Lincoln 2010 MKZ - Manual

SAFETY AND ENVIRONMENT PROTECTION Warning symbols in this guide How can you reduce the risk of personal injury to yourself or others? Inthis guide, answers to such questions are contained in commentshighlighted by the warning triangle symbol. These comments should beread and observed. Warning symbol...

Service Data Recording Service data recorders in your vehicle are capable of collecting andstoring diagnostic information about your vehicle. This potentiallyincludes information about the performance or status of various systemsand modules in the vehicle, such as engine, throttle, steering or brake...

To access this information, special equipment must be directly connectedto the recording modules. Ford Motor Company and Ford of Canada donot access event data recorder information without obtaining consent,unless pursuant to court order or where required by law enforcement,other government authorit...

Export unique (Non–United States/Canada) vehicle specificinformation For your particular global region, your vehicle may be equipped withfeatures and options that are different from the features and options thatare described in this Owner’s Guide. A market unique supplement may be supplied that comp...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Parking Brake System Brake Fluid -Non-Petroleum Based P...

WARNING LIGHTS AND CHIMES Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause extensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Many lights will illuminate when you start your vehicle to make ...

Solid illumination after the engine is started indicates the On BoardDiagnostics System (OBD-II) has detected a malfunction. Refer to On board diagnostics (OBD-II) in the Maintenance and Specifications chapter. If the light is blinking, engine misfire is occurring which coulddamage your catalytic co...

AdvanceTrac 威 /Traction Control™: Illuminates when the AdvanceTrac 威 /Traction Control™ is active. If the light remains on, havethe system serviced immediately,refer to the Driving chapter for more information. AdvanceTrac 威 /Traction Control™ off light: Illuminates when the AdvanceTrac 威 /Traction ...

GAUGES Speedometer: Indicates the current vehicle speed. Engine coolant temperaturegauge: Indicates engine coolant temperature. At normal operatingtemperature, the needle will be inthe normal range (between “H” and“C”). If it enters the red section, the engine is overheating. Stopthe vehicle as soon...

Fuel gauge: Indicates approximately how much fuel is leftin the fuel tank (when the ignitionis in the on position). The fuelgauge may vary slightly when thevehicle is in motion or on a grade. The FUEL icon and arrow indicateswhich side of the vehicle the fuelfiller door is located. Refer to Filling ...

display features on the message center for a display of status. Thesystem will also notify you of potential vehicle problems with a display ofsystem warnings followed by a long indicator chime. Selectable features Reset Press this control to select and resetfunctions shown in the INFO menuand SETUP ...

Language 1. Select this function from theSETUP menu for the currentlanguage to be displayed. 2. Waiting four seconds or pressingthe RESET control cycles themessage center through each of the language choices. Selectable languages are English, Spanish, or French. 3. Press and hold the RESET control f...

TO STOP ALARM START VEHICLE — Displayed when the perimeter alarm system is armed and the vehicle is entered using the key on thedriver’s side door. In order to prevent the perimeter alarm system fromtriggering, the ignition must be turned to Start before the 12 secondchime expires. See Perimeter ala...

AUDIO SYSTEMS AM/FM in-dash CD6/MP3 satellite compatible Lincoln premiumsound/THX audio system WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device that may take theirfocus off th...

Satellite Radio Satellite radio is available only with a valid SIRIUS radiosubscription. Check with your authorized dealer for availability. SIRIUS: Press repeatedly to access satellite radio mode, if equipped. Press repeatedly to cycle through SAT1, SAT2 and SAT3 modes. TUNE: Turn to go to the next...

Note: Separate categories can be set for SAT1, SAT2 or SAT3. Refer to Satellite radio menu for further information on selecting a satellite radio category. SATELLITE RADIO MENU: Press MENU when satellite radio mode is active to access. Press OK to enter into the satellite radio menu.Press SEEK to cy...

c. DELETE ALL SONGS: Press OK to delete all song’s from the system’s memory. The display will read ARE YOU SURE ? Press OK toconfirm deletion of all saved songs and the display will read ALLDELETED. Note: If there are no songs presently saved, the display will read NO SONGS. d. DISABLE ALERTS/ENABLE...

TREBLE: Press SEEK to adjust the level of treble. BALANCE: Press SEEK to adjust the audio between the left (L) and right (R) speakers. FADE: Press SEEK to adjust the audio between the back (B) and front (F) speakers. SPEED COMPENSATED VOLUME: With this feature on, radio volume automatically gets lou...

Auxiliary input jack (Line in) WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device that may take theirfocus off the road. The driver’s primary responsibility is the safeoperation...

5. Turn the portable music player on and adjust the volume to 1/2 thevolume. 6. Press AUX on the vehicle radio repeatedly until LINE, LINE IN orSYNC LINE IN appears in the display.You should hear audio from your portable music player, although it maybe low. 7. Adjust the sound on your portable music...

Your vehicle is equipped with a USBport inside your center console. Thisfeature allows you to plug in mediaplaying devices, memory sticks, andalso to charge devices if theysupport this feature. For furtherinformation on this feature, refer to Accessing and using your USBport in the SYNC supplement o...

CD/CD player care: Do: • Handle discs by their edges only. Never touch the playing surface. • Inspect discs before playing. Clean only with an approved CD cleanerand wipe from the center out. Don’t: • Expose discs to direct sunlight or heat sources for extended periodsof time. • Clean using a circul...

• Terrain: Hills, mountains, tall buildings, bridges, tunnels, freewayoverpasses, parking garages, dense tree foliage and thunderstorms caninterfere with your reception. • Station overload: When you pass a ground based broadcast repeatingtower, a stronger signal may overtake a weaker one and result ...

DUAL AUTOMATIC TEMPERATURE CONTROL (DATC) SYSTEMWITH HEATED AND COOLED SEATS Temperature conversion: To switch between Fahrenheit and Celsius, refer to Message center in the Instrument Cluster chapter. 1. + Fan speed control: Press to increase the fan speed. 2. Defrost: Distributes outside air throu...

