading straight toward trail point 6. At right, northbound driver has reached point 6 and has turned west to follow trail. Navigate trail, navigation page (compass rose) views: at left, driver isnorthbound heading straight toward trail poin...

49 NOTE: If you are already located at or near the end of your trail, the arri-val alarm will go off as soon as you hit Enter. Just press EXIT to clear the alarm and proceed. 5. Now, begin moving and follow your GlobalMap. 6. When you reach your destination, be sure to cancel your navigation:press M...

50 The Transfer My Data submenu asks if you want to save data to the MMC or load data from the MMC into the GlobalMap's memory. 2. The Transfer My Data menu includes a message which tells you if anMMC is present or not. If no MMC is present, you must first insert acard into the GlobalMap in order to...

51 From left to right, these figures show the menu sequence for naming and saving a GPS Data File from the GlobalMap's memory to an MMC. 4. Loading to unit memory : There may be more than one GPS Data File (*.USR) on the card. To select a file, press ENT to activate the selec- tion box, use ↓ or ↑ t...

52 Cancel Navigation You can turn off any of the navigation commands after you reach yourdestination or at any other time by using the Cancel Navigation com-mand. Press MENU | MENU | ↓ to C ANCEL N AVIGATION | ENT | ← to Y ES | ENT .

53 Section 4: Advanced GPS Operations Find Distance From CurrentPosition To Another Location 1. While on the Map Page press: MENU | ↓ to F IND D ISTANCE | ENT . 2. Center your cursor over the position you want to find the distance to.A rubber band line appears, connecting your current position to th...

54 called later for navigation purposes. These are sometimes referred to asevent marker icons. The GlobalMap has 42 different symbols you canpick from when creating an icon. Icons are similar to waypoints, but they do not store as much informa-tion (like names) as waypoints do. You can't use a menu ...

55 Delete icons menu. The Delete All Icons command will ask if you are sure. Press ← to Y ES | ENT . All icons will be deleted from the map. The Delete by Symbol command will launch the Select Symbol menu.Press ← or ↑ or → or ↓ to select the icon symbol to delete, then press ENT . A message appears ...

56 waypoint. Once programmed into the GPS unit, a route provides theoption of navigating forward through the route waypoints or in reverseorder (you can even begin navigating in the middle of a route!) Create and Save a Route You have the option of creating and editing a route in the unit, or youcan...

57 Edit Route menu, left. Edit Route Waypoints menu, right, with Add From Map command selected. 3. Use the Zoom keys and arrow keys to move the map and cursor untilthe cursor is centered on the spot where you want your route to begin.(If you are starting at your current position or the current curso...

59 Edit Route Waypoints menu. 3. Use ↓ and ↑ to select a command from the Edit Route Waypoints menu and press ENT . Add From Map lets you insert a waypoint in the route by clicking on a map location with the cursor. Add Waypoint callsup the Waypoint List so you can insert a waypoint from the list. R...

61 Trails Delete a Trail This is the command used to erase or delete a trail:Press MENU | MENU | ↓ to M Y T RAILS | ENT | ↓ to trail name | ENT | → to D ELETE T RAIL | ENT | ← to Y ES | ENT . Tip: You can also delete all trails at once:1. Press MENU | MENU | ↓ to M Y T RAILS | ENT . 2. Press → to D ...

62 then press → to the next character and repeat until the pattern is cor- rect. Press ENT , then EXIT | EXIT | EXIT | EXIT to return to the previous page display. At left, Edit Trail Menu with Pattern option selected. At right, edited trail with dotted line pattern. Utilities Utilities are useful t...

64 accuracy by helping to eliminate errors caused by atmospheric condi-tions and other factors. 1. Press WPT | → to S UBCATEGORY column| ↓ to N EW | ENT . 2. Press ↓ or ↑ to A VERAGE P OSITION | ENT |press → to C REATE | ENT . 3. Wait while the unit takes points to average for the position. (The gre...

65 Section 5: System & GPS Setup Options Alarms This unit has several GPS alarms. The factory default setting has allthe alarms turned on. You can turn the alarms off and on and changetheir distance settings. You can set an arrival alarm to flash a warning message and sound atone when you cross ...

66 4. When your adjustments are finished, return to the last page dis-played by repeatedly pressing EXIT . IMPORTANT ALARM NOTES: Anchor Alarm - The anchor alarm may be triggered even whenyou're sitting still. This typically happens when using small (lessthan 0.05 mile) anchor alarm ranges. Arrival ...

