Page 2 - WASHING MACHINE; SERVICE MANUAL; CAUTION
WASHING MACHINE SERVICE MANUAL MODELS : WF-T10(~3)0(~2,6)1(~5)TP(H,E,F)(S,3) WF-T802/T852(A)/T853AWF-T(F/C)1091~3, 1191~3T(C/H/P)WF-T(F/C)1022, 1122, 1001T(C/H/P)WF-T1268TH, 2409KTb, 2602kTaWF-T1491TP, T11292TP, T1292TP, T1291TPWF-T1081TP, T1592TP, T1593TPWF-T1241TP, T1133THWF-G15KTB, G13KTC, B15KTB...
Page 3 - IMPORTANT SAFETY NOTICE !; CONTENTS; Operating Instructions
2 SAFETY PRECAUTION! ■ DISASSEMBLE POWER CORD BEFORE SERVING ■ RECONNECT ALL GROUNDING DEVICES IMPORTANT SAFETY NOTICE ! This service information is intended for individuals possessing adequate backgrounds of electrical, electronic and mechanical experience.Any attempt to repair this appliance may r...
Page 5 - INSTALLATION INSTRUCTIONS; How to use the adjusting plates; Installation area; Install the washer on flat and firm; when the washing machine is installed on a carpeted floor.; Checking level; Open the lid, and check if the washer is
2. INSTALLATION INSTRUCTIONS 2-1. HOW TO ADJUST LEVEL 4 How to use the adjusting plates · Use the adjusting plates to level the washer when theadjustable legs cannot cover the gap. 1 2 Adjustable leg Turn the adjustable legs to set the washer horizontal (2 EA). Installation area · Install the washer...
Page 6 - Horizontal setting; Lift up the front of the washer and; Confirming level; Place the washer to original position
5 More than 10cm More than 2cm More than 2cm 3 5 4 Horizontal setting · Lift up the front of the washer and adjust level by turning the adjustable legs clockwise or using the adjustingplate. Confirming level Distance between drain hose and the wall Checking slope · If installation surface is tilted,...
Page 7 - to hot water tab.; Normal Type
2-2. CONNECTING WATER SUPPLY HOSE 6 Before connecting Water Supply Hose to water tap, check your hose type and choose correct instruction. Water Supply Hose may vary according to the country. Make sure connect blue inlet hose to cold water tab, and orange inlet hose to hot water tab. Connecting Wate...
Page 8 - Note
7 Rubber packing Screw Fixed sticker Rubber packing Guide plate Connector Connector Fixed sticker MiddleConnector MiddleConnector Water Supply Hose Pressing rod Pressing handle Connector Middleconnector Fixed Stiicker Pressing Handle Pressing Rod Water Supply Hose Separate Middle connector from Wate...
Page 9 - Screw Type; Connecting Water Supply Hose to the machine
8 Attach the water supply hose to the tap. Push the water supply hose up so that therubber packing within the hose can adherecompletely to the tap. Connect the water supply hose to the tap. Connect the water supply hose to the tap andthen tighten it by screwing it to the right. Check water leakage. ...
Page 10 - NOTE; For pump model
9 2-3. CONNECT THE DRAIN HOSE CAUTION Hose Guide 0.9~1.2m Drain Hose Within 50mm · Connect the drain hose to the outlet of the drain pumplocated at the rear of thewashing machine. · Attach the clip to the drain hose. And then push it towardthe body of the washing machine as indicated by thearrow. · ...
Page 11 - OPERATING INSTRUCTIONS
3. OPERATING INSTRUCTIONS 3-1. IDENTIFICATION OF PARTS 10 SOFTENER DISPENSER • Softener will automatically flow into the tub. BLEACH INLET DETERGENT DISPENSER FUNCTIONSELECTORS PULSATOR ANTI RAT BASE ADJUSTABLE LEG SPINDLE DRAIN HOSE For non Pump Model • Keep downward while the washing machine iswor...