DUAL ZONE AUTOMATIC TEMPERATURE CONTROL WITHHEATED AND COOLED SEATS(NAVIGATION BASED – IF EQUIPPED) Temperature conversion: To switch between Fahrenheit and Celsius, refer to Message center in the Instrument Cluster chapter. 1. CLIMATE: Press to control the climate control system through the touch d...

VOICE COMMANDS IN CLIMATE MODE Please refer to the Voice commands in climate mode section of the Navigation supplement for more information on using voice commands with the climate control system. Operating tips • To reduce fog build up on the windshield during humid weather,select (defrost). • To r...

To aid in side window defogging/demisting in cold weather: 1. Select . 2. Select A/C. 3. Adjust the temperature control to maintain comfort. 4. Set the fan speed to the highest setting. 5. Direct the outer instrument panel vents towards the side windows. To increase airflow to the outer instrument p...

HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps, licenseplate lamps and tail lamps. Turns the low beam headlamps on. Adaptive headlamps (if equipped) The headlamp beams move in the same direction as the steering wheelto provide more visibility when driving ar...

Autolamps - Programmable exit delay Programmable exit delay allows the length of the autolamp exit delay tobe changed. To program the auto lamp exit time delay: 1. Start with the ignition in the off position and the headlamp control inthe autolamp position. 2. Turn the headlamp control to off. 3. Tu...

WARNING: Always remember to turn on your headlamps at dusk or during inclement weather. The Daytime Running Lamp (DRL) system does not activate the tail lamps and generally may notprovide adequate lighting during these conditions. Failure to activateyour headlamps under these conditions may result i...

• Press and hold the top or bottom of the control until the desiredlighting level is reached. • Press and hold the top of the control to the full on position to activatethe “dome on” feature. This will turn on the interior courtesy lights.The lights will remain on until the bottom of the control is ...

4. On the wall or screen you willobserve an area of high intensitylight. The top of the high intensityarea should touch the horizontalreference line, if not, the beam willneed to be adjusted using the nextstep. 5. Locate the vertical adjuster oneach headlamp. Using a Phillips #2screwdriver, turn the...

Welcome and farewell lighting are included in the Lincoln white signaturecolor. The transition from signature color to ambient occurs when thekey is placed in the ignition and all doors are closed. Farewell lightingoccurs when the key is removed from the ignition and the driver door isopened. Note: ...

Replacing headlamp bulbs High beam/low beam bulb replacement For driver side replacement of the high beam/low beam bulbs, do thefollowing: 1. Make sure the headlamp switch is in the off position, then open thehood. 2. Reach over the front bolster and remove the rubber bulb access coverfrom the headl...

Replacing front parking lamp/turn signal bulb For driver side replacement of the front parking lamp/turn signalbulb, do the following: WARNING: To reduce the risk of vehicle damage and/or personal burn injuries do not start your engine with the air cleaner removed and do not remove it while the engi...

MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you toincrease the speed of the wipers;rotate toward you to decrease thespeed of the wipers. Rain sensing wipers (ifequipped): The rain sensing wipers will automatically activate whenmoisture is present on thewindshield a...

Windshield wiper rainlamp feature When the windshield wipers are turned on during daylight, and theheadlamp control is in the autolamp position, the exterior lamps will turnon after a brief delay and will remain on until the wipers are turned off. TILT/TELESCOPE STEERING WHEEL To adjust the steering...

Slide on rod feature Rotate the visor towards the sidewindow and extend it rearward foradditional sunlight coverage. Note: To stow the visor back into the headliner, visor must beretracted before moving it backtowards the windshield. OVERHEAD CONSOLE The appearance of your vehicle’s overhead console...

degrees between adjacent zones and will become noticeable as thevehicle crosses multiple zones. A correct zone setting will eliminate thiserror. Refer to Compass calibration adjustment. Compass zone adjustment 1. Determine which magnetic zoneyou are in for your geographiclocation by referring to the...

2. To calibrate, press and hold the 7and 9 radio preset buttons togetherfor approximately 10 seconds untilCAL appears. Release the buttons. 3. Slowly drive the vehicle in acircle (less than 3 mph [5 km/h])until the CAL display changes to thedirection value (N, S, E, W, etc.). Itmay take up to five c...

The auxiliary power point is located in the center console utilitycompartment. Do not use the power point for operating the cigarette lighter element (ifequipped). To prevent the fuse from being blown, do not use the power point(s)over the vehicle capacity of 12 VDC/180W. If the power point or cigar...

WARNING: When closing the power windows, you should verify they are free of obstructions and ensure that children and/or pets are not in the proximity of the window openings. Press and pull the switches to openand close windows. • Push down (to the first detent)and hold the switch to open. • Pull up...

INTERIOR MIRROR The interior rear view mirror has two pivot points on the support armwhich lets you adjust the mirror UP or DOWN and from SIDE to SIDE. WARNING: Do not adjust the mirror while the vehicle is in motion. Automatic dimming interior rear view mirror Your vehicle is equipped with aninteri...

To adjust your mirrors: 1. Rotate the control clockwise toadjust the right mirror and rotatethe control counterclockwise toadjust the left mirror. 2. Move the control in the directionyou wish to tilt the mirror. 3. Return to the center position to lock mirrors in place. Memory feature The power side...

Setting speed control The controls for using your speedcontrol are located on the steeringwheel for your convenience. 1. Press the ON control and releaseit. 2. Accelerate to the desired speed. 3. Press the SET + or SET - controland release it. 4. Take your foot off the acceleratorpedal. 5. The indic...

Turning off speed control There are two ways to turn off the speed control: • Depress the brake pedal. This willnot erase your vehicle’spreviously set speed. • Press the speed control OFFcontrol. Note: When you turn off the speed control or the ignition, your speedcontrol set speed memory is erased....

