LG PCM-MS2 - Manual - manualsarea.com

Page 2 - Contents; WARNING

- 2 - - Assembly drawing - Securing the bottom wall plate - Fine tune tilt adjustments - Securing the top plate - Flat panel list - Securing the flat panel to the wall mount - Parts list - Lateral shift adjustment - Checking thread depth - Finding the center of the flat panel - Positioning the mount...

Page 3 - Description; Assembly drawing; Dimensions are in Inches and (; mm

- 3 - 16.000 (406.4) 28.000 (171.2) 16.000 (406.4) 16.000 (406.4) 16.000 (406.4) 24.290 (616.97) F G 12.000 (304.8) 19.000 (482.6) H L C 20.500 (520.7) E D 21.000 (533.4) 5.000 (127) 5.000 (127) 10.500 (266.7) C 1.245 (31.75) A C L B G H 1 2.331 (59.21) 2 Description A . Wall plates B. Mounting brac...

Page 4 - Flat panel list

- 4 - Flat panel list Hitachi EIKI Electrograph Gateway 32HDT20,CMP307XJ,CMP307XU,32HDT20 CMP401HDU, CMP402HDE, CMP402HDU, CMP4120HDU,CMP4121,CMP4121HDU,CMP4201U, CMP4202U, 42HDW10,42HDT20, 42HDT50, 42HDT55 M6 x 12 CMP5000WXU, CMP5003WXU, 50HDT50, 50HDT55: M8 X 20 PLD42XU: M5 x 20 - ¼” nylon spacers...

Page 6 - Parts list; Actual screw size

- 6 - M4 x 25 M5 x 20 M5 x 50 M8 x 20 M6 x 30 (Qty 6) (Qty 4) (Qty 6) (Qty 4) (Qty 2) M4 x 16 (Qty 8) (Qty 8) M5 x 12 M5 x 16 (Qty 6) M5 x 25 (Qty 4) M6 x 12 (Qty 8) M8 x 25 (Qty 6) M8 x 30 (Qty 6) M8 x 35 (Qty 4) M6 x 20 (Qty 6) M8 x 70 (Qty 4) Parts list NOTE: This wall mount is shipped with all p...

Page 7 - Nylon sleeves; Nylon spacers and flat washers; NOTE: The nylon spacers may be staked to achieve proper spacing.

- 7 - 1/4" Nylon spacers 5/16" Flat washers (metal) 1" Nylon spacers 1/4" Nylon spacers 9/16" Nylon spacers (large) (small) 1/2" Nylon spacers (large) Nylon sleeves (Qty 6) (Qty 12) (Qty 6) (Qty 6) (Qty 6) (Qty 6) (Qty 4) Nylon spacers and flat washers actual size Parts list ...

Page 8 - Checking the thread depth on your flat panel; DO

- 8 - Checking the thread depth on your flat panel Inverted flat panel display Thread insert Thread depth indicator Figure 2 Figure 3 Figure 1 Marking the depth 1. Insert the thread depth indicator (supplied) through the thread inserts found on the back of the flat panel to make sure the inserts mea...

Page 10 - CL; Finding center of the flat panel display; Once the flat panel is inverted, use a measuring

- 10 - CL L C Finding center of the flat panel display Once the flat panel is inverted, use a measuring tape to find the center of your flat panel measuring from outside to outside of the chassis. See figure 1. Using a pencil lightly mark the center of your flat panel. See figure 2. Inverted flat pa...

Page 11 - Positioning the mounting brackets; Lay the left and right mounting

- 11 - Positioning the mounting brackets Inverted flat panel Nylon spacers if Applicable (see chart) on page 4 and 5 Center mark Bottom of flat panel CAUTION: Check the chart on page 4 and 5 to see if your flat panel needs nylon spacers. The nylon spacers provided, must be used. Failure to do so wil...

Page 13 - Securing the mounting brackets

- 13 - DIMPLES FACING UP DIMPLES FACING DOWN DIMPLES FACING UP DIMPLES FACING DOWN Securing the mounting brackets The Griplates™ have M4, M5 M6 and M8 hole patterns to fit the hardware that your flat panel requires. EXAMPLE: If your plasma uses M8 x 20 Phillip screws. Use the M8 mounting points. See...

Page 14 - Finding the wood studs behind the wall structure; (Look at the assembly drawing on page 3)

- 14 - 16" C EN TE R O F VI EW IN G H EI G H T D ES IR ED C EN TE R O F VI EW IN G H EI G H T D ES IR ED 16" 16" Finding the wood studs behind the wall structure Using a (commercially available) wood stud finder, locate the 16" or 24" stud centers behind the wall. Once found, mak...

Page 15 - Marking the bottom plate mounting points

- 15 - 16" 16" Marking the bottom plate mounting points Place the upper portion of the bottom wall plate to the reference line and mark the four (4) lag bolt mounting points through the wall plate slots on the wall. Level the wall plate with the reference arrow pointing up to the ceiling. Se...

Page 16 - Securing the bottom wall plate; When the bottom wall plate is properly; Level and secure the plate to the wall with; CAUTION: Do not over tighten the lag bolts.

- 16 - Securing the bottom wall plate When the bottom wall plate is properly installed to the wall. Lay the carton template on top of the wall plate. Lay the top wall plate on top of the cardboard template and mark the four (4) lag bolt mounting points. See figure 14. Wall plate (4) 5/16" x 3...

Page 17 - Securing the top plate

- 17 - Securing the top plate Drill four (4) ¼" pilot holes to the marked wall. See figure 15. Wall plate Wall marks

Page 18 - : CHECK THE MOUNT FOR PROPER

- 18 - Level and secure the plate to the wall with the reference arrow facing up to the ceiling. Secure the plate using the four (4) 5/16" lag bolts and flat washers (supplied). See figure 16 CAUTION: Do not over tighten the lag bolts. NOTE : CHECK THE MOUNT FOR PROPER TIGHTNESS AND SECURITY. Wa...

Page 19 - Securing the flat panel to the wall mount; TOP

- 19 - WARNING: AT LEAST (2) QUALIFIED PERSONNEL ARE STRONGLY RECOMMENDED FOR INSTALLATION OF THIS PRODUCT. FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY AND POSSIBLE DAMAGE TO THE FLAT PANEL. Securing the flat panel to the wall mount Raise the flat panel with the LEFT and RIGHT mounting brackets ...

Page 20 - Lateral shift

- 20 - Make any lateral shift adjustment and lock it by tightening the two (2) M6 x 30 (mm) Phillips screws found on the bottom of the mounting brackets. CAUTION: Do not over tighten the M6 screws to the rods. See figure 18 Lateral shift M6 x 30 Lateral shift screw

Page 21 - Lateral shift adjustment

- 21 - Tilt the flat panel and secure the two (2) M6 x 12 (mm) safety knobs to each of the mounting brackets. See figure 19. Lateral shift adjustment NOTE : To remove the display from the wall simply extend the display to its maximum tilt range, remove the two 6 (mm) safety knurl knobs push the flat...

Page 22 - USA and Canada –

- 22 - NORTH AMERICA EUROPE ASIA 3130 East Miraloma Avenue Anaheim, CA 92806 USA USA and Canada – Phone: 800-368-9700 Fax: 800-832-4888 Swallow House, Shilton Industrial Estate, Shilton, Coventry, England CV79JY Phone: +44 (0) 2476 614700 Fax: +44 (0) 2476 614710 Yabara 1916-15, Misato-machi, Gunma-...

LG PCM-MS2 - Manual

Table of Contents:

Summary

Other LG Models