Page 12 - Fire Hazard; Never place items in the washer that are; WARNING
11 3-2. BEFORE STARTING TO WASH • Check all pockets to make sure that they are empty . Things such as nails, hairclips, matches, pens, coins, and keys can damage both your washer and your clothes. • Mend any torn garments or loose buttons . Tears or holes may become larger during washing. • Remove b...
Page 13 - Using Detergent; Detergent; Using Water; Amount of Water Level; Attention
12 • The temperature of the water impacts the effectiveness of all laundry additives and therefore, the cleaning results. We recommend temperatures of: - HOT 49~60°C…(120-140˚F) White items, diapers, underclothing and heavily soiled, colorfast items. - WARM 29~40°C…(85-105˚F) Most items - COLD* 18~2...
Page 14 - Attentión; How much detergent; • Check clothing care label for special instructions and separate; Using Liquid Bleach
13 Open the detergent dispenser and deposit the appropriate amount of detergent. Some detergents MUST be fully dissolved beforeadding to your machine to get the best wash results. Check the instructions on the detergent packet.If you use powdered detergent it is essential that the required amountbe ...
Page 15 - Using Fabric Softener; If you wish to use fabric softener we recommend; Available Fabric Softener Type
14 Using Fabric Softener If you wish to use fabric softener we recommend Scrud(Waxy Build up) Scrud is the name given to the waxy build-up that can occur within any washer when the fabric softener comes into contact withdetergent. This build-up is not brought about by a fault in the machine. If scru...
Page 16 - granular detergent and water.; For successful stain removal:; Stain Removal; STAIN; Special Guide for Stain Removal
15 • Remove stains promptly.• Determine the kind of stain, then follow the recommended treatment in the stain removal chart below. • To pretreat stains, use a prewash product, liquid detergent, or a paste made from granular detergent and water. • Use cold water on unknown stains because hot water ca...
Page 17 - LEVEL
16 3-3. FUNCTION OF EACH BUTTON ▶ Changing various functions is possible only in PAUSE state. Selection button does not work when the washer is in operation (Except for water level, water temp, water power button). S TRONG N ORMAL G ENTLE WATER LEVEL DELAY START WASH POWER EX- LARGE L ARGE M EDIUM S...
Page 18 - WASH; SPIN; GRAM; Abnormal water supply :; Use it to select washing; For manual wash, rinse
17 START PAUSE WASH RINSE SPIN PRO - GRAM AUTO OFF HOME DRY WOOL JEAN FUZZY BLANKET ECONOMY M M T SOAK WASH SHOWER RINCE (SPRAY) (NORMAL) (FAVOURITE) (DELICATE) (SPEEDY) SPIN INLET Er. DRAIN Er. DOOR Er. SPIN Er. 3 3 ■ In case of abnormal operation, the following indications are displayed. Abnormal ...
Page 21 - Soak; • Order of Soak-Wash timing
20 3-5. OTHERS FUNCTIONS 1) Soak Wash Use this mode for washing excessively dirty laundry by soaking in water for some time to remove proteins andfats. ‘ SOAK ’ mode can be used with all washing programs simultaneously except for WOOL and HOME DRY program. Note AUTO OFF The SOAK will not work in WOO...
Page 22 - DELAY START
21 2) Delay Start (Reservation) Wash 5 Delay start (Reservation) Wash is used to delay the finishing time of the operation. The hours to bedelayed can be set by the user accordingly. The time on the display is the finishing time , not the start time. 3 AUTO OFF • Finishing time can be delayed from 3...
Page 23 - RINSE
22 3) Option Washing Press the AUTO OFF (Power) button to turn power on. Press the WASH button to select the desired timing. Add the laundry into the washing tub. Press the START/PAUSE button. Press the WATER LEVEL button, to control the water level according to the amount of laundry. If you do not ...
Page 24 - When a Wash, Wash/Rinse or Rinse only option; is selected, after the wash is completed the water will not; If you do not specify the water level; , then Medium will be automatically selected.
23 3) Option Washing 2 Press the RINSE button to select the desired times ofrinse. Press the SPIN button to select the desired times of rinse. Press the AUTO OFF (Power) button to turn power on. Add the laundry into the washing tub. Press the S TART/PAUSE button. Add the detergent and close the lid....