For further information on the Navigation system/SYNC system, refer tothe Navigation and SYNC supplements. MOON ROOF (IF EQUIPPED) You can move the glass panel of the moon roof back to open or tilt up(from the closed position) to ventilate the vehicle. WARNING: Do not let children play with the moon...

is released to the neutral position, then held in the one-touch positionwithin two seconds after the moon roof reaches the bounce-backposition, the moon roof will travel with no bounce-back protection. If the control is released before the moon roof reaches fully closed or theignition is turned off ...

Do not use the HomeLink 威 Wireless Control System with any garage door opener that lacks safety stop and reverse features as required byU.S. federal safety standards (this includes any garage door openermodel manufactured before April 1, 1982). A garage door which cannotdetect an object, signaling t...

• Continue to press and hold the HomeLink 威 button (note Step 2 in the Programming section) while you press and release — every two seconds (“cycle”) your hand-held transmitter until the frequency signal has been accepted by the HomeLink 威 . The indicator light will flash slowly and then rapidly aft...

Reprogramming a single HomeLink 姞 button To program a device to HomeLink 威 using a HomeLink 威 button previously trained, follow these steps: 1. Press and hold the desired HomeLink 威 button. Do NOT release the button. 2. The indicator light will begin to flash after 20 seconds. Withoutreleasing the H...

KEYS Your vehicle is equipped with twoIntegrated Keyhead Transmitters(IKTs). The IKT functions as both aprogrammed ignition key thatoperates all the locks and starts thevehicle, and a remote entrytransmitter. Your IKTs are programmed to your vehicle; using a non-programmed keywill not permit your ve...

Recommended handling of the Integrated Keyhead Transmitter(IKT) To avoid inadvertently activating the remote entry functions of yourvehicle, it is recommended that the Integrated Keyhead Transmitter(IKT) be handled properly when starting and turning off your vehicle. When inserting the IKT into thei...

Keyless entry keypad procedure 1. Turn the ignition to the offposition. 2. Close all the doors. 3. Enter factory–set 5–digit entrycode. 4. Press and hold the 3 • 4. While holding the 3 • 4 press the 7 • 8. 5. Release the 7 • 8. 6. Release the 3 • 4. The user should receive a horn chirp to indicate t...

2. Press and release again within five seconds to unlock all the doors. The remote entry system activates the illuminated entry feature; thisfeature turns on the lamps for 25 seconds or until the ignition is turnedto the on position. The inside lights will not turn off if: • they have been turned on...

Note: The panic alarm will only operate when the ignition is in the off position. Opening the trunk Press twice within three seconds to open the trunk. • Ensure that the trunk is closed and latched before driving yourvehicle. Failure to properly latch the trunk may cause objects to fallout or block ...

3. A tone will be heard when the deactivation is complete.4. Repeat this procedure for another transmitter if desired. Replacing the battery The Integrated Keyhead Transmitter uses one coin type three-voltlithium battery CR2032 or equivalent. To replace the battery: 1. Twist a thin coin in the slot ...

system section of this chapter. Note: At least two IKTs are required to perform this procedure yourself. Illuminated entry The interior lamps and puddle lamps (if equipped) illuminate when theIntegrated Keyhead Transmitter or the keyless entry system keypad isused to unlock the door(s). The illumina...

the ignition is in the 1 (off) position and all vehicle doors are closed. Youmust complete Steps 1–5 within 30 seconds or the procedure will haveto be repeated. If the procedure needs to be repeated, wait a minimumof 30 seconds before beginning again. 1. Place the key in the ignition andturn the ign...

• The battery saver will shut off the headlamps 10 minutes after theignition has been turned to the 1 (off) position. SECURICODE™ KEYLESS ENTRY SYSTEM You can use the keyless entrykeypad to: • lock or unlock the doors withoutusing a key. • open the trunk. • recall memory seat/power mirrors positions...

Erasing personal code 1. Enter the factory set 5–digit code. 2. Within five seconds, press the 1 • 2 on the keypad and release. 3. Press and hold the 1 • 2 for two seconds. This must be done within five seconds of completing Step 2. All personal codes are now erased and only the factory set 5–digit ...

Automatic arming The vehicle is armed immediately after switching the ignition to the offposition. The theft indicator will flash everytwo seconds to act as a theftdeterrent when the vehicle isarmed. Automatic disarming The vehicle is disarmed immediately after the ignition is turned to the onpositi...

If the key was not successfully programmed, it will not start yourvehicle’s engine and/or will not operate the remote entry features. Thetheft indicator light may flash on and off. Wait 20 seconds and you mayrepeat Steps 1 through 8. If failure repeats, bring your vehicle to yourauthorized dealer to...

• Press the 7 • 8 and 9 • 0 controls on the keyless entry padat the same time to lock thedoors (driver’s door must beclosed). There is a 20 second countdown when any of the above actions occurbefore the vehicle becomes armed. Each door, the hood or the trunk is armed individually, and if any areopen...

SEATING WARNING: Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the event of a collision. WARNING: Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop. WARNING: Before ret...

WARNING: To minimize the risk of neck injury in the event of a crash, head restraints must be installed properly. Adjusting the front power seat WARNING: Never adjust the driver’s seat or seatback when the vehicle is moving. WARNING: Do not pile cargo higher than the seatbacks to reduce the risk of ...

Move the switch in the direction ofthe arrows to raise or lower thefront portion of the seat cushion. Move the switch in the direction ofthe arrows to raise or lower the rearportion of the seat cushion. Press the switch in the direction ofthe arrows to move the seatforward, backward, up or down. Pow...

Using the power lumbar support The power lumbar control is located on the outboard side of the seat. Press one side of the control toadjust firmness. Press the other side of the controlto adjust softness. Memory seat and mirrors This system allows automaticpositioning of the driver seat andmirrors t...

• DATC system • Navigation-based system The cooled seats will turn off after 30 minutes. If the engine falls below 350 RPMs while the cooled seats are on, thefeature will turn itself off and will need to be reactivated. Climate controlled seats air filter replacement (if equipped) The climate contro...

