Lincoln 1600 Series - Manual
Lincoln 1600 Series – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Global; Lincoln Impinger; Easy to Operate
- Page 3 – Gas Supply Pressure Recommendations:; Natural; Recommended Minimum Clearances:; All new impinger
- Page 4 – GAS; GAS; GAS; GAS; GAS
Global
1111 North Hadley Road
P.O. Box 1229
Fort Wayne, Indiana 46801-1229
Tel 1.260.459.8200
Fax 1.260.436.0735
E mail [email protected]
web www.lincolnfp.com
©2007 Lincoln Foodservice Products, Inc.
Printed in the U.S.A.
1256-2.5K-04/07-SP
Capacity Estimates | Pies Per Hour:
BAKE TIME
Pie Size
3 min.
3½ min.
4 min.
4½ min.
5 min.
5½ min.
6 min.
6½ min.
7 min.
12” (30 cm)
182
155
135
120
108
99
90
84
78
14” (36 cm)
115
99
87
88
69
63
58
53
50
16” (41 cm)
101
87
76
67
61
55
51
47
44
Ventilation Requirements:
Ventilation is required. Local codes prevail. These are the “authority having jurisdiction” as stated by the
National Fire Protection Association, Inc., in NFPA 96-1994. Estimates of CFM requirements can vary from
2400 to as high as 6000 CFM exhaust. In all cases the ambient temperature around the oven must not
exceed 95°F (35°C) when the oven is operating.
This information is shown as a guideline for ventilating
the Impinger
®
1600 Ovens.
18-24”
(457 mm -
610mm)
8”
(203 mm)
CAPTURE AREA
CAPTURE AREA
CAPTURE VELOCITY 50 FPM
CAPTURE
VELOCITY
50 FPM
78”
(1981 mm)
94” (2388 mm)
8”
(203 mm)
6”
(153 mm)
6”
(153 mm)
70” (1778 mm)
1. Dimensions shown are for ovens without long extension shelves.
The outside end of the conveyor
frame must be a minimum of eight (8) inches (203 mm) inside the canopy as shown.
2.
The capture velocity across the lower edge of the canopy is to be 50 FPM at sides and front.
3. Use filters at rear exhaust area of the hood, as shown. Do
not
just put an opening into a 4 sided canopy.
4. The ovens are to be centered in the canopy space left-to-right and front-to-back if possible.
5. A six (6) inch space at rear of oven is recommended for utilities.
6. Use of a Type I or Type II application and overall final installation is determined per local codes.
7.
Recommended 2400-3000 CFM exhaust
, typical, or higher per local codes; as a guideline to obtain
adequate capture velocity.
8.
Recommended 80% of make-up air provided outside of the canopy
through perforated metal dif-
fusers directed straight down...
not at the oven
; located at front , side or both.
9.
Room air diffusers must not be directed onto the oven and should be positioned a minimum of
three (3) feet from the perimeter of the hood to keep airflow from affecting the oven.
NOTE: Specifications subject to change without notification.
1600 S
er
ies | I
mpinger® L
ow P
rofile Single B
elt C
on
ve
yor
iz
ed O
ven
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Global 1600 Series Impinger® Low Profile Single Belt Conveyorized Oven Lincoln Impinger ® Conveyor O vens are the premier continuous cook platform for the food ser vice industr y. Using the latest advancements in air impingement technology, Impinger ® O vens allow for rapid heating, cook ing, bak in...
Global Gas Supply Pressure Recommendations: Gas Type Supply (Inlet) Pressure (mbar) Recommended Minimum Gas Pipe Size Natural 9-14” WC (2.2 kPA / 22.4 mbar - 3.5kPa / 34.9 mbar) 2” (51 mm) LP 11-14” WC (2.7 kPa / 27.36 mbar - 3.5 kPa / 34.9 mbar) 2” (51 mm) *Gas supply pressures are dependent on loc...
Global 91” (2311mm) 3/4” N.P.T. INLET w/Tee (19 mm) 120 VOLT 10 FT. LONG POWER CORD 3/4” N.P.T. (19 mm) UNION GAS DOOR SWING 80” (2032 mm) 18” (457 mm) 40” (1016 mm) 22” (585 mm) 7 1/2” (191 mm) 44 1/8” (1121 mm) 32 1/8” (816 mm) 7 1/2” (191 mm) 32 1/8” (816 mm) 51 3/8” (1305 mm) 63 3/8” (1610 mm) 5...