67 GPS Auto Search on the Satellite Status Menu. You can force the unit to immediately kick into auto search mode.Here's how: 1. Press PAGES until you are on the Satellite Status screen. 2. Press MENU | ↓ to GPS A UTO S EARCH | ENT | ← to Y ES | ENT . Check MMC Files and Storage Space To check MMC F...

68 Menus for changing Com Port settings. For assistance in configuring the unit to communicate with anotherdevice, consult the factory; customer service phone numbers are in theback of this manual. Also see the entries below for Configure DGPS and Configure NMEA . To set Com Port Configuration: 1. P...

69 1. Press MENU | MENU | ↓ to S YSTEM S ETUP | ENT . 2. Press ↓ to C OMMUNICATIONS P ORT | ENT | ↓ to C ONFIGURE NMEA | ENT . 3. A menu appears showing the prefixes of the available NMEA sen-tences. A check mark next to a prefix means the prefix is in use. Use ↑ ↓ → ← to select a prefix, then press...

70 datum for you when you select the grid. See the entry on Map DatumSelection for more information. The military grid reference system (MGRS) uses two grid letteringschemes, which are referred to as standard and standard + 10 MGRSon this unit. Your position and datum in use determines which one tou...

71 For example, if it shows a distance of UP 4.00" and LEFT 0.50", youthen measure up four inches and to the left a half-inch from the refer-ence point on the map to find your location. To configure a map fix: To use this format, you need to follow these steps in order. First, takeyour map o...

72 Press ↓ to S ELECT O RIGIN W AYPOINT | ENT | ENT | ENT to bring up the waypoint list. Select the waypoint that you saved the reference point under and press ENT . The unit displays a waypoint information screen with the command S ET A S O RIGIN selected; press ENT and the unit returns to the Conf...

74 3. Begin navigating along the trail/route. (If you are close enough to thefirst waypoint, the arrival alarm will usually go off as soon as naviga-tion begins. Press EXIT to clear the alarm.) When navigation starts, press ↑ to increase speed to the desired setting. 4. Press EXIT to turn off the st...

75 Map Data This menu lets you turn the map off, if desired (which turns the mapscreen into a GPS plotter); turn off or on the pop-up map info boxes;draw the map boundaries or boxes around the areas of high detail; orfill land areas with gray. You can also turn on or off Map Overlays,which display l...

76 Map Overlays (Range Rings; Lat/Long Grid) The map screen can be customized with four range rings and/or gridsthat divide the plotter into equal segments of latitude and longitude. Range rings are handy for visually estimating distances on the map.The ring diameters are based on the current zoom r...

77 GPS Setup Menu, left, Map Datum Menu, right. Map Detail Category Selection This menu determines which of the mapping features are shown on thescreen. This includes, waypoints, trails, icons, cities, highways, etc. Youcan selectively turn on or off any of these items, customizing the map toyour ne...

78 Map orientation at left is shown in north up and at right, track up. This is fine if you're always traveling due north. What you see to yourleft corresponds to the left side of the map, to your right is shown onthe right side of the map, and so on. However, if you travel any otherdirection, the m...

79 Navionics  Charts Your GlobalMap can display Navionics  electronic charts on MMCs. They work just like a MapCreate custom map on an MMC. Left, entrance to Chesapeake Bay in a MapCreate 6 custom map, 10 mile zoom. Center, same position on Navionics chart at 11.15 mile zoom and right, 5.56 mile z...

80 To view Port Services information: 1. Use the arrow keys to move the cursor over a Port Services icon.When selected, a pop-up name box appears. 2. Press WPT to display the Port Services Information screen. The Port Services information screen has two windows. The top windowlists the various servi...

81 Tidal Current Information Navionics charts contain Tidal Current information,represented at large zoom ranges by a box icon withthe letter " C ." The icon stands for a Tidal Current Station location. An example is displayed at right. When you zoom in to a sufficiently small zoom range, th...

82 Current Information screen. The Tidal Current Information screen displays daily tidal current datafor this station on this date at the present time. The graph at the top ofthe screen is an approximate view of the flood and ebb pattern for theday, from midnight (MN), to noon (NN) to midnight (MN)....