• Remove filter. To install a filter: • First, position the filter in it’shousing making sure that the farforward end is all the way up inthe housing. Then push in on thecenter of the outside edge of thefilter and rotate up into thehousing until it clips into position. REAR SEATS Second-row adjustab...

The adjustable head restraintsconsist of: • a trimmed energy absorbing foamand structure (1), • two steel stems (2), • a guide sleeve adjust/releasebutton (3), • and a guide sleeve with a pin holefor removing the head restraint(4). To adjust the head restraint, do the following: 1. Raise the head re...

To reinstall the adjustable head restraint, do the following: 1. Insert the two stems into theguide sleeve collars. 2. Push the head restraint downuntil it locks. Properly adjust the head restraint so that the top of the head restraint iseven with the top of your head and positioned as close as poss...

to the airbag when it begins to inflate. For some occupants, this occursbecause they are initially sitting very close to the airbag. For otheroccupants, this occurs when the occupant is not properly restrained bysafety belts or child safety seats and they move forward during pre-crashbraking. The mo...

Front safety belt energy management retractors The front outboard safety belt energy management retractors allowwebbing to be pulled out of the retractor in a gradual and controlledmanner in response to the occupant’s forward momentum. This helpsreduce the risk of force-related injuries to the occup...

Combination lap and shoulder belts 1. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) until you hear a snap and feelit latch. Make sure the tongue issecurely fastened in the buckle. 2. To unfasten, push the releasebutton and remove the tongu...

All safety restraints in the vehicle are combination lap and shoulderbelts. All of the passenger combination lap and shoulder belts have twotypes of locking modes described below: Vehicle sensitive mode This is the normal retractor mode, which allows free shoulder belt lengthadjustment to your movem...

• Grasp the shoulder portion andpull downward until the entirebelt is pulled out. • Allow the belt to retract. As the belt retracts, you will hear a clickingsound. This indicates the safety belt is now in the automatic lockingmode. How to disengage the automatic locking mode WARNING: Ford Motor Comp...

WARNING: Position the safety belt height adjusters so that the belt rests across the middle of your shoulder. Failure to adjust the safety belt properly could reduce the effectiveness of the safetybelt and increase the risk of injury in a collision. Safety belt pretensioner Your vehicle is equipped ...

Conditions of operation If... Then... The driver’s safety belt is notbuckled before the ignitionswitch is turned to the onposition... The safety belt warning lightilluminates 1-2 minutes and thewarning chime sounds 4-8 seconds. The driver’s safety belt isbuckled while the indicatorlight is illuminat...

The following are reasons most often given for not wearing safety belts(All statistics based on U.S. data): Reasons given... Consider... “Crashes are rare events” 36700 crashes occur every day. The more we drive, the more we areexposed to “rare” events, even forgood drivers. 1 in 4 of us will be ser...

Reasons given... Consider... “I have an airbag” Airbags offer greater protection whenused with safety belts. Frontal airbagsare not designed to inflate in rear andside crashes or rollovers. “I’d rather be thrown clear” Not a good idea. People who are ejected are 40 times more likelyto DIE. Safety be...

AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) The passenger airbag cover is a seamless design so that you cannot seethe boundary around its door. The shaded area in the illustrationrepresents the passenger airbag cover. WARNING: Do not put anything on or over the airbag cover. Placing objects on or ove...

Children and airbags Children must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rearseating positions than in the frontseating position. Failure to followthese instructions may increase therisk of injury in a collision. WARNING: Airb...

The airbags inflate and deflaterapidly upon activation. After airbagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt propellant. This mayconsist of cornstarch, talcumpowder (to lubricate the bag) orsodium compounds (e.g., bakingsoda) that result from thecombustion pr...

In case there is a problem with thefront passenger sensing system, theairbag readiness light in theinstrument cluster will stay lit. If the airbag readiness light is lit, do the following: The driver and/or adult passengers should check for any objects thatmay be lodged underneath the front passenge...

A difficulty with the system is indicated by one or more of the following: • The readiness light (same lightfor front and side airbag system)will either flash or stay lit. • The readiness light will notilluminate immediately after ignition is turned on. • A series of five beeps will be heard. The to...

WARNING: If the side airbag has deployed, the airbag will not function again.The side airbag system(including the seat) must beinspected and serviced by anauthorized dealer. If the airbag is not replaced, the unrepairedarea will increase the risk of injuryin a collision. Determining if the system is...

WARNING: Do not place objects or mount equipment on or near the side air curtain cover. WARNING: Do not lean your head on the door. The side airbag could injure you as it deploys from the seat. WARNING: Do not attempt to service, repair, or modify the side air curtain system, its fuses, the A, B, or...

The feature will continue to operate until the vehicle runs out of power. Disposal of airbags and airbag equipped vehicles(including pretensioners) Contact your authorized dealer as soon as possible. Airbags MUST BEdisposed of by qualified personnel. SAFETY RESTRAINTS FOR CHILDREN See the following ...

Recommendations for Safety Restraints for Children Child size, height, weight, or age Recommendedrestraint type Infantsortoddlers Children weighing 40 lb (18 kg) or less(generally age four or younger) Use a child safetyseat (sometimescalled an infantcarrier, convertibleseat, or toddlerseat). Smallch...

WARNING: Always carefully follow the instructions and warnings provided by the manufacturer of any child restraint to determine if the restraint device is appropriate for your child’s size,height, weight, or age. Follow the child restraint manufacturer’sinstructions and warnings provided for install...

training to ensure that all children ages 0 to 16 are properly restrained inthe correct restraint system. Ford recommends checking with a NHTSACertified Child Passenger Safety Technician (CPST) and yourpediatrician to make sure your seat is appropriate for your child andproperly installed in the veh...

WARNING: The standardized spacing for LATCH lower anchors is 280 mm (11 inches) center to center. Do not use LATCH lower anchors for the center seating position unless the child seatmanufacturer’s instructions permit and specify using anchors spaced atleast as far apart as those in this vehicle. If ...

