Life fitness 841101 - Manual

Page 2 - BOLT LENGTH RULER:; Bolt Length Ruler; WELCOME TO THE WORLD OF; BOLT LENGTH; Consult a physician before beginning any exercise program.

IMPORTANT NOTES Please note: Tools Required for Assembly * Thank you for purchasing the Parabody 841101 WEIGHT STACK OPTION. Please read these instructions thoroughly and keep them for future reference. This product must be assembled ona flat, level surface to assure its proper function. * 3/4” wren...

Page 3 - PARTS LIST; FIGURE 1

3 PARTS LIST PART # 6 7 5 0 8 0 3 6 7 5 3 7 0 3 6 2 7 4 4 0 2 6 2 7 5 3 0 2 6 6 0 9 0 0 2 6 6 1 0 4 0 2 6 7 5 0 5 0 3 6 1 7 6 2 0 1 6 7 5 4 5 0 1 6 1 8 9 5 0 1 311 6 1 0 1 311 6 2 0 1 6 2 8 4 5 0 1 6 7 1 4 6 0 1 6 7 5 8 7 0 1 6 5 7 7 7 0 1 6 5 4 2 4 0 2 3 1 0 3 1 0 2 3 1 0 8 0 0 2 6 5 9 5 2 0 1 311 ...

Page 4 - FIGURE 2; POWER RACK

4 FIGURE 2 STEP 2: • SECURELY assemble the LOW ROW ATTACHMENT (5) and the UPRIGHT (1) to the POWER RACK using two 3/8 X 3-1/4” BOLTS (27), four 3/8” WASHERS (31), and two 3/8” LOCK NUTS (32). See FIGURE 2. 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 1 36 5 31 32 POWER RACK • Insert two 2” SQ ENDCAPS (36) ...

Page 5 - FIGURE 4; FIGURE 3

5 FIGURE 4 • Insert two WEIGHT PLATE BUSHINGS (42) into the “PARABODY” side of each of the twentyWEIGHT PLATES (43) as shown in FIGURE 4. STEP 4 43 42 FIGURE 3 STEP 3 • Slide one 2” SQ. COVER CAP (22) over the end of the WEIGHT STACK BASE (7) as shown in FIGURE 3. • SECURELY assemble the WEIGHT STAC...

Page 6 - FIGURE 5

6 • Insert four CAP PLUGS (21) into the bottom end & top end of the two GUIDE RODS (9) as shown in FIGURE 5. STEP 5: FIGURE 5 9 31 23 3/8 X 1-1/4” 13 43 10 21 7 19 14 21 • Insert two GUIDE RODS (9) into the WEIGHT STACK BASE (7) as shown on FIGURE 5. (NOTE: Lubricate GUIDE RODS (9) with silicon ...

Page 7 - FIGURE 6

7 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • SECURELY assemble two 3-1/2” PULLEYS (12) to the TOP BOOM (2) using two 3/8 X 2-3/4” BOLTS (25), four 3/8” FLANGE SPACERS (33), and two 3/8” LOCK NUTS (32). See FIGURE 6. (NOTE: BEFORE TIGHTENING, MAKE SURE CABLE (15) IS IN THE GROOVES OF THE PULLEYS.) STEP ...

Page 8 - FIGURE 8

8 STEP 8: FIGURE 8 • SECURELY assemble two 3-1/2” PULLEYS (12) to the TOP BOOM (2) using two 3/8 X 2-3/4” BOLTS (25), four 3/8” FLANGE SPACERS (33), and two 3/8” LOCK NUTS (32). See FIGURE 8. (NOTE: BEFORE TIGHTENING, MAKE SURE CABLE (15) IS IN THE GROOVES OF THE PULLEYS.) • Route threaded end of th...

Page 9 - FIGURE 9

9 STEP 9: FIGURE 9 • Swing the GUIDE RODS (9) under the TOP BOOM (2) as shown on FIGURE 9. • Assemble the TOP BOOM (2) over the GUIDE RODS (9) and SECURELY assemble the TOP BOOM (2) to the UPRIGHT (1) using two 1/2 X 3” BOLTS (28), two 1/2” WASHERS (29), and one 1/2” LOCK NUT (30). See FIGURE 9. • S...

Page 14 - THIS CONCLUDES THE ASSEMBLY OF THE 841101 WEIGHT STACK OPTION

14 STEP 17: FIGURE 17 • If upon completion of assembly, the HEAD PLATE (14) does not sit on top of the first WEIGHT PLATE (43), push the HEAD PLATE (14) down, insert the WEIGHT STACK PIN (39) and perform several repetitions at the press station. This will relax thecable system and prevent the HEAD P...

Life fitness 841101 - Manual

Table of Contents:

Summary

Other Life fitness Models