83 2. After selecting the Tide Station icon, press WPT to display the Tide Information screen. Navionics chart showing Tide Station icon selected by cursor. In the example above, the tide is at 2.8 feet and falling, as shown by the down arrow at the top of the icon. Tide Information screen. The Tide...

84 1. Use → and ← to highlight month, day or year, then press ENT . 2. Use ↑ and ↓ to select the desired month, day or year, then press ENT . To clear the information screen, press EXIT . Pop-up Help Help is available for virtually all of the menu labels on this unit. Byhighlighting a menu item and ...

85 want to experiment with Position Pinning, the same instructions areused to turn the feature on (checked) and off (unchecked.) 1. Press MENU | MENU | ↓ to GPS S ETUP | ENT | ↓ to P OSITION P INNING | ENT . 2. Press EXIT | EXIT to return to the previous page. Reset Options To reset all features to ...

86 Require DGPS command on the GPS Setup Menu. Screen Contrast and Brightness To access the Screen menu, press MENU | MENU | ENT . Once in the Screen menu: To adjust the display's contrast: The C ONTRAST slider bar is already selected. Press → or ← to move the bar. The left end of the scale is minim...

88 To set the Year: Press → to Y EAR | ENT . Press ↑ or ↓ to select the year, then press ENT . The last field in this menu is C ONFIG DST . This feature allows your unit to automatically adjust with the time change caused by Daylight Sav-ing Time (you should only have to set it once). You may select...

89 1. Press MENU | MENU | ↓ to S YSTEM S ETUP | ENT | ↓ to S OFTWARE I NFO | ENT . 2. Read the information displayed on the screen.3. To return to the last page displayed, press EXIT | EXIT | EXIT . Sounds and Alarm Sound Styles Sounds triggered by key strokes and alarms can be adjusted: You first p...

90 Track Smoothing option, turned on. Trail Options There are several options you can use with trails. Some affect all trails,other options can be applied to a particular trail. You can change theway trails are updated, you can display or hide trails, create a newtrail, delete a trail, etc. General ...

91 From the Trails Menu, press → to T RAIL O PTIONS | ENT . With U PDATE A CTIVE T RAIL highlighted, press ENT to check it (turn on) and uncheck it (turn off). Update Trail Criteria (Auto, Time, Distance) The options are automatic, time, or distance. When it's in the defaultautomatic mode, the unit ...

92 Edit Trail menu. New Trail To manually start a new trail, in the Trails Menu, make sure N EW T RAIL is highlighted and press ENT | EXIT . Trail Visible/Invisible and Other Trail Options The name, maximum number of points in the trail, activity, and visi-bility are all changed on the Edit Trail me...

95 Section 6: Searching NOTE: The background map loaded in your unit lets you search for U.S.Interstate Highway exits and exit services, as well as some landfeatures, including cities and lakes. For a full set of searchable landfeatures, including landmarks, streets, addresses and Points of In-teres...

96 Find Address Menu. 3. To enter an address number , press ↑ or ↓ to change the first number, then press → to move the cursor to the next number and re- peat until the number is correct, then press ENT . 4. To enter a street name , press ↓ to S TREET | ENT . There are two op- tions: A. You can spel...

97 NOTE: We recommend that you do not enter a city name unless the list you are given is too large when searching without it. The GlobalMapcan actually search quicker without a city and you save time by notentering a city name. Find city field, left, Search in particular city only option, center; Fi...

98 Tip: If the address also happens to be an item in the Point of Interestdatabase, you can look up the item's phone number in the WaypointInformation list. With the address location selected by the cursor onthe map, press WPT . The POI's Waypoint Information window ap- pears, with the Go To Waypoin...

99 Find Interstate Highway Exits 1. From the Map Page, press MENU | ↓ to H IGHWAY E XITS | ENT , which calls up the Find Exit menu. Find Highway Exits command, left, and Find Exit menu, right. 2. First, select a highway name by pressing ENT , which calls up the Find By Name menu. There are two highw...

100 Find Exit menu, with an exit selected in the Exit List. 4. In the Exit Information screen you have two choices. A. Press ENT to navigate or "go to" the exit. B. Press → | ENT to find the exit on the map. "Go To Exit" option, left, "Find On Map" option, right. Tip: You can...

101 Find Map Places or Points of Interest (POI) 1. Press WPT , press ↓ or ↑ to select a map place or POI category, then press ENT . (To narrow your search, press → then press ↓ or ↑ to select a subcategory before pressing ENT .) You will be given two options; Search By Name or By Nearest. Find Waypo...