The tether strap anchors in yourvehicle are in the following positions(shown from top view): Attach the tether strap only to the appropriate tether anchor as shown.The tether strap may not work properly if attached somewhere otherthan the correct tether anchor. Once the child safety seat has been in...

4. Clip the tether strap to theanchor as shown. If the tether strap is clippedincorrectly, the child safety seat maynot be retained properly in theevent of a collision. 5. Tighten the child safety seat tether strap according to themanufacturer’s instructions. If the safety seat is not anchored prope...

The importance of shoulder belts Using a booster without a shoulder belt increases the risk of a child’shead hitting a hard surface in a collision. For this reason, you shouldnever use a booster seat with a lap belt only. It is generally best to use abooster seat with lap/shoulder belts in the back ...

INFORMATION ABOUT UNIFORM TIRE QUALITY GRADING Tire Quality Grades apply to newpneumatic passenger car tires. TheQuality grades can be found whereapplicable on the tire sidewallbetween tread shoulder andmaximum section width. Forexample: • Treadwear 200 Traction AA Temperature A These Tire Quality G...

WARNING: Under-inflation is the most common cause of tire failures and may result in severe tire cracking, tread separation or ⬙ blowout ⬙ , with unexpected loss of vehicle control and increased risk of injury. Under-inflation increases sidewall flexing and rollingresistance, resulting in heat build...

Note: If you have to drive a distance to get air for your tire(s), check and record the tire pressure first and add the appropriate air pressurewhen you get to the pump. It is normal for tires to heat up and the airpressure inside to go up as you drive. 2. Remove the cap from the valve on one tire, ...

Improper or inadequate vehicle maintenance can cause tires to wearabnormally. Inspect all your tires, including the spare, frequently, andreplace them if one or more of the following conditions exist: Tire wear When the tread is worn down to1/16th of an inch (2 mm), tires mustbe replaced to help pre...

U.S. DOT Tire Identification Number (TIN) Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the sidewall of all tires. Thisinformation identifies and describes the fundamental characteristics ofthe tire and also provides a U.S. DOT Tire Identific...

WARNING: When mounting replacement tires and wheels, you should not exceed the maximum pressure indicated on the sidewall of the tire to set the beads without additional precautionslisted below. If the beads do not seat at the maximum pressureindicated, re-lubricate and try again.When inflating the ...

• Do not run over curbs or hit the tire against a curb when parking WARNING: If your vehicle is stuck in snow, mud, sand, etc., do not rapidly spin the tires; spinning the tires can tear the tire and cause an explosion. A tire can explode in as little as three to fiveseconds. WARNING: Do not spin th...

• Front Wheel Drive (FWD)/AllWheel Drive (AWD) vehicles(front tires at top of diagram) Sometimes irregular tire wear can be corrected by rotating the tires. Note: If your tires show uneven wear ask an authorized dealer to check for and correct any wheel misalignment, tire imbalance or mechanicalprob...

Information on “P” type tires P215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (Note thatthe tire size, load index and speedrating for your vehicle may bedifferent from this example.) 1. P: Indicates a tire, designated by the Tir...

12. Treadwear, Traction and Temperature Grades • Treadwear: The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on aspecified government test course. For example, a tire graded 150would wear one and one-half (1 1 ⁄ 2 ) times as well ...

Additional information contained on the tire sidewall for “LT” typetires “LT” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below. Note: Tire Quality Grades do not apply to this type of tire. 1. LT: Indicates a tire, designated by the Tire a...

Information on “T” type tires “T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. Tire Quality Grades donot apply ...

The Tire Pressure Monitoring System complies with part 15 of the FCCrules and with RSS-210 of Industry Canada. Operation is subject to thefollowing two conditions: (1) This device may not cause harmfulinterference, and (2) This device must accept any interference received,including interference that...

Low Tire PressureWarning Light Possible cause Customer Action Required Solid Warning Light Tire(s)under-inflated 1. Check your tire pressure toensure tires are properlyinflated; refer to Inflating your tires in this chapter. 2. After inflating your tires tothe manufacturer’srecommended inflationpres...

Low Tire PressureWarning Light Possible cause Customer Action Required Flashing WarningLight Spare tire in use Your temporary spare tire is in use. Repair the damaged roadwheel and re-mount it on thevehicle to restore systemfunctionality. For a descriptionof how the system functionsunder these condi...

Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Label on the B-Pillar or the edge of the driver’s door(vehicles exported outside the US and Canada may not have a TireLabel). Look for “THE COMBINED WEI...

Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload. GAWR (Gross Axle Weight Rating) – is the maximum...

WARNING: Do not use replacement tires with lower load carrying capacities than the original tires because they may lower the vehicle’s GVWR and GAWR limitations. Replacement tireswith a higher limit than the original tires do not increase the GVWRand GAWR limitations. WARNING: Exceeding any vehicle ...

you have been planning for the past 2 years. Measuring the inside ofthe vehicle with the rear seat folded down, you have room for12-100 lb. (45 kg) bags of cement. Do you have enough load capacityto transport the cement to your home? If you and your friend eachweigh 220 lb. (99 kg), the calculation ...

STARTING Positions of the ignition 1. Off— locks the gearshift leverand allows key removal. Thisposition also shuts the engine andall electrical accessories off. 2. Accessory— allows the electricalaccessories such as the radio tooperate while the engine is notrunning. 3. On— all electrical circuits ...

How to use the engine block heater Ensure the receptacle terminals are clean and dry prior to use. To cleanthem, use a dry cloth. Depending on the type of factory installed equipment, your engine blockheater will use .4 to 1.0 kilowatt-hours of energy per hour of use. Yourfactory installed block hea...

ABS warning lamp The ABS lamp in the instrumentcluster momentarily illuminateswhen the ignition is turned on. Ifthe light does not illuminate duringstart up, remains on or flashes, theABS may be disabled and may need to be serviced. Even when the ABS is disabled andthe ABS light is on, normal brakin...

