Page 2 - SAFETY—DANGERS, WARNINGS AND CAUTIONS
2 READ AND FOLLOW ALL WARNINGS AND INSTRUCTIONS BEFORE ASSEMBLING AND USING THIS APPLIANCE. These assembly instructions contain important product dangers, warnings and cautions necessary for proper assembly and safe use of this appliance. Anyone using this grill and pellet smoker must follow all war...
Page 4 - HELPFUL HINTS
4 • At least three people are required for assembly.• Assemble this appliance outdoors on a flat, level and soft surface.• To help keep parts looking new, ONLY unpack parts as needed during the assembly process.• DO NOT use power tools for assembly.• DO NOT throw away any boxes until you’ve verified...
Page 5 - GRILL CABINET ASSEMBLY PARTS; HAC
5 GAS GRILL CABINET ASSEMBLY AMU AMU GVQ GVJ GVJ GWN GVR GVI GVS GVP Wheel Axle GVO Large Washer GVE #8-32 x 1/2" Truss Screw GVF 1/4"-20 x 1/2" Truss Screw GWO Axle Cotter Key GZS 1/4" Flat Washer GZT 1/4" Lock Washer GZW #8-32 x 1/2" Flat-Head Screw 1 TOOLS REQUIRED GVN (x2...
Page 6 - Do not completely tighten the
TOOLS AND HARDWARE REQUIRED u SECTION 1 (CONTINUED) 6 1.3 1.4 • Attach the left panel to the cabinet floor using the hardware indicated. Do not completely tighten the screws yet. • Attach the left panel (GVQ) to the cabinet floor using the hardware indicated. Do not completely tighten the screws yet...
Page 7 - Do
TOOLS AND HARDWARE REQUIRED u SECTION 1 (CONTINUED) 7 1.7 1.8 1.5 1.6 • Secure the right panel (GVR) to the cabinet floor using the hardware indicated at the locations shown. Do not completely tighten the screws yet. • Secure the right panel to the rear panel using the hardware indicated. Tighten al...
Page 8 - • Lock the casters by pressing down on the tabs.
TOOLS AND HARDWARE REQUIRED u SECTION 1 (CONTINUED) 8 GVK GVK GWO GWO 1.9 1.10 1.12 1.11 • Insert a cotter key (GWO) through each axle to secure the wheels in place. • Snap a hub cap (GVK) onto each wheel as shown. If necessary, use a rubber mallet to gently tap the caps in. • Lock the casters by pr...
Page 9 - With the casters still locked, flip the cabinet upright.; Secure the
TOOLS AND HARDWARE REQUIRED u SECTION 1 (CONTINUED) 9 • With the casters still locked, flip the cabinet upright. Secure the doorstop (GWL) to the floor using two (2) screws (GZW) shown. GZW GZW GWL GWL (x1) 1.13 GZW (x2) HAC #2
Page 10 - GRILL AND STORAGE BOX ASSEMBLY; PROPANE/STORAGE BOX ASSEMBLY PARTS
10 GVZ GrillGVV Chimney Stack GWB Hopper Lid GVL Temperature Knob GXT Warming Rack GXU Cooking Grate GXV Grill Lid Handle GXW Upper Burner Plates GVH Grease Bucket GZM Grease Bucket Liners GYV Power Cord AGO Left Cabinet Door AGZ Right Cabinet Door GVT Door Handle GXY Lower Burner Shield GVW Front S...
Page 11 - HAE
11 GRILL AND STORAGE BOX ASSEMBLY 2 #2 (Phillips) TOOLS REQUIRED GVX (X1) SECTION 2 BLISTER PACK HARDWARE (HAE) GVE #8-32 x 1/2" Truss Screw GVF 1/4"-20 x 1/2" Truss Screw GVG 1/4"-20 x .8" Truss Screw GWS M6 x 1 mm x 10 mm Shoulder Bolt GWM Hinge Pin Cotter Key GWA Hinge Pin GZS...
Page 12 - propane
12 TOOLS AND HARDWARE REQUIRED u SECTION 2 (CONTINUED) 2.1 • Attach the rear panel (GWJ) to the propane compartment base (GWF) using three (3) screws (GVE) . GVE GVE GVE GWF GWJ 2.2 2.3 2.4 • Attach the front panel (GVW) to the base using three (3) screws (GVE) . • Align the holes in the angled side...
Page 13 - • Secure the; • Gently set the
13 TOOLS AND HARDWARE REQUIRED u SECTION 2 (CONTINUED) • Secure the storage box (GWI) to the assembly using the hardware indicated. GVF GZT GZT GZT GZT GZS GZS GZS GZS GVF GVF GWI GVF 2.5 2.6 HAE GVF (x4) GZS (x4) GZT (x4) GVE (x2) GVE GVE GVX (x1) GVX • Gently set the grill/hopper assembly (GVZ) on...
