Life fitness 660 - Manual - manualsarea.com

Page 2 - IMPORTANT SAFETY INFORMATION; TABLE OF CONTENTS

THERE IS A RISK ASSUMED BY INDIVIDUALS WHO USE THIS TYPE OF EQUIPMENT. TO MINIMIZE RISK FOLLOW THESE RULES ! 1. Before using, read all the warnings and instructionson the use of this machine. Use only for intendedexercise. DO NOT modify the machine. 2. Obtain a medical exam before beginning anyexerc...

Page 3 - BOLT LENGTH RULER:; Bolt Length Ruler; BOLT LENGTH

IMPORTANT NOTES Please note: Tools Required for Assembly * Thank you for purchasing the ParaBody 660 Gym System. Please read these instructions thoroughly and keep them for future reference. 3 NOTE: BOLT LENGTH IS MEASURED FROM THE UNDERSIDE OF THE HEAD OF THE BOLT. BOLT LENGTH RULER: * This product...

Page 5 - PARTS LIST

5 PART # 6 7 3 2 6 0 87 0 4 1 9 0 86 7 2 6 9 0 26 7 3 2 7 0 86 7 3 2 4 0 27 0 4 2 0 0 86 7 2 5 9 0 26 7 2 3 8 0 86 7 3 1 6 0 26 7 3 3 5 0 26 7 3 2 2 0 26 7 3 3 4 0 26 7 3 2 3 0 86 7 3 2 5 0 86 7 3 1 5 0 86 7 2 6 7 0 27 0 4 2 1 0 86 7 3 7 8 0 86 7 3 1 3 0 86 7 3 1 2 0 86 7 2 3 2 0 86 7 2 5 5 0 26 7 3...

Page 6 - FIGURE 1; SECURELY

6 FIGURE 1 STEP 1 • SECURELY assemble the LOW ROW/CALF RAISE (2) to the PRESS BASE (18) using two 1/2 X 3" BOLTS (87), two 1/2" WASHERS (93), and one 1/2" LOCK NUT (94). • Insert two 1/2" FLANGE BEARINGS (78) into the SWIVEL PULLEY BRACKET (30) as in FIGURE 1. • Assemble the SWIVEL P...

Page 7 - FIGURE 2; LOOSELY

7 FIGURE 2 STEP 2 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 4 1 9 3 9 4 • LOOSELY assemble the REAR UPRIGHT (4) to the BASE (1) using two 1/2 X 3” BOLTS (87), two 1/2” WASHERS (93), and two 1/2” LOCK NUTS (94) as shown in FIGURE 2. 87 1/2 X 3”

Page 8 - FIGURE 3

8 FIGURE 3 STEP 3 • SECURELY assemble one 4-1/2” PULLEY (43) to the upper flat on the BASE (1) using one 3/8 X 2-1/4” BOLT (86), two 3/8” WASHERS (91), one 2-7/8” L-BRACKET (44), one 3/8” HEX NUT (108), one SWIVEL SNAP (68) and one 3/8” LOCK NUT (92). See FIGURE 3. 86 3/8 X 2-1/4” 9 1 108 HEX NUT 1 ...

Page 9 - FIGURE 4

9 FIGURE 4 STEP 4 • SECURELY assemble three 4-1/2” PULLEYS (43) to the flats on the BASE (1) using three 3/8 X 2” BOLTS (84), six 3/8” WASHERS (91), two 2-7/8” L-BRACKETS (44), and three 3/8” LOCK NUTS (92). See FIGURE 4. 84 3/8 X 2” 9 2 9 1 4 3 9 2 1 4 4 9 1 4 3 91 86 3/8 X 2” 0 1 2 3 4 5 6 1/2 1/2...

Page 10 - FIGURE 5

1 0 FIGURE 5 STEP 5 • LOOSELY assemble the FRONT (25) & MIDDLE UPRIGHTS (8) to the BASE (1) using four 1/2 X 4” BOLTS (88) and four 1/2” LOCK NUTS (94) as shown in FIGURE 5. 2 5 1 1/2 X 4” 88 9 4 8

Page 11 - FIGURE 6

11 FIGURE 6 STEP 5 • LOOSELY assemble the PRESS BASE (18) to the BASE (1) using two 1/2 X 4” BOLTS (88), two 1/2” WASHERS (93), and two 1/2” LOCK NUTS (94). See FIGURE 6. 88 1/2 X 4” 1 8 1 9 4 9 3 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2

Page 12 - FIGURE 8; FIGURE 7

1 2 FIGURE 8 STEP 8 • LOOSELY assemble one 4-1/2” PULLEY (43) to the TOP BOOM (17) using one 3/8 X 2-3/4” BOLT (85), two 3/8” FLANGE SPACERS (49), and one 3/8” LOCK NUT (92). See FIGURE 8. 85 3/8 X 2-3/4” 1 7 4 9 9 2 4 9 4 3 FIGURE 7 STEP 7 • LOOSELY assemble the PRESS BASE (18) to the REAR (4) &...