Page 25 - ) Child Lock Function; Mute Option
24 4) Child Lock Function After all washing conditions are set according to the manual. Press the AUTO OFF (Power) button. Press the START/PAUSE button to start washing. During the wash program, all the buttons are locked untilwashing is completed or it is child- lockfunction is deactivated manually...
Page 26 - When there is a fear of freezing
25 Wash Inner-tub Leave the lid open after washing to allow moisture to evaporate. If you want to cleanthe inner-tub use a clean soft cloth dampened with liquid detergent, then rinse. (Donot use harsh or gritty cleaners.) Inlet Hoses Hoses connecting washer to faucet should be replaced every 5 years...
Page 27 - SERVICE INFORMATION
26 4. SERVICE INFORMATION 4-1. SCHEMETIC DIAGRAM 1) WF-T10(~3)0(~2,6)1(~5)TP(H,E,F)(S,3) / WF-T802/T852(A)
Page 33 - ) BRAKE LEVER ADJUSTMENT
32 4-4. ADJUSTMENT 1) BRAKE LEVER ADJUSTMENT Motor Pulley Clutch Pulley 2 2 1 2.0~3.5mm P.V Link Brake lever Motor Pulley Clutch lever Brake lever Lock net Adjustment screw Clutch lever Brake lever bar Keep the clearance 1.9 0.1mm between the tip of the adjustment screw and brake lever. • Shown as i...
Page 36 - ) Replacement of Damper asm; Separate top cover from washing machine.; Location; FRONT
35 4) Disassembly of Back Cover, Drain Pump, Clutch(Transmission) & Motor Remove back cover fixing screws thendisassemble the back cover. Disconnect the leads and the drain hose-p from thedrain pump. Remove the pump fixing screws then disassemblethe drain pump. Fall down the washer for clutch &a...
Page 37 - ) METHOD TO USE QC TEST MODE; Normal condition
36 4-6. TEST RUNNING WITHOUT WATER 1) METHOD TO USE QC TEST MODE Check method No. Check points Start/Pause Errorr Remedy KEY PUSH Press Load Display 1 LED Begining point Buzz once • LED on all - • Check pressure and • No.200 displayed S/W assembly. Pressure Sensor LEVEL • No.264~270 is • Check conne...
Page 38 - -7. TROUBLE SHOOTING AGAINST COMMON WASHING PROBLEMS; WASH PROBLEM; Blue Stains
37 4-7. TROUBLE SHOOTING AGAINST COMMON WASHING PROBLEMS Many washing problems involve poor soil & stain removal, residues of lint and scum,and fabric damage. For satisfactory washing results, follow these instructions. WASH PROBLEM Possible Causes Problems Solutions & Preventive Measures • ...
Page 39 - -8. TROUBLE SHOOTING METHODS ACCORDING TO ERROR MESSAGE; Error
38 4-8. TROUBLE SHOOTING METHODS ACCORDING TO ERROR MESSAGE ▶ For more detailed information for trouble shooting refer to page 38 to 49. Error Determination Expected cause Remedy INLET Er lamp blinks. Water supply doesn't reach set level within 60 minutes. DRAIN Er lamp blinks. When drain is not fin...
Page 41 - -9. HOW TO DIAGNOSE AND REPAIR BY SYMPTOM; Result of Check; Household Power supply; ∞ Ω and
40 4-9. HOW TO DIAGNOSE AND REPAIR BY SYMPTOM 1) Washer is not energized. Where, what & how to check? Result of Check Possible Cause How to repair & settle Household Power supply 1. Check whether connection between the plug and the electrical is poor 2. Measure voltage of the electrical. Wir...
Page 42 - ) Defects on displaying function; Main voltage; ) Reset During operation; Mains Voltage; Measure voltage of the outlet that the
41 2) Defects on displaying function Where, what & how to check? Result of Check Possible Cause How to repair & settle Main voltage 1. Measure mains voltage at the wall outlet 2. Meaure voltage at the extended outlet that the washer is plugged in if the extended outlet is used and voltage at...
