Page 2 - Accessories; Thank you for purchasing this LGE product; IMPORTANT
Accessories Thank you for purchasing this LGE product Please make sure the following items are included with your monitor.If any items are missing, contact your dealer. OWNER'S MANUAL /Cards Power Cord (Depending on the country) 15-pin D-SUB Signal Cable (To set it up, this signal cable may be attac...
Page 3 - On Safety; The appliance coupler is used as the disconnect device.; Important Precautions
1 This unit has been engineered and manufactured to ensure your personal safety,however improper use may result in potential electrical shock or fire hazards. Inorder to allow the proper operation of all safeguards incorporated in this display,observe the following basic rules for its installation, ...
Page 4 - On Installation; Avoid high temperatures and humidity.
2 Important Precautions On Installation Do not allow anything to rest upon or roll over the power cord, and do not place thedisplay where the power cord is subject to damage. Do not use this display near water such as near a bathtub, washbowl, kitchen sink,laundry tub, in a wet basement, or near a s...
Page 5 - On Cleaning; screen because over-spraying may cause electrical shock.; On Repacking; your local authority.
3 Important Precautions On Cleaning Unplug the display before cleaning the face of the display screen.Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the display screen because over-spraying may cause electrical shock. When cleaning the product, unplug the power cord and scrub...
Page 6 - Connecting the Display; Important; Connecting the stand; Stand Base; Tie down the base lock to perpendicularity direction.; Stand Body
4 Connecting the Display Important This illustration depicts the general model of connection. Your monitor may differ fromthe items shown in the picture.Do not carry the product upside down holding only the stand base. The product mayfall and get damaged or injure your foot. Before setting up the mo...
Page 7 - Disassembling the stand; Place the monitor with its front facing downward on a soft cloth.; Turn the; Cable holder; in the direction of the arrow shown below to remove it.
5 Connecting the Display Disassembling the stand 3. Change your lock on the product as it follows and turn it in the arrow direction. If you can't release the stand base even the locking knob is at a releaseposition, Please push the indicated knob down and retry it. 1 . Place the monitor with its fr...
Page 8 - You can hurt your finger.
6 4. Pull out the stand to remove. 5. Pushing the PUSH button, take the stand base from stand body. Good Position Bad Position Warning: You can hurt your finger. Connecting the Display
Page 9 - computer system, and other attached devices is turned off.; Positioning your display; Tilt Range : -5 ̊ to 20 ̊; Ergonomic
77 Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Positioning your display 1. Adjust the position of the panel in various ways for maximum comfort. Tilt Range : -5˚ to 20˚ Ergonomic It is reco...
Page 10 - Connecting to the Computer; Press; NOTE
88 Connecting to the Computer 2. Press button on the front switch panel to turn the power on. When monitor power is turned on, the 'Self Image Setting Function' is executed automatically on D-SUB input. Connecting the Display Wall-outlet type signal input cables A B Connect D-SUB(RGB Analog) Cable (...
Page 11 - Connecting to the Computer Using LAN; Connect peripheral devices; Press button on the front switch panel to turn the power on.
99 Wall-outlet type signal input cables Connecting to the Computer Using LAN 1. Make sure to turn off the computer and product. Connect the cable as below sketch mapform to . 1 2 Connect peripheral devices Connect LAN Cable Connecting the Display Keyboard/Mouse Input LAN cable should be connected be...
Page 12 - To arrange the cables; to the cable holder.
10 Connecting the Display To arrange the cables Connect the power cord and the signal cable as shown in the figure and then fix them to the cable holder. 1. Open the cable holder and fix the cables inside the Cable holder . NOTE This picture shows how to organize cables generally and may look differ...
Page 13 - Control Panel Functions; MENU Button; Use this button to enter or exit the On Screen Display.; The message; MENU button; for several seconds. The message; Front Panel Controls; MUTE Button
11 11 Control Panel Functions MENU Button Use this button to enter or exit the On Screen Display. OSD LOCKED/UNLOCKED This function allows you to lock the current controlsettings, so that they cannot be inadvertently changed.Press and hold the MENU button for several seconds. The message "OSD LO...
Page 14 - Power Button; button before entering the On Screen; SOURCE; • LAN
12 12 Control Panel Functions This Indicator lights up blue when the displayoperates normally(On Mode). If the display is in SleepMode (Energy Saving), this indicator color changes to flicker. Power Button Power Indicator Use this button to enter a selection in the On Screen Display. AUTO/SETButton ...
Page 15 - On Screen Display (OSD) Control Adjustment; Screen Adjustment; MENU
13 13 On Screen Display (OSD) Control Adjustment Screen Adjustment Making adjustments to the image size, position and operatingparameters of the display is quick and easy with the On ScreenDisplay Control system. A short example is given below to familiarize you with the use of thecontrols. The foll...
