Lightolier IS:26600 - Manual
Lightolier IS:26600 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – INSTRUCTION SHEET NO.; Recessed ProSpec; MOUNTING PROSPEC
- Page 3 – Instructions; FEED FROM ABOVE TRACK; FEEDING ALONG THE TRACK LENGTH; The floating splice box may
- Page 4 – FIELD CUTTING TRACK; CAUTION DO NOT OPEN THE GAP MORE; Recessed ProSpec
IS:26600
READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING TRACK
This fixture is intended for installation in accordance with the National Electrical Code and local or Federal code
specifications. To assure full compliance with codes and regulations, check with your local electrical inspector
before installation. To prevent electric shock, turn off electricity at fuse box before proceeding.
Save these instructions for maintenance reference
and refer to them when additions to or changes in the track configuration are made.
INSTRUCTION SHEET NO.
A0397
Page 1 of 4
F A L L R I V E R , M A S S A C H U S E T T S 0 2 7 2 0
M O N T R E A L , Q U E B E C , C A N A D A
ProSpec™ track lighting is designed to support and energize ProSpec™ Lytespots
®
which can be
attached anywhere along the track. It is a four conductor system, continuously grounded through-
out, to be supplied by two single 120V, 20 amp, 60Hz branch circuits. It is not intended for use with
a power cord or convenience receptacles. ProSpec™ is listed by Underwriters Laboratories, Inc. It
may only be used with electrical fittings identified for use with ProSpec™ track.
Installation Instructions for ProSpec
™
Track Lighting--
Recessed Feed Track and Plain Track Units.
IMPORTANT SAFETY INSTRUCTIONS
Read all Track, Connector, Feed-in Kits, and Accessory Instruction Sheets before
installing any ProSpec
™
Track item. When installing or using this track system, basic
safety precautions should be followed:
Read all instructions
before installing the track system.
•
Do not install in wet media (concrete, plaster, etc.).
•
This track system is intended for installation in accordance with the National
Electrical Code and Local or Federal Codes.
•
Do not install this track in wet or damp locations.
•
Do not install any part of this track system less than 5 feet above floor.
•
Do not install any fixture assembly closer than 6 inches from any curtain, or similar
combustible material.
•
To prevent electrical shock, turn off electricity at fuse box before installing the track
or adding to or changing the configuration of the track.
•
Instructions for grounding per instruction sheet of the feed-in kit used must be
followed. Failure to do so may result in a hazardous condition.
•
Use #12 ga. AWG solid wire only (not stranded wire) for supply to track.
•
Observe polarity, white supply lead (neutral) to contact marked “NEUT” on screw
terminal connectors.
•
Do not exceed 4 feet between mounting points.
•
Do not attempt to energize anything other than track lighting fixtures on the track.
To reduce the risk of fire and electrical shock, do not attempt to connect power tools,
extension cords, appliances and the like to the track.
SAVE THESE INSTRUCTIONS
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
IS:26600 INSTRUCTION SHEET NO. A0397 Page 2 of 4 Recessed ProSpec ™ Track Mounting Methods FIG. A FIG. B FIG. C FIG. D MOUNTING PROSPEC ™ TRACK There are three methods of mounting the track to a surface (Fig A, B & C). 1. Direct mounting (Fig A): • Mark centerline for track location. • Add mount...
IS:26600 INSTRUCTION SHEET NO. Instructions for Recessed ProSpec ™ Track Power Feed to Track DIRECT POWER FEED TO "FEED" TRACK Use solid 12 ga. copper wire when feeding the track. The feed track acceptstwo separate 120 V, 60 Hz branch circuits. Each circuit must not exceed the20 amp capacity...
FIELD CUTTING TRACK • Remove and save the Dead End Cover. • Cut the track using a metal cutting blade (preferably in a miter box to obtain a square cut) • Remove ALL burrs and sharp edges from the cut surface of the track being careful not to destroy the integrity of the track geometry. Thereshould ...
