Life fitness Fit-1 - Manual

Page 2 - PARTS LIST

PARTS LIST PART # 04-1325 04-1326 04-1327 04-1328 04-1330 04-1335 04-1329 04-1334 04-1331 04-1338 04-1336 04-1337 04-1332B 04-1339B 04-1333 04-1340 02-1294 01-2073 01-2008 02-1292 02-1296 02-1295 10-0056 10-0057 03-0340 02-1293 01-1784 04-1386 10-0204 06-0304 7 2 9 2 5 06-0382 11-0067 04-0622 06-036...

Page 4 - Tools Required for Assembly

4 67 3/8 X 4-1/4” (106m) BOLT 69 3/8 X 6-1/2” (164m) BOLT 72 3/8 X 3” (76m) BUTTON HEAD BOLT 57 1/2 X 3” SHOULDER BOLT 5 5 1” FLANGE SPACER 71 3/8 X 1” (25m) BUTTON HEAD BOLT 5 4 1/2” FLANGE SPACER 5 6 3/4” FLANGE SPACER BOLT LENGTH Tools Required for Assembly NOTE: BOLT LENGTH IS MEASURED FROM THE ...

Page 5 - FIGURE 1; LOOSELY

STEP 1: FIGURE 1 5 • LOOSELY assemble the REAR UPRIGHT (5) to the BASE (1) to the using four RH CAPS (78), two 3/8 X 3-1/2” BOLTS (63), four 3/8” SAE WASHERS (75), four 3/8” RH WASHERS (76) and two 3/8” LOW HEIGHT LOCK NUTS (73) as shown in FIGURE 1. 3/8 X 3-1/2” (90m) 63 7 5 7 6 7 3 7 8 1 5 0 1 1/2...

Page 6 - FIGURE 2

STEP 2: FIGURE 2 6 • LOOSELY assemble the LEFT and RIGHT BOOM SUPPORTS (3 & 4) to the REAR UPRIGHT (5) using four RH CAPS (78), two 3/8 X 3” BOLTS (65), four 3/8” SAE WASHERS (75), four 3/8” RH WASHERS (76) and two 3/8” LOW HEIGHT LOCK NUTS(73) as shown in FIGURE 2. 3/8 X 3-1/2” (90m) 63 7 5 7 6...

Page 7 - SECURELY

FIGURE 3 7 STEP 3: FIGURE 4 STEP 4: • SECURELY assemble one STORAGE PEG (25) to the LEFT BOOM SUPPORT (3) using one RH CAPS (78), one 3/8 X 1” BOLT (60), one 3/8” SAE WASHER (75) and one 3/8” RH WASHER (76) as shown in FIGURE 3. • LOOSELY assemble the UPRIGHT SUPPORT (6) to the BASE (1) and REAR UPR...

Page 9 - FIGURE 7

9 STEP 7: TIGHTEN! • Securely tighten all loose frame connections made to this point, then proceed to snap RH CAPS (78) over the RH WASHERS (76) on all tightened connections. TIGHTEN! FIGURE 7 0 1 1/2 1/2 1/2 1/2 1/2 1/2 2 3 4 5 6 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150

Page 10 - SECURE

STEP 9: FIGURE 9 1 0 STEP 8: FIGURE 8 5 1 1 8 7 7 6 7 8 7 3 7 5 3/8 X 4-1/4” (106m) 67 2 7 • Insert one 3-5/16” PIVOT SHAFT (47) into the PEDESTAL (7) as shown in FIGURE 8. • Assemble four 5 X 8” ROLLER PADS (39) and eight 2-3/8” OD PLASTIC WASHERS (32) to the PEDESTAL (7) using four 1- 1/4” SHAFT C...

Page 17 - EXTREME CARE

STEP 24: FIGURE 24 1 7 • Insert two GUIDE RODS (27) through the BOTTOM SHROUD BRACKET (20) and into the BASE (1) as shown on FIGURE 24. • Slide two 3/4 X 2” WEIGHT STACK CUSHIONS (30) down over the GUIDE RODS (27) as shown in FIGURE 24. • Using EXTREME CARE slide all twenty WEIGHT PLATES (31) down o...

Page 19 - groove of PULLEY before tightening BOLTS.)

1 9 FIGURE 27 STEP 27: 64 3/8 X 2-1/2” (67m) 8 5 0 3 8 FIGURE 28 STEP 28: 7 3 7 8 62 3/8 X 1-3/4” (43m) 2 1 7 6 7 5 • Slide the two 13/16” SHAFT COLLARS (50) to the top of the STACK BOOM (8) and SECURELY tighten the SHAFT COLLAR (50) set screws. • Route the LAT CABLE (44) through the REAR UPRIGHT (5...

Page 26 - PREVENTATIVE MAINTENANCE TIPS; Consult your physician before beginning any exercise program.; Action; CLEAN; WARRANTY INFORMATION

Clean: • Upholstery with mild soap and water.• Guide rods with a cotton cloth.• Hand grips with mild soap and water.• Frame damage can be repaired with touch-up paint can be purchased from your LifeFitness customer service representative at (800) 351-3737 Inspect: • Cables for wear or damage and pro...

Life fitness Fit-1 - Manual

Table of Contents:

Summary

Other Life fitness Models