LG M2062DP - Manual - manualsarea.com

Page 2 - CONTENTS; TS

CONTENTS C O N TE N TS 2 PREPARATION FRONT PANEL CONTROLS ..............................4 BACK PANEL INFORMATION ............................5 STAND INSTALLATION ......................................6 DETACHING STAND ..........................................8 DETACHING STAND BODY ....................

Page 4 - PREPARATION; FRONT PANEL CONTROLS; Headphone Jack; Illuminates blue when the set is switched on.

4 PR EP A R AT IO N PREPARATION FRONT PANEL CONTROLS ■ This is a simplified representation of the front panel. The image shown may be somewhat different from your set. Headphone Jack IR receiver (Remote controller receiver)INPUT Button MENU Button OK Button VOLUME Button PROGRAMME Button Power Butto...

Page 5 - BACK PANEL INFORMATION

5 PR EP A R AT IO N ■ This is a simplified representation of the front panel. The image shown may be somewhat different from your set. BACK PANEL INFORMATION PCMCIA (PERSONAL COMPUTER MEMORY CARD INTERNATIONAL ASSOCIATION) CARD SLOT Insert the CI Module to PCMCIA CARD SLOT. (This feature is not avai...

Page 6 - PR; STAND INSTALLATION; ■ The image shown may be somewhat different from your set.; Stand Base

6 PREPARATION PR EP A R AT IO N STAND INSTALLATION ■ The image shown may be somewhat different from your set. Carefully place the product screen side down on a cushioned surface that will protect prod- uct and screen from damage. Insert the Stand Base into the product. Turn the Stand Base Lock throu...

Page 7 - stand base

7 PR EP A R AT IO N STAND INSTALLATION ■ The image shown may be somewhat different from your set. Carefully place the product screen side down on a cushioned surface that will protect product and screen from damage. Insert the stand base into the product. Use a Coin on the bottom of the stand base a...

Page 8 - DETACHING STAND; Latch

8 PREPARATION PR EP A R AT IO N DETACHING STAND ■ The image shown may be somewhat different from your set. <M1962DP/M2062DP/M2262DP/M2362DP> Place the set screen side down on a cushion or soft cloth. Detach the monitor to the Stand Base by turning the screw to the left. Turn the Stand Base Loc...

Page 9 - Coin

9 PR EP A R AT IO N DETACHING STAND ■ The image shown may be somewhat different from your set. 1 2 3 Place the set screen side down on a cushion or soft cloth. Pull the stand base. Detach the monitor to the Stand Base by turning the screw to the left.Turn the screw by using a Coin . <M2762DP> ...

Page 10 - DETACHING STAND BODY

10 PREPARATION PR EP A R AT IO N DETACHING STAND BODY ■ The image shown may be somewhat different from your set. ■ Remove the Stand Body in the same way as the following when using it as a Wall Hook. 1. Remove the screw 2 point.2. Pull the stand body. 1. Remove the screw 4 point.2. Pull the stand bo...

Page 11 - WALL MOUNT : HORIZONTAL INSTALLATION; Be sure to use screws and a wall mount that meet VESA standards.; Model

11 PR EP A R AT IO N WALL MOUNT : HORIZONTAL INSTALLATION For proper ventilation, allow a clearance of 10 cm on each side and from the wall. Detailed installationinstructions are available from your dealer, see the optional Tilt Wall Mounting Bracket Installation andSetup Guide. If you intend to mou...

Page 12 - DESKTOP PEDESTAL INSTALLATION

12 PREPARATION PR EP A R AT IO N DESKTOP PEDESTAL INSTALLATION POSITIONING YOUR DISPLAY For proper ventilation, allow a clearance of 10 cm on each side and from the wall. ■ The image shown may be somewhat different from your set. ■ The image shown may be somewhat different from your set.Adjust the p...

Page 13 - LOCATION; ■ When adjusting the angle of the screen, do not put your; WARNING

13 PR EP A R AT IO N LOCATION ■ When adjusting the angle of the screen, do not put your finger(s) in between the head of the monitor and the stand body. You can hurt your finger(s). Position your set so that no bright light or sunlight falls directly onto the screen. Care should be taken not to expo...

Page 14 - SECURING THE SET TO THE WALL TO PREVENT FALLING; NOTE; ► When moving the set, undo the cords first.

14 PREPARATION PR EP A R AT IO N SECURING THE SET TO THE WALL TO PREVENT FALLING WHEN THE SET IS USED ON A STAND (Only M2762DP) ■ The image shown may be somewhat different from your set. ■ Use a sturdy rope or cord (sold separately) to tie the product. It is safer to tie the rope so it becomes horiz...

Page 15 - Stand; ATTACHING THE TV TO A DESK (Only M2762DP)

15 PR EP A R AT IO N WARNING ■ The image shown may be somewhat different from your set.The SET must be attached to desk so it cannot be pulled in a forward/backward direction, potentially causinginjury or damaging the product. Use only an attached screw. 1-Screw (provided as parts of the product) St...

Page 16 - KENSINGTON SECURITY SYSTEM

16 PREPARATION PR EP A R AT IO N KENSINGTON SECURITY SYSTEM - The product is equipped with a Kensington Security System connector on the back panel. Connect the Kensington Security System cable as shown below. - For detailed installation and use of the Kensington Security System, refer to the user’s...