• The brake pedal may feel stiffer than usual. Traction Control (TCS) Traction Control is a driver aid feature that helps your vehicle maintaintraction of the wheels, typically when driving on slippery and/or hillyroad surfaces, by detecting and controlling wheel spin. Excessive wheel spin is contro...

AdvanceTrac 威 Features Controlswitchfunctions “Sliding car” icon “Sliding car off” icon ESC Traction Control Default atstart-up Illuminated during bulb check Illuminated during bulb check Enabled Enabled Control switchpressedmomentarily Not illuminated Illuminated solid Enabled Disabled Control swit...

If the steering wanders or pulls, check for: • an improperly inflated tire • uneven tire wear • loose or worn suspension components • loose or worn steering components • improper steering alignment A high crown in the road or high crosswinds may also make the steeringseem to wander/pull. BRAKE-SHIFT...

AUTOMATIC TRANSMISSION OPERATION Understanding the gearshift positions of the 6–speed automatictransmission P (Park) This position locks the transmission and prevents the front wheels fromturning. To put your vehicle in gear: • Depress the brake pedal • Move the gearshift lever into the desired gear...

N (Neutral) With the gearshift lever in N (Neutral), the vehicle can be started and isfree to roll. Hold the brake pedal down while in this position. D (Drive) with Overdrive The normal driving position for the best fuel economy. Transmissionoperates in gears one through six. D (Drive) with Overdriv...

To manually downshift the transmission: 1. Move the gearshift lever forwardto (-). 2. Release the lever, and it willreturn to the M position. Thetransmission will downshift. To manually upshift thetransmission: 1. Move the gearshift lever rearwardinto (+). 2. Release the lever, and it willreturn to ...

The BLIS™ will trigger the alert for vehicles that enter your blind zonefrom the rear or merge in to the blind zone from the side. Vehicles thatyou pass, or a vehicle that enters the blind zone from the front, willtrigger the alert only after the vehicle is present in the blind zone forthree seconds...

Cross traffic alert (CTA) system operation The cross traffic alert system warnsthe driver of approaching vehicleswhen R (Reverse) is selected andthe vehicle is backing out of afront-in parking spot. It sounds aseries of tones and flashes theBLIS™ indicator found on theexterior mirror on the side of ...

Cross Traffic coverage also decreases when parking at shallow angles(refer to figure for approximate zone coverage areas [sensor obstructed to vehicle on left] ). CTA Detection Limitations: Due to the nature of radar technology, there may be certain instances where vehicles entering and exiting theb...

BLIS™-CTA on/off and disable operation The BLIS™ and/or the CTA can be turned off via the message center.Turning the BLIS™ off does not turn off the CTA and visa versa. If eitherthe BLIS™ or CTA is turned off, the systems will automatically turn backon at the next ignition key cycle. When either the...

ALL WHEEL DRIVE (AWD) SYSTEM (IF EQUIPPED) Your vehicle may be equipped with a full-time All Wheel Drive (AWD)system. The AWD system is an active system, meaning it not onlyresponds to wheel slip between the front and rear axles but also has theability to anticipate wheel slip and transfer torque to...

When driving through water, determine the depth; avoid water higherthan the bottom of the wheel rims (if possible) and proceed slowly. If theignition system gets wet, the vehicle may stall. Once through water, always try the brakes. Wet brakes do not stop thevehicle as effectively as dry brakes. Dry...

your vehicle is equipped with a four wheel anti-lock brake system (ABS),do not “pump” the brakes. Refer to the Brakes section of this chapter for additional information on the operation of the anti-lock brake system. Maintenance and Modifications The suspension and steering systems on your vehicle h...

ROADSIDE ASSISTANCE Getting roadside assistance To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24–hours, seven days a week • for the...

• towing of your disabled vehicle • emergency travel expense reimbursement • travel planning benefits In Canada, for uninterrupted Roadside Assistance coverage, you maypurchase extended coverage prior to your Basic Warranty’s RoadsideAssistance expiring. For more information and enrollment, contact1...

After an accident, if the engine cranks but does not start, this switchmay have been activated. The fuel pump shut-off switch islocated in the front passengerfootwell area in the right uppercorner. To reset the switch: 1. Turn the ignition to the offposition. 2. Check the fuel system for leaks. 3. I...

Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 2A Grey Grey — — — 3A Violet Violet — — — 4A Pink Pink — — — 5A Tan Tan — — — 7.5A Brown Brown — — — 10A Red Red — — — 15A Blue Blue — — — 20A Yellow Yellow Yellow ...

The fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Protected Circuits 1 30A Driver smart window motor 2 15A Brake on/off switch, Centerhigh-mounted stop lamp 3 15A Not used (Spare) 4 30A Passenger front smart windowmotor 5 10A Keypad illumination, Brake shiftinterlock 6 20A Turn sig...

Fuse/Relay Location Fuse Amp Rating Protected Circuits 39 — Not used 40 — Not used 41 G8VA relay Backup lamps 42 G8VA relay Left headlamps 43 G8VA relay A/C clutch 44 G8VA relay Right headlamps 45 15A** Injectors 46 15A** PCM 47 10A** General powertrain components,A/C clutch, back-up lamps 48 15A** ...

(TPMS) in the Tires, Wheels and Loading chapter. Replace the spare tire with a road tire as soon as possible. During repairing or replacing ofthe flat tire, have the authorized dealer inspect the TPMS sensor fordamage. WARNING: The use of tire sealants may damage your Tire Pressure Monitoring System...

• Use more than one dissimilar spare tire at a time • Use commercial car washing equipment • Try to repair the dissimilar spare tire Use of one of the dissimilar spare tires listed above at any one wheellocation can lead to impairment of the following: • Handling, stability and braking performance •...

Stopping and securing the vehicle 1. Park on a level surface, set the parking brake and activate the hazardflashers. 2. Place the gearshift lever in P (Park) and turn the engine off. Removing the spare tire and jack 1. Remove the carpeted load floorpanel located in the rear of thevehicle and remove ...

