LG WD-10124RD - Manual

3. PARTS IDENTIFICATION 6 ACCESSORIES Power plug Control panel Door Lower cover Adjustable feet (For detergent and fabric softener) Drawer Drum Drain hose Lower cover cap Drain pump filter Drain plug If the supply cord is damaged, it must be replaced by the manufacturer or its service agents or a si...

Before servicing ask troubles of customersCheck the adjustment(power supply is 220-240V~, remove the transit bolts....)Check the troubles referring to the trouble shooting.Decide service steps referring to disassembly instructions.And then, service and repair.After servicing, operate the appliance w...

TEST OPERATION 9 Power Start / Pause Power Connect the power plug to the outlet. In case of Coloreds program. Connect the inlet hose. Preparation for Press the POWER button. Press the Start/Pause washing. button. Press the Temp. button Check if the drum rotates Check if water is supplied and the pre...

10 5. OPERATION Start/Pause button • Use the button to start or pause wash cycle.•The power turns off automatically in 4 minutes after the pause button is pressed.• Press the button to change the program. Wash program selector • 7 programs can be selected depending on the type of the laundry.• By tu...

11 Dry selector • Dry programs can be selected by pressing the [Dry] button.• By pressing the button, [Auto Big Time Add Small ] can be selected. Water temperature selector • Press the button to select water temperature.• The water temperature is selected [60°C 95°C Cold 30°C 40°C] during cotton pro...

14 7-5.ERROR DISPLAY. If you press the Start/Pause button in error condition, any error except ‘ ’ will disappear and the machine will change into pause status. In case of if the error is not resolved within 20 sec., and in case of other errors, if the error is not resolved within 4 min., power will...

16 8-1.DIAGNOSIS AND ANSWER FOR ABNORMAL OPERATION 8. ERROR DIAGNOSIS AND CHECK LIST SYMPTOM GUIDE FOR SERVICE CALL NO POWER Water inlet trouble YES YES YES NO NO YES NO NO No Inlet Is the power plug connected firmly to 220-240V~ outlet? Power failure? or Breaker opened? Visit to check Is " "...

17 SYMPTOM • Door does not open• Error displayed on the program • DRAIN TROUBLE GUIDE FOR SERVICE CALL NO YES NO YES Started with door opened? NO YES Is the debris filter clogged with foreign material such as pin, coin and etc.? Is the drain hose frozen with water, kinked or crushed? Visit to check ...

18 SYMPTOM GUIDE FOR SERVICE CALL Suds overflow from the appliance. (In this condition, wash and spin do not operate normally) No effect of softener YES YES YES YES YES Is low-sudsing detergent for the drum washing machine used? Is the proper amount of detergent used as recommended? Recommend to red...

19 8-2.FAULT DIAGNOSIS AND TROUBLE SHOOTING 1. Be careful of electric shock or disconnecting the parts while trouble shooting. 2. First of all, check the connection of each part terminal with wiring diagram. 3. If you replace the MAIN PWB ASSEMBLY, Put in the connectors correctly. NO NO YES YES YES ...

20 NO YES NO NO YES NO YES YES NO NO YES YES YES NO NO NO YES Wiring diagram Option Option MAX Is water supply shut-off? Is the tap opened? When you press both Rinse button and Spin buttonsimultaneously, is the water level frequency below240? Is the inlet valve filter clogged with impurity? Is resis...

21 YES YES NO NO NO NO YES YES YES YES Wiring diagram Option MAX MAX max A B N O R M A L S O U N D S O F T E N E R D O E S N O T F L O W I N Fix the bolt tightly. Replace the STATORASSEMBLY or ROTORASSEMBLY. Refer to NO WATER SUPPLY Check the wiring on the dispenser. Put it in the correctcompartment...

22 Wash Rinse NO YES YES YES YES NO NO NO NO YES YES NO PWB ASSY(Main) AC 220V-240V (1) (2) Replace the S.PRESSURE SWITCH ASSEMBLY Replace the MAIN PWBASSEMBLY Repair the DRAIN HOSE ASSEMBLY. Remove foreign material. Reconnect or repair theconnector Repair the DRAIN PUMP ASSEMBLY. Repair the MAIN PW...

23 Push the THERMISTORtightly to the rubber. When checking THERMISTOR on the tub is the THERMISTOR loosened above 2mm from the rubber? HEATING CONTINUOUSLY ABOVE THE SETTING WATER TEMPERATURE

24 Rinse Spin Wash Rinse NO YES YES YES NO YES YES NO NO NO YES (1) (1) (2) Door Lock S P I N T R O U B L E D O O R D O E S N O T O P E N Check the S.PRESSURE SWITCHASSEMBLY or HOSE (Pressure). If the problem is on theS.PRESSURE SWITCHASSEMBLY or the HOSE,replace the S.PRESSURESWITCH ASSEMBLY or the...

