Link Electronics Door phone - Manual

Page 3 - Basic description; SlimDoorPhone models; Three versions are available :; Installation

3 1. Basic description 1.1 Features ¾ Very slim module for surface mounting only. Supplied in 1, 2 or 4 button variants. ¾ Voice communication powered from analogue telephone line only. ¾ Pulse and tone (DTMF) dial ¾ Two 16 digits numbers saved under each button (includes *, #, RECALL and pause) ¾ D...

Page 4 - COM; NC

4 2.1.2 Uncover control elements 4. Push the aluminium speaker grille down (see figure – 4). 2.1.3 Wiring and wall mounting 5. Use the wall mounting template at the end of the manual to mark the position for the screw holes and cable connection on the mounting surface. Drill the holes. 6. Feed the c...

Page 6 - Location of ID Doorphone components

6 2.2 Location of ID Doorphone components All mounting, control and setting elements are located under the speaker front aluminium grille. . PC connector SlimDoorPhone fixing screw hole Service switch Loudspeaker MIC-setting of microphone volume TRH –setting of microphone activation level SPK- setti...

Page 8 - SlimDoorPhone Services; Signalling Overview; Condition Tones; Visitor at the door; mode; Telephone Caller

8 3 SlimDoorPhone Services 3.1 Signalling Overview The unit signals acoustic conditions that may occur during operation. You can listen to the signalling samples in the ID Manager program. Condition Tones Tone frequency Pick up line – ▄ – ■ – ▀ – 425-850-1275 Hang up line – ▀ – ■ – ▄ 1275-850-425 Co...

Page 9 - Parameter programming; Programming from a telephone by DTMF

9 dialled to close the relay ( parameter 35 ), releasing the lock. Hanging up the telephone will end the call, as will the busy tone from the PBX. 3.3.2 Incoming call An incoming call is a call to the unit. After dialling the PBX extension number to which the unit is connected, the unit will ring fo...

Page 10 - Programming from a PC – ID Manager program; Parameter description; Direct Dialling – Memories

10 4.2 Programming from a PC – ID Manager program To setup the unit from a PC you will require a special USB tool cable, available separately, and must first install the USB driver and ID Manager software. Refer to the CD for more details. The unit must also be connected to the telephone line. Proce...

Page 12 - Basic parameters; Time parameters

12 5.3 Basic parameters Parameter Value Description Default Exam.1 Exam.2 41 v Dialling type 0 0 0 v – dial type v=0 is DTMF tone dial, v=1 is pulse dial Parameter Value Description Default Exam.1 Exam.2 42 z Prolong call ∗ ∗ ∗ z – button for call prolongation ∗ or # (10 sec before Maximum Call Dura...

Page 15 - Overview of Parameters

15 z=3 – all tones are active – ( default) It is possible to generate an audible signal (only in mode m=1) to alert visitors that the door is unlocked so that they can enter. This is especially useful when using a DC power source, as lock release may be silent. z=8 – signalling is active z=9 – signa...

Page 16 - Technical parameters; Electrical parameters; Parameter Value; Mechanical dimensions

16 50 p Pause duration (ms) 8 (800ms) 8 (800ms) 8 (800ms) 6# s Number of fitted buttons on basic module 6* t Delay of line connection (Siemens PBX) 1 1 1 6 z Acoustic signalling 3 and 9 3 and 9 3 and 9 8# # Default setting executes 8# 1 Setting per exam. 1 executes 8# 2 Setting per exam. 2 executes ...

Page 17 - Table for easy programming

17 7 Table for easy programming Complete the values you want to program in the empty part of table on the next page. All programming commands are located in the double-framed area, to simplify programming. Retain a copy for future reference. Use Programming sequence Description Detail par. Fill valu...

Page 18 - Drilling master board