3. Put the jack in the jack locatornext to the tire you are changing.Turn the jack handle clockwise untilthe wheel is completely off theground. Note : To avoid structural damage to the vehicle, ensure that the jack iscentered between the two markings(1) on the bottom of the rockerflange. WARNING: To...

Stowing the wheel and jack 1. Fully collapse the jack and place it back in the storage area in thetrunk. 2. Replace the jack retention bolt to secure the jack. 3. Place the tire in the storage bin in the trunk. 4. Replace the cover plate and bolt. • When storing a flat road tire, flip the cover plat...

Note: Inspect the wheel pilot hole prior to installation. If there isvisible corrosion in wheel pilot hole,remove loose particles by wipingwith clean rag and apply grease.Apply grease only to the wheel pilothole surface by smearing a “dime”(1 square cm) sized glob of greasearound the wheel pilot sur...

Preparing your vehicle When the battery is disconnected or a new battery is installed, theautomatic transmission must relearn its shift strategy. As a result, thetransmission may have firm and/or soft shifts. This operation isconsidered normal and will not affect function or durability of thetransmi...

4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarburetor/fuel injection system. Note: Do not attach the negative (-) cable to fuel lines, engine rocker covers, the intake manifold or electrical components ...

Removing the jumper cables Remove the jumper cables in the reverse order that they wereconnected. 1. Remove the jumper cable from the ground metal surface. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2. Remove the jumper cable on the negative (...

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift or flatbedequipment. Do not tow with a slingb...

Emergency towing In case of a roadside emergency with a disabled vehicle (without accessto wheel dollies, car hauling trailer, or flatbed transport vehicle) yourvehicle (regardless of transmission powertrain configuration) can be flattowed (all wheels on the ground) under the following conditions: •...

GETTING THE SERVICES YOU NEED Warranty repairs to your vehicle must be performed by an authorizedFord, Lincoln, or Mercury dealer. While any authorized dealer handlingyour vehicle line will provide warranty service, we recommend youreturn to your selling authorized dealer who wants to ensure yourcon...

• Service specials and promotions. In Canada: Mailing Address (Ford vehicles) Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E4 Telephone 1-800-565-3673 (FORD) Online www.ford.ca Mailing Address (Lincoln vehicles) Lincoln CentreFord Motor Company...

The CAMVAP program is a straight-forward and relatively speedyalternative to resolve a disagreement when all other efforts to produce asettlement have failed. This procedure is without cost to you and isdesigned to eliminate the need for lengthy and expensive legalproceedings. In the CAMVAP program,...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3-A), which is availablefrom your authorized dealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can dis...

WAXING • Wash the vehicle first. • Do not use waxes that contain abrasives; use Motorcraft PremiumLiquid Wax (ZC-53-A), which is available from your authorized dealer,or an equivalent quality product. • Do not allow paint sealant to come in contact with any non-body(low-gloss black) colored trim, su...

vehicle’s glass or the wiper blades may be the cause. These may includehot wax treatments used by commercial car washes, water repellentcoatings, tree sap, or other organic contamination; these contaminantsmay cause squeaking or chatter noise from the blades, and streaking andsmearing of the windshi...

• Do not use household or glass cleaners as these may damage thefinish of the instrument panel, interior trim and cluster lens. WARNING: Do not use chemical solvents or strong detergents when cleaning the steering wheel or instrument panel to avoid contamination of the airbag system. If a staining l...

WARNING: Do not use cleaning solvents, bleach or dye on the vehicle’s safety belts, as these actions may weaken the belt webbing. WARNING: On vehicles equipped with seat-mounted airbags, do not use chemical solvents or strong detergents. Such products could contaminate the side-airbag system and aff...

FORD AND LINCOLN MERCURY CAR CARE PRODUCTS Your Ford or Lincoln Mercury authorized dealer has many qualityproducts available to clean your vehicle and protect its finishes. Thesequality products have been specifically engineered to fulfill yourautomotive needs; they are custom designed to complement...

SERVICE RECOMMENDATIONS To help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your authorized dealer canprovide the necessary parts and service. Check your Warranty Guide/Customer Infor...

OPENING THE HOOD 1. Inside the vehicle, pull the hoodrelease handle located under thebottom of the instrument panel nearthe steering column. 2. Go to the front of the vehicle andrelease the auxiliary latch that islocated under the front center ofthe hood. 3. Lift the hood and support it with the pro...

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meetsFord specification WSB-M8B16-A2.Do not use any special washer fluidsuch as windshield water repellenttype fluid or bug wash. They m...

Replace wiper blades at least once per year for optimum performance. Poor wiper quality can be improved by cleaning the wiper blades and thewindshield. Refer to Windows and wiper blades in the Cleaning chapter. To prolong the life of the wiper blades, it is highly recommended toscrape off the ice on...

6. Wipe the dipstick clean. Insertthe dipstick fully, then remove itagain. • If the oil level is within this range, the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below this mark, engine oil must be added to raise the level within thenormal operating range. 2010 MKZ (378) Owners ...

• If required, add engine oil to theengine. Refer to Adding engine oil in this chapter. • Do not overfill the enginewith oil. Oil levels above thismark may cause enginedamage. If the engine is overfilled, some oil must beremoved from the engine by anauthorized dealer. 7. Put the dipstick back in and...

Engine oil and filter recommendations Look for this certificationtrademark. Use SAE 5W-20 engine oil Only use oils “Certified For Gasoline Engines” by the AmericanPetroleum Institute (API). An oil with this trademark symbol conformsto the current engine and emission system protection standards and f...

BATTERY Your vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice. If your battery has a cover/shield, make sure it is reinstalledafter the battery has been cleaned or replaced. For longer, trouble-free operation, keep...

WARNING: Keep batteries out of reach of children. Batteries contain sulfuric acid. Avoid contact with skin, eyes or clothing. Shield your eyes when working near the battery to protect againstpossible splashing of acid solution. In case of acid contact with skin oreyes, flush immediately with water f...

• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recycling centerto find out more about recyclingautomotive batteries. ENGINE COOLANT Checking engine coolant The concentration and level of engine coolant sho...