102 Find by Name option, left, Find by Name menu, right. 4. When the POI's Waypoint Information screen is displayed, you canchoose to "Go To" the POI waypoint by pressing ENT or find it on the map by pressing → | ENT . Go To Waypoint POI option, left; Find on Map POI option, right. Find Stre...

103 2. You must first fill in a street name in the First Street dialog box.Press ENT to display the Find By Name menu. There are two options: A. You can spell out the street in the top selection box. Press ↑ or ↓ to change the first letter, then press → to move the cursor to the next let- ter and re...

104 4. The Map Page appears, with the cursor pointing to the found street. Map Page showing results of a street search. The cursor points to the located street. If you want to navigate to the found street at the cursor location, justpress MENU | ENT | EXIT . Find an Intersection You must enter one s...

105 5. The Find Streets menu reappears with the first and second streetdialog boxes filled in. In this example, we selected 71st Street as oursecond street. You could now use similar techniques to select a city orZip code, but your search will probably be faster if you leave thoseboxes blank. (You c...

106 Find Waypoints 1. Press WPT | ENT . 2. If searching for the waypoint By Name , press ENT . If searching for the Nearest waypoint, press ↓ to N EAREST | ENT . (To search by name, jump to step 5 below.) Find Waypoint menu, left; Find By Nearest command, center, Find by Name command, right. 3. If y...

107 Waypoint Information screens with the Go To Waypoint command se- lected, left, and the Find on Map command selected, right. To clear these menus and return to the previous page, press EXIT re- peatedly. 5. If you're looking by name , there are two options: A. You can spell out the name in the to...

109 Section 7: Supplemental Material Datums Used by This Unit WGS 1984Default AdindanMean for Ethiopia, Sudan AdindanBurkina Faso AdindanCameroon AdindanEthiopia AdindanMali AdindanSenegal AdindanSudan AfgooyeSomalia Ain el Abd 1970Bahrain Ain el Abd 1970Saudi Arabia Anna 1 Astro 1965Cocos Islands A...

110 DOS 1968New Georgia Islands(Gizo Island) Easter Island 1967Easter Island European 1950Mean for Austria,Belgium, Denmark,Finland, France, WestGermany, Gibraltar,Greece, Italy,Luxembourg,Netherlands, Norway,Portugal, Spain, Sweden,Switzerland European 1950Mean for Austria,Denmark, France, WestGerm...

113 FCC Compliance This device complies with Part 15 of the U.S. FederalCommunications Commission (FCC) Rules. Operation is subjectto the following two conditions: (1) this device may not causeharmful interference, and (2) this device must accept anyinterference received, including interference that...

115 Overlay Data To change the digital data shown on top of the Map Page: To select data for display: 1. From the Map page, press MENU | ↓ to O VERLAY D ATA | ENT . 2. Press ↓ or ↑ to select Data Type | ENT . Overlay Data command on the Map Menu, at left. Overlay Data Shown selection menu, right. In...

116 Tip: If you wish, you can change the displayed data font size when youselect a data type: 1. From the Map page, press MENU | ↓ to O VERLAY D ATA | ENT . 2. Press ↓ or ↑ to select Data Type |press → or ← to select Data Size | ENT . The data will be shown in the new font size. To return to theprev...

118 DATABASES LIMITED WARRANTY "We", "our", or "us" refers to Lowrance Electronics, Inc., the manufacturer ofthis product. "You" or "your" refers to the first person who purchases theproduct as a consumer item for personal, family, or household use. TheDatabas...

119 LOWRANCE ELECTRONICS FULL ONE-YEAR WARRANTY "We," "our," or "us" refers to LOWRANCE ELECTRONICS, INC., the manufacturer ofthis product. "You" or "your" refers to the first person who purchases this product as aconsumer item for personal, family or househol...

120 How to Obtain Service… …in the USA: We back your investment in quality products with quick, expert serviceand genuine Lowrance parts. If you're in the United States and youhave technical, return or repair questions, please contact the FactoryCustomer Service Department. Before any product can be...

Accessory Ordering Information for all countries To order Lowrance GPS accessories such as computer cables or MMC cards, please contact: 1) Your local marine dealer or consumer electronics store. Most quality dealers that handle marine electronic equipment or other consumer electronics should be abl...