Disassemble the cabinet cover andcondensing bellows.Is there any foreign object in condensingbellows. Clean the bellows [dHE] ERROR DISPLAY CHECK FOR DRY HEATER TROUBLE CHECK FOR DRY FAN MOTOR TROUBLE NO YES Replace the thermistor.(6322FR2046B) YES NO Disassemble the dry fan assy and dry ductupper, ...

9. DISASSEMBLY INSTRUCTIONS ƒR Disassemble and repair the parts after pulling out power cord from the outlet. ¤ Unscrew the screws on the top plate. ¤Ł The plate assembly(Top) is pulled back andthen upward to arrow direction. ¤Ø The cover(Inner) is disassembled. ¤ The PWB assembly(Display) connector...

30 ¤ The back cover is removed. ¤Ł Two screws are unscrewed. ¤Ø Disconnect connector from the wiring. ¤Œ Pull the PWB assembly (Main) to arrow direction. ¤ The plate assembly(Top)and the cover(lnner)are disassembled. ¤Ł Pull the drawer to arrow direction. ¤Ø Two screws are unscrewed. ¤ The hose clam...

31 ¤ Disconnect the wiring connector. ¤Ł Remove the valve by two screws of the valve holder. ƒT When reconnecting the connector 2 1 3 4 INLET VALVE VALVE ¥L (DRY) YL/BK - BK VALVE ¥M (PRE-WASH) GY/WH - BK VALVE ¥N (NORMAL-WASH) WH/BK - BK VALVE ®È (NORMAL-WASH) BL/RD - BK VALVE ¥O (HOT) BL/RD - BK ¤...

32 ¤ Open the door completely. ¤Ł Remove the two screws from the hinge. ¡ When removing the Door Assembly, it is necessary to hold the Bracket that is inner ofthe Cabinet Cover. ¤ Rotate the Cap(Remaining Hose) to arrow direction. ¤Ł Pull it out from hose. ¡ First, prepare a bucket to put in the rem...

33 ¤ The cabinet gasket clamp is released. ¤Ł Two screws are unscrewed from the cabinetcover. ¤ One screw is unscrewed from the lower cover. ¤Ł The lower cover is disassembled by pullingout. ¤Ø Three screws are unscrewed from the cabinet. ¤ The control panel is removed. ¤Ł Screw is unscrewed from th...

35 ¤ Remove the back cover. ¤Ł After loosening the bolt, Rotor, pull out the rotor. ¤ Remove the 6 bolt from the stator. ¤Ł Disconnect the 2 connectors. ¤ Remove the bolts at the Tub. ¤Ł The Hinge(Damper) at the base is pulled offpressing on the snaps at the sharp end. ¤Ø The hinge at the base is pu...

¤ Remove pump outlet hose. ¤Ł Remove tub pump bellows. ¤Ø Remove cap(Remaining Hose). ¤Œ Disconnect the wiring. ¤º Three screws are unscrewed from the cabinet. ¤ Remove the pump to arrow direction. ¤ Loosen the nut. ¤Ł Remove washing heater by pulling out. When assembling the washing heater, insertt...

¤ The cabinet cover clamp is removed and thegasket is released. ¤Ł Two screws are unscrewed. ¤Ø The door lock S/W is disconnected form thewiring connector and the strap. ¤ Remove washing heater. ¤Ł Remove the foreign object(wire,coin,etc) byinserting long bar in the hole. SWITCH ASSY, DOOR LOCK WHEN...

¤ Remove 5 screws and dry fan assembly. ¤Ł Remove 6 screws and dry duct upper. ¤ Remove 1 screw and dry heater. ¤Ł Remove thermostat. ¤ Remove 2 screws from cabinet. ¤ Remove clamp and condensing duct. DRY DUCT CONDENSING DUCT Dry fanAssembly Dry Duct Upper Dry Heater Thermostat Condensing Duct Cond...

10-1.THE PART LIST OF CABINET ASSEMBLY 10. EXPLODED VIEW AND PART LIST A110 A101 A100 A410 A201 A220 A210 A303 A310 A133 A440 A130 A131 A141 A103 A104 A102 A150 A120 A200 A300 A430 A485 A450 :Non-service part :Service part A275 A276 A277 HOT(ORANGE) COLD(BLUE) 39

10-3 THE EXPLODED VIEW OF DRUM & TUB ASSEMBLY K350 K143 K310 K105 K410 K610 K611 F140 K320 K540 K520 K531 K340 K344 K341 K343 K530 K100 K510 K511 K513 K131 K130 K141 K140 K110 K142 K411 K420 K123 K120 K360 K211 :Non-service part :Service part 41

10-4 THE EXPLODED VIEW OF DRYER M100 M110 M210 M101 M220 M230 M120 M121 M310 M312 M311 :Non-service part :Service part 42