When the engine is cold, check thelevel of the engine coolant in thereservoir. • The engine coolant should be at the “FULL COLD” level or within the“COLD FILL RANGE” as listed on the engine coolant reservoir(depending upon application). • Refer to scheduled maintenance information for service interv...

• Add Motorcraft Premium Gold Engine Coolant or equivalentmeeting Ford specification WSS-M97B51-A1. Refer to Maintenance product specifications and capacities in this chapter. Note: Use of Motorcraft Cooling System Stop Leak Pellets or an equivalent product meeting Ford specification WSS-M99B37-B6, ...

3. Step back while the pressure releases. 4. When you are sure that all the pressure has been released, use thecloth to turn it counterclockwise and remove the cap. 5. Fill the coolant reservoir slowly with the proper coolant mixture (seeabove), to within the “COLD FILL RANGE” or the “FULL COLD” lev...

Severe climates If you drive in extremely cold climates (less than –34°F [–36°C]): • It may be necessary to increase the coolant concentrationabove 50%. • NEVER increase the coolant concentration above 60%. • Increased engine coolant concentrations above 60% willdecrease the overheat protection char...

• The symbol will illuminate. If the engine reaches a preset over-temperature condition, the enginewill automatically switch to alternating cylinder operation. Each disabledcylinder acts as an air pump and cools the engine. When this occurs the vehicle will still operate. However: • The engine power...

clothing and wash skin thoroughly with soap and water. Repeated orprolonged skin contact with fuel liquid or vapor causes skin irritation. • Be particularly careful if you are taking “Antabuse” or other forms ofdisulfiram for the treatment of alcoholism. Breathing gasoline vapors,or skin contact cou...

• DO NOT use a device that would hold the fuel pump handle in the fillposition. Easy Fuel™ “no cap” fuel system Your fuel tank is equipped with an Easy Fuel™ “no cap” fuel fillersystem. This allows you to simply open the fuel filler door and insert thefuel filler nozzle into the fuel system. The Eas...

WARNING: The fuel system may be under pressure. If you hear a hissing sound near the fuel filler door (Easy Fuel™ “no cap” fuel system), do not refuel until the sound stops. Otherwise, fuel mayspray out, which could cause serious personal injury. Choosing the right fuel Use only UNLEADED fuel or UNL...

could cause damage to the fuel system. Repairs to correct the effects ofusing an aftermarket product in your fuel may not be covered by yourwarranty. Many of the world’s automakers approved the World-Wide Fuel Charterthat recommends gasoline specifications to provide improvedperformance and emission...

WARNING: Do not try to pry open or push open the Easy Fuel™ system with foreign objects. This could damage the fuel system and its seal and cause injury to you or others. When filling the vehicle’s fuel tank from a portable fuel container, use theincluded funnel. 1. Locate the white plastic funnel. ...

The advertised capacity is the amount of the indicated capacity and theempty reserve combined. Indicated capacity is the difference in theamount of fuel in a full tank and a tank when the fuel gauge indicatesempty. Empty reserve is the small amount of fuel remaining in the fueltank after the fuel ga...

Keep a record for at least one month and record the type of driving (cityor highway). This will provide an accurate estimate of the vehicle’s fueleconomy under current driving conditions. Additionally, keeping recordsduring summer and winter will show how temperature impacts fueleconomy. In general,...

• Perform all regularly scheduled maintenance items. Follow therecommended maintenance schedule and owner maintenance checksfound in scheduled maintenance information. Conditions • Heavily loading a vehicle may reduce fuel economy at any speed. • Carrying unnecessary weight may reduce fuel economy (...

indicate that the vehicle is not ready for I/M testing. To determine if thevehicle is ready for I/M testing, turn the ignition key to the on positionfor 15 seconds without cranking the engine. If the Service engine soon indicator blinks eight times, it means that the vehicle is not ready for I/M tes...

BRAKE FLUID The fluid level will drop slowly asthe brakes wear, and will rise whenthe brake components are replaced.Fluid levels between the “MIN” and“MAX” lines are within the normaloperating range; there is no need toadd fluid. If the fluid levels areoutside of the normal operatingrange the perfor...

Note: Only one ATF fluid specification has been tested and approved for use with the automatic 6-speed: Premium Automatic Transmission fluid.Mercon fluids cannot be used with the automatic 6-speed withoutdamage or voiding warranty. Use of a non-approved automatic transmission fluid may causeinternal...

The Vehicle Identification Number (VIN) contains the followinginformation: 1. World manufacturer identifier 2. Brake system / Gross VehicleWeight Rating (GVWR) / RestraintDevices and their location 3. Make, vehicle line, series, bodytype 4. Engine type 5. Check digit 6. Model year 7. Assembly plant ...

GENUINE LINCOLN ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Lincoln Accessories are available for yourvehicle through your local Lincoln or Ford of Canada dealer. Thesequality accessories have been specifically engineered to fulfill yourautomotive needs; they are custom designed to comp...

Peace of mind Remote start Vehicle security systems Wheel locks For maximum vehicle performance, keep the following information inmind when adding accessories or equipment to your vehicle: • When adding accessories, equipment, passengers and luggage to yourvehicle, do not exceed the total weight cap...

FORD ESP EXTENDED SERVICE PLANS More than 30 million Ford, Lincoln, and Mercury owners have discoveredthe powerful protection of Ford ESP. It is the only extended service planbacked by Ford Motor Company, and provides “peace of mind”protection beyond the New Vehicle Limited Warranty coverage. Up to ...

A Accessory delay ..........................75 AdvanceTrac ..............................205 Air cleaner filter ...............300–301 Air conditioning ..........................45 automatic temperaturecontrol system ..........................48 Airbag supplemental restraintsystem .....................

Parts (see Motorcraft parts) ....301 Passenger OccupantClassification Sensor .................124 Power distribution box(see Fuses) ...............................238 Power door locks ........................90 Power mirrors .............................76 Power point ..................................