Page 13 - FIGURE 9

1 3 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 FIGURE 10 STEP 10 • Position two 3/8 X 1/2” SPACERS (109) inside the rear bracket of the TOP BOOM and slide one 3/8” THREAD SHAFT (106) through the bracket. See FIGURE 10. • SECURELY assemble two 2” PULLEYS (69) to the rear bracket on the TOP BOOM using the ...

Page 15 - EXTREME CARE

1 5 FIGURE 13 STEP 13 • Insert two GUIDE RODS (36) into the BASE (1) as shown on FIGURE 13. (NOTE: Lubricate GUIDE RODS (36) with silicon or teflon spray available at most hardware stores.) • Slide two WEIGHT STACK SPACERS (34), two 3/4” WASHERS (71), and two WEIGHT STACK CUSHIONS (70) - IN THAT ORD...

Page 23 - strips so they will slide by each other.)

2 3 FIGURE 22 STEP 22 • CAREFULLY slide the PRESS ADJUSTMENT TUBE (22) into the RECEIVING TUBE (13). (NOTE: Make sure the spring pin barrel on the RECEIVING TUBE (13) is on the same side as the holes in the PRESS ADJUSTMENT TUBE (22).) • Attach four PARAGLIDE STRIPS (62) INSIDE the end of the RECEIV...

Page 24 - SECURE

2 4 FIGURE 23 STEP 23 • Insert two 3/4” FLANGE BEARINGS (76) into the PRESS ARM (27) as shown in FIGURE 23. • Hold the PRESS ARM (27) between the REAR (4) and MIDDLE UPRIGHTS (8) and slide the 3/4 DIA X 11” SHAFT (107) throught the MIDDLE UPRIGHT (8), PRESS ARM (27), and through the collar on the RE...

Page 25 - SPRING PIN ASSEMBLY TO FULLY ENGAGE

2 5 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 STEP 23 • SECURELY assemble the SPRING PIN ASSEMBLY of the PUSH/PULL CABLE to the SPRING PIN BARREL on the RECEIV- ING TUBE (13). (!!! IMPORTANT !!! TIGHTEN THE NUT OF THE SPRING PIN ASSEMBLY SECURELY) • Swing the PRESS ARM (27) up until the SPRING PIN of th...

Page 26 - NOTE: DO NOT TIGHTEN THE FRONT UPRIGHT TO THE TOP BOOM AT THIS TIME.

2 6 STEP 26 • SECURELY assemble one 3/8” X 1” BUTTON HEAD CAP SCREW (96) and one 3/8” LOCK NUT (92) to the last hole on the BACK PAD ADJUST (16). See FIGURE 27. FIGURE 27 • SECURELY insert one 2” SQ. END CAP (46) to the open end of the BACK PAD ADJUST (16). See FIGURE 27. • SECURELY tighten all loos...

Page 32 - HEX NUT

FIGURE 34 STEP 34 • Assemble two 3/8” HEX NUTS (108), two SWIVEL SNAP (68), and two 3/8” LOCK NUTS (92) to the 3/8” THREADED SHAFT (106) as shown in FIGURE 34. BASE 3 2 109 106 HEX NUT 68 92 • Position two 3/8 X 1/2” SPACERS (109) inside the bracket on the BASE and slide one 3/8” THREADED SHAFT (106...

Page 38 - should be at approximately a 45°

3 8 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 FIGURE 41 STEP 40 • Assemble one 3-1/2” PULLEY (42) around the PEC DEC CABLE (98) and to the PULLEY BRACKET (29) using one 3/8 X 2” BOLT (84), two 3/8” WASHERS (91) and one 3/8” LOCKNUT (92) as shown in FIGURE 40. FIGURE 40 STEP 41 • Slide the ends of the PE...

Page 50 - LIMITED WARRANTY

5 0 NOTES: LIMITED WARRANTY ParaBody extends the following LIMITED WARRANTY to the original owner of the ParaBody products. The Warranty terms apply to IN HOME USE ONLY. 1. LIMITED WARRANTY ON FRAME AND WELDS. If the frame of the ParaBody product or a weld should crack or break, it will be repaired ...

Life fitness 660 - Manual

Table of Contents:

Summary

Other Life fitness Models