Page 16 - PICTURE; On Screen Display(OSD) Selection and Adjustment; COLOR; The order of icons may differ depending on the model (14 to 19).
BRIGHTNESSCONTRASTGAMMA PICTURE 14 14 On Screen Display(OSD) Selection and Adjustment The following table indicates all the On Screen Display control, adjustment,and setting menus. Main menu Sub-menu Supported signals Description : LAN input LAN : D-SUB input D-SUB To adjust the brightness, contrast...
Page 17 - Press the MENU Button, then the main menu of the OSD appears.; Menu Name
15 15 On Screen Display(OSD) Selection and Adjustment NOTE OSD (On Screen Display) menu languages on the monitor may differ from the manual. You were introduced to the procedure of selecting and adjusting anitem using the OSD system. Listed below are the icons, iconnames, and icon descriptions of th...
Page 18 - To adjust the brightness of the screen.; Set your own red color levels.
16 16 On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description BRIGHTNESS CONTRAST GAMMA To adjust the brightness of the screen. To adjust the contrast of the screen. Set your own gamma value. : -50/0/50On the monitor, high gamma valuesdisplay whitish images and low gammavalues...
Page 19 - To adjust the clearness of the screen.; TRACKING; To move image left and right.
17 17 MENU : Exit : Decrease : Increase SET : Select another sub-menu On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description CLOCK PHASE SHARPNESS To minimize any vertical bars or stripesvisible on the screen background.The horizontal screen size will alsochange. To adjust th...
Page 20 - SETUP; ENABLE LAN; only when the input signal is a D-SUB or LAN input signal.
18 18 On Screen Display(OSD) Selection and Adjustment SETUP MENU : Exit : Adjust : Adjust SET : Select another sub-menu To choose the language in which thecontrol names are displayed. To adjust position of the OSD window onthe screen. LANGUAGE OSDPOSITION WHITEBALANCE FACTORYRESET If the output of t...
Page 21 - : For animation images in videos or movies
19 19 On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description MOVIEINTERNET NORMAL USER INTERNET : For text images (Word processing etc.) MOVIE : For animation images in videos or movies This is under normal operating conditions. This feature lets you easily select the best de...
Page 22 - Troubleshooting; Check the following before calling for service.
No image appears No image appears 20 20 Troubleshooting Check the following before calling for service. Do you see a "OSD LOCKED" message on the screen? ● Is the power cord of the display onnected? ● Is the power indicator light on? ● Is the power indicator flickering? ● Do you see an "O...
Page 23 - Display image is incorrect
21 21 Troubleshooting Display image is incorrect ● Display Position is incorrect. ● On the screen background, verticalbars or stripes arevisible. ● Any horizontal noise appearing in anyimage or charactersare not clearlyportrayed. • Press the AUTO/SET button to automatically adjust your display image...
Page 24 - The screen color is
22 22 Troubleshooting Display image is incorrect ● The screen color is mono or abnormal. ● The screen blinks. • Check if the signal cable is properly connected and use a screwdriver to fasten if necessary. • Make sure the video card is properly inserted in the slot. • Set the color setting higher th...
Page 25 - Specifications; Information in this document is subject to change without notice.
23 23 Specifications Display Sync Input Video Input Resolution Plug&Play PowerConsumption Dimensions & Weight Tilt Range Power Input Environmental Conditions Stand Base Power cord 48.133 cm (18.95 inch) Flat Panel Active matrix-TFT LCD,Anti-Glare coatingVisible diagonal size: 48.133 cm0.2835...
Page 26 - Indicator; LED Color
24 24 Specifications Preset Modes (Resolution) - D-SUB (Analog) Display Modes (Resolution) Horizontal Freq. (kHz) Vertical Freq. (Hz) *Recommend Mode Indicator On Mode Sleep Mode Off Mode Blue Flicker Off LED Color MODE 1234 *5 31.46931.46837.87948.36355.935 6070606060 640 x 480720 x 400800 x 600 10...
Page 27 - Rotate the; in the direction of the arrow to remove it.; Installing the Wall mount plate
Stand Base Head 25 This monitor satisfies the specifications of the Wall mount plate or theinterchange device. 3. Change your lock on the product as it follows and turn it in the arrow direction. If you can't release the stand base even the locking knob is at a releaseposition, Please push the indic...
Page 28 - Pull out the stand to remove.
26 Installing the Wall mount plate 4. Pull out the stand to remove. 5. Pushing the PUSH button, take the stand base from stand body. Good Position Bad Position Warning: You can hurt your finger.
Page 29 - Kensington Security Slot; Install the Wall mount plate.
27 27 Installing the Wall mount plate Wall mount plate(Separate purchase) This is stand-type or wall mount type and isconnectable with Wall mount plate.Please refer to the installation guide for moredetails, which is provided when Wall mount plateis purchased.LG recommends that wall mountingbe perfo...