Page 14 - Ensure the propane hose and igniter cables; GVZ
14 TOOLS AND HARDWARE REQUIRED u SECTION 2 (CONTINUED) 2.7 • While one adult holds the grill/hopper assembly upright, have two other adults, one on each side of the cabinet assembly, gently slide the cabinet into the grill/hopper assembly as shown. Ensure the propane hose and igniter cables are on t...
Page 15 - . Secure the grill to the cabinet with; into the holes
15 TOOLS AND HARDWARE REQUIRED u SECTION 2 (CONTINUED) 2.8 2.10 • Adjust the regulator hose so the holes in the bracket align with those in the cabinet. Secure the bracket to the cabinet with two (2) screws (GVE) . Secure the grill to the cabinet with hardware indicated. 2.9 • Secure the cabinet to ...
Page 16 - • Set the keyslots over the four screws indicated.; Tighten the upper two screws
16 TOOLS AND HARDWARE REQUIRED u SECTION 2 (CONTINUED) 2.11 2.12 HAE GVF (x2) GZS (x2) GZT (x2) • Set the keyslots over the four screws indicated. • Slide the propane compartment towards the wheels to help lock it in place. Secure with the hardware indicated. Tighten the upper two screws also. GZT G...
Page 17 - • Remove the small screw and washer from the
17 TOOLS AND HARDWARE REQUIRED u SECTION 2 (CONTINUED) 2.13 2.14 HAE GVF (x3) Screw Washer GZS (x3) GZT (x3) • Secure the front panel to the cabinet using the hardware indicated. • Remove the small screw and washer from the wing bolt (GYQ) . Insert the wing bolt as far as it will go. Once the wing b...
Page 18 - near each end of the box.; Tighten the two upper screws also.; GWS
18 TOOLS AND HARDWARE REQUIRED u SECTION 2 (CONTINUED) • With the casters still locked, set the assembly back on its wheels. Secure the storage box to the grill using two (2) shoulder bolts (GWS) near each end of the box. Tighten the two upper screws also. Tighten these two screws also. GWS GWS 2.15...
Page 20 - • Slide the tabs on the side of the; igniter box cover; into the slots in the storage box. Secure; It doesn’t matter the order.; GVE
20 TOOLS AND HARDWARE REQUIRED u SECTION 2 (CONTINUED) 2.20 • Slide the tabs on the side of the igniter box cover (GWC) into the slots in the storage box. Secure the igniter box cover to the storage box using one (1) screw (GVE) . • Thread the igniter cables up through the hole in the storage box. A...
Page 21 - storage box lid
21 TOOLS AND HARDWARE REQUIRED u SECTION 2 (CONTINUED) 2.22 2.24 2.23 • Secure a lower hinge (GWQ) to the storage box using three (3) screws (GVE) . • Secure the storage box handle (GXV) to the storage box using two (2) handle bezels (GVU) and the hardware indicated. • Secure an upper hinge (GWP) to...
Page 22 - hinge
22 TOOLS AND HARDWARE REQUIRED u SECTION 2 (CONTINUED) 2.26 2.28 2.25 2.27 • Insert a hinge pin (GWA) through the hinge as shown. GWA GWA • Insert one (1) cotter key (GWM) through the hinge ping to secure the lid to the storage box. You may want to open the lid when performing this step. GWM • Secur...
Page 23 - handle
23 TOOLS AND HARDWARE REQUIRED u SECTION 2 (CONTINUED) 2.30 2.32 2.31 • Insert a hinge pin (GWA) through the hinge as shown. Insert a cotter pin (GWM) through the hinge pin as shown to lock it in place. • Set the upper hinge down around the outside of the lower hinge and align the holes. 2.29 GWA GW...
Page 24 - • Attach the right door in a similar manner.; Top hinge pin
24 TOOLS AND HARDWARE REQUIRED u SECTION 2 (CONTINUED) 2.34 2.33 • Insert the bottom hinge pin of the left door into the hole in the bottom left corner of the cabinet. Push down the top hinge pin and push in the door to allow the pin to pop up into the hole in the top right corner of the cabinet. • ...
Page 25 - grease
25 TOOLS AND HARDWARE REQUIRED u SECTION 2 (CONTINUED) 2.36 • Secure the chimney stack (GVV) to the lid using four (4) screws (GVE) as shown. • Open the grill lid and secure a lid handle (GXV) to the lid using two (2) shoulder bolts (GWS) and two (2) handle bezels (GVU) as shown. 2.35 2.37 GXV GVU G...