Page 43 - Controller; ) Reset during operation
42 4) Water doesn’t come into the wash tub. Where, what & how to check? Result of Check Possible Cause How to repair & settle Inlet Valve 1. If water doesn’t come though the inlet valve works(electric sound occurs) 1) Check whether water mains is cut. 2) Check whether tabs are turned on. 3) ...
Page 44 - Wrong Installation/Leakage; Defect of controller is highly possible
43 4) Water doesn’t come into the wash bowl. 5) Water fills continuously or intermittently. Where, what & how to check? Result of Check Possible Cause How to repair & settle Wrong Installation/Leakage 1. Check whether the drain hose is laying down on the floor. (For pump model) 2. Check wher...
Page 46 - Drain Pump
45 6) Pulsator doesn’t rotate normally. Where, what & how to check? Result of Check Possible Cause How to repair & settle 4. Pulsator weakly rotates. 1) Check voltage at the power outlet where the washer is plugged into. 2) Check capacitance of the capacitor. L e s s t h a n 8 5 %of rating. ...
Page 48 - ) Water drains though it is not the time of drain.; PV Case; ) Drain error happens while water drains normally.
47 8) Water drains though it is not the time of drain. Where, what & how to check? Result of Check Possible Cause How to repair & settle Drain Motor(for Non-Pump Model only) 1. Check whether the drain motor is normally returned after turning power off.(It is considered normal if the lever of...
Page 49 - Motor
48 10) Spin extraction is not proceeded. Where, what & how to check? Result of Check Possible Cause How to repair & settle Motor 1. In the case that the wash motor does not spin during spin extraction; 1) Check there is motor working sound,or 2) If there is no motor-working sound; ① Check fr...
Page 50 - 1) Spining is going on even though the lid is open.; Tool low voltage
49 11) Spining is going on even though the lid is open. Where, what & how to check? Result of Check Possible Cause How to repair & settle Safety Switch 1. C h e c k r e s i s t a n c e b e t w e e n b o t h terminals of the safety switch withthe lid open. Ball Pressure Sensor 1. Is placed th...
Page 51 - Safety Switch; noise during spin and accumulately service experiance.
50 13) Vibration, Noise or Unbalance Error happens during spin. Where, what & how to check? Result of Check Possible Cause How to repair & settle Using conditions such as installation etc. 1. Check whether the washer is leveled. (Check clearance with out tub and out case the left gap is thes...
Page 52 - turning on the power switch.; Check whether power is
51 14) Power is automatically turned off during operation or immediately turning on the power switch. Where, what & how to check? Result of Check Possible Cause How to repair & settle Main voltage 1. It is mostly caused by noise frommains or transfomerient power cut. Auto Off switch orContro...
Page 54 - -1. THE EXPLODED VIEW OF TOP COVER ASSEMBLY
53 5-1. THE EXPLODED VIEW OF TOP COVER ASSEMBLY A210 A011 A330 A160 A201 A202 A220 A230 A170 A100 A 120 A240 A060 A110 A026 A020 A030 A200 A050 A040 A053 A024 A273 A274 HOT(ORANGE) COLD(BLUE) A271 A272 A275 A276 A277 HOT(ORANGE) COLD(BLUE) A270 HOT(ORANGE) COLD(BLUE) A180 A190 A151 A192 A191 A152
Page 55 - -2. THE EXPLODED VIEW OF OUT CASE ASSEMBLY; For Pump
54 5-2. THE EXPLODED VIEW OF OUT CASE ASSEMBLY F020 F080 F070 F021 F027 F090 F100 F001 F081 F084 F082 F050 F000 F010 : Non-Service Part For Non-Pump For Pump
Page 56 - or
55 5-3. THE EXPLODED VIEW OF TUB ASSEMBLY K000 K090 K010 K022 K024 K023 K020 K101 K102 K170 K180 K064 K130 K280 K190 K120 K011 K012 K027 K021 K025 K028 K063 K201 K200 K210 K220 K250 K230 K040 K050 K061 K030 K110 K060 K062 K270 BLUE NATURAL K150 K140 K160 or For Non-Pump For Non-Pump For Non-Pump For...