Page 28 - Repeat the steps for the remaining three lower
28 TOOLS AND HARDWARE REQUIRED u SECTION 2 (CONTINUED) 2.44 2.43 • Now bring the lower burner shield forward and insert the tabs at the front end into the slots in the front wall of the chamber. • FInally, set the slots in the rear end of the lower burner shield over the two tabs in the v-slot in th...
Page 29 - temperature
29 TOOLS AND HARDWARE REQUIRED u SECTION 2 (CONTINUED) 2.46 2.45 2.47 • Place the two (2) cooking grates (GXU) and the warming rack (GXT) onto the grill as shown. • Set the burner plates (GXW) over the tabs on the front and back of the grill box. GXW GXW GXW GXW GXT GXU GXU • Connect the temperature...
Page 30 - • Tighten the; Ensure the handwheel on the propane tank is; Set the tank in the propane; Tighten until it; GYQ
30 TOOLS AND HARDWARE REQUIRED u SECTION 2 (CONTINUED) 2.49 2.48 • Tighten the bolt (GYQ) to secure the propane tank to the floor as shown. • Ensure the handwheel on the propane tank is completely shut off. Set the tank in the propane compartment. Remove the cap from the propane tank’s cylinder valv...
Page 31 - PROPERTY DAMAGE AND EVEN DEATH.; GZO
31 TOOLS AND HARDWARE REQUIRED u SECTION 2 (CONTINUED) 2.50 • The electric ignition requires 1 “AA” alkaline battery (included). 1. Remove the igniter button/cap from the igniter panel. 2. Insert the battery, negative end first. 3. Re-attach the igniter button. WARNING: READ THE USER’S GUIDE BEFORE ...
Page 32 - GRILL AND SMOKER PARTS VIEW
32 GVZ GrillGVV Chimney Stack GWB Hopper Lid GXT Upper Grill Grate GXU Lower Grill Grate GXV Grill Lid Handle GVL Temperature Control Knob GVH Grease Bucket GZM Grease Bucket Liner GXW Upper Burner Shields GYV Power Cord GXY Lower Burner Shields GRILL AND SMOKER PARTS VIEW GVL GVV GWB GVZ GVL GVL GX...
Page 33 - GRILL CABINET PARTS VIEW
33 GRILL CABINET PARTS VIEW GVT GVT AMU AMU GVQ GVJ GVJ GWN GVR GVI AGO AGZ GVS GVI Cabinet Floor GVS Rear Cabinet Panel GVQ Left Cabinet Panel GVR Right Cabinet Panel GWN Cabinet Cross Brace AGO Left Cabinet Door AGZ Right Cabinet Door GVJ CasterAMU WheelGVT Cabinet Door Handle
Page 34 - PROPANE COMPARTMENT PARTS VIEW; GZX
34 GWF GVW GWE GWJ GWG GWH GWC GWD GWI GVW Front Storage Panel GWF Storage Base GWI Storage Box GWE Right Storage Panel GWJ Rear Storage Base Panel GWD Ignitor Cover Panel GWC Ignitor Box Cover GWH Storage Box Lid GWG Storage Box Handle SPARE HARDWARE BAG (GZX) ID # Description GVE x5 #8-32 x 1/2...
Page 35 - NOTES
Page 38 - LIFETIME’S PROMISE TO YOU:; REGISTER YOUR PRODUCT ONLINE AT WWW.LIFETIME.COM
38 LIFETIME’S PROMISE TO YOU: We invite you to read our privacy policy at www.lifetime.com REGISTER today! At Lifetime ® , we are committed to providing innovative and quality products. While registering, you will have the opportunity to give us your feedback. Your input is valuable to us. • You can...
Page 39 - Australian customers.; THE MANUFACTURER RESERVES THE RIGHT TO MAKE SUBSTITUTIONS TO; FOR INTERNATIONAL WARRANTY CLAIMS:; LIMITED FACTORY WARRANTY
39 Lifetime Gas Grill and Pellet Smoker is warranted to the original purchaser to be free from defects in material or workmanship according to the following periods from the date of original retail purchase. Auger and fan—3 yearsElectronics—3 yearsAll other parts—5 years The word “defects” is defi n...
Page 40 - ENHANCE YOUR LIFETIME; Du lundi au vendredi de 7 h à 17 h, HR et le samedi de 9 h à 13 h, HR; Pour acheter des accessoires ou des autres produits Lifetime; AMÉLIORER L’ACHAT LIFETIME
40 www.lifetime.com Or call: 1-800-424-3865 7:00 am–5:00 pm (M–F) MST and 9:00 am–1:00 pm Saturday MST To purchase accessories or other Lifetime ® products, visit us at: www.lifetime.com O marcar al 1-800-424-3865 De lunes hasta viernes 7:00 h–17:00 h Horario Éstandar de la Montaña (MST) y sábados 9...