Page 17 - ANTENNA CONNECTION; ■ For optimum picture quality, adjust antenna direction.; EXTERNAL EQUIPMENT SETUP

17 EX TE R N A L E Q U IP M EN T S ET U P ANTENNA CONNECTION ■ To prevent damage do not connect to the mains outlet until all connections are made between the devices. ■ For optimum picture quality, adjust antenna direction. ■ An antenna cable and converter are not supplied. Multi-family Dwellings /...

Page 18 - EX; HD RECEIVER SETUP; Connecting with a component cable; Signal

18 EXTERNAL EQUIPMENT SETUP EX TE R N A L E Q U IP M EN T S ET U P HD RECEIVER SETUP Connecting with a component cable ■ To avoid damaging any equipment, never plug in any power cords until you have finished connecting all equipment. ■ The image shown may be somewhat different from your set. ► HDMI ...

Page 19 - Connecting a set-top box with a HDMI cable; HDMI

19 EX TE R N A L E Q U IP M EN T S ET U P Connecting a set-top box with a HDMI cable Connect the digital set-top box to HDMI/DVI IN jack on the SET Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.) Select HDMI input source using the INPUT button on the remot...

Page 20 - Connect the digital set-top box to; input source using the; INPUT; button on the remote control.; Connecting with an HDMI to DVI cable

20 EXTERNAL EQUIPMENT SETUP EX TE R N A L E Q U IP M EN T S ET U P Connect the digital set-top box to HDMI/DVI IN jack on the SET. Connect the audio output of the digital set-top box to the AUDIO IN (RGB/DVI) jack on the SET. Turn on the digital set-top box.(Refer to the owner’s manual for the digit...

Page 21 - DVD SETUP

21 EX TE R N A L E Q U IP M EN T S ET U P DVD SETUP Connecting with a component cable Connect the video outputs (Y, PB, PR) of the DVD to the COMPONENT IN VIDEO jacks on the SET. Connect the audio outputs of the DVD to the COMPONENT IN AUDIO jacks on the SET. Turn on the DVD player , insert a DVD. S...

Page 22 - Connecting with a Euro Scart cable; AV

22 EXTERNAL EQUIPMENT SETUP EX TE R N A L E Q U IP M EN T S ET U P Connecting with a Euro Scart cable Connect the Euro scart socket of the DVD to the AV IN Euro scart socket on the SET. Turn on the DVD player, insert a DVD. Select AV input source using the INPUT button on the remote control. Refer t...

Page 23 - Connecting the HDMI cable; IN

23 EX TE R N A L E Q U IP M EN T S ET U P Connecting the HDMI cable Connect the HDMI output of the DVD to the HDMI/DVI IN jack on the SET Select HDMI input source using the INPUT button on the remote control. Refer to the DVD player's manual for operating instructions. 1 2 3 NOTE ► Check that your H...

Page 24 - VCR SETUP; Connecting with a RF cable

24 EXTERNAL EQUIPMENT SETUP EX TE R N A L E Q U IP M EN T S ET U P VCR SETUP Connecting with a RF cable ■ To avoid picture noise (interference), allow adequate distance between the VCR and SET. Connect the ANT OUT socket of the VCR to the ANTENNA / CABLE IN socket on the SET. Connect the antenna cab...

Page 26 - INSERTION OF CI MODULE; Insert the CI Module to; PCMCIA; (Personal Computer Memory Card International Association); CARD SLOT; -This feature is not available in all countries.

26 EXTERNAL EQUIPMENT SETUP EX TE R N A L E Q U IP M EN T S ET U P INSERTION OF CI MODULE Insert the CI Module to PCMCIA (Personal Computer Memory Card International Association) CARD SLOT of SET as shown. For further information, see p.57 1 NOTE ► Check if the CI module is inserted into the PCMCIA ...

Page 27 - DIGITAL AUDIO OUT SETUP; Set the; “TV Speaker option - Off ”; CAUTION

27 EX TE R N A L E Q U IP M EN T S ET U P DIGITAL AUDIO OUT SETUP Connect one end of an optical cable to the TV Digital Audio (Optical) Output port. Connect the other end of the optical cable to the digital audio (Optical) input on the audio equipment. Set the “TV Speaker option - Off ” in the AUDIO...

Page 28 - USB SETUP; Connect the USB device to the; jacks on the side of SET.; USB IN

28 EXTERNAL EQUIPMENT SETUP EX TE R N A L E Q U IP M EN T S ET U P USB SETUP Connect the USB device to the USB IN jacks on the side of SET. After connecting the USB IN jacks, you use the USB function. (► p.109) 1 2 Memory Stick USB Cable

Page 29 - HEADPHONE SETUP; Plug the headphone into the; headphone; To adjust the; headphone volume; sound from the headphone is switched off.; ► AUDIO menu items are disabled when connecting a headphone.

29 EX TE R N A L E Q U IP M EN T S ET U P HEADPHONE SETUP Plug the headphone into the headphone socket. To adjust the headphone volume , press the + or - button. If you press the MUTE button, the sound from the headphone is switched off. 1 2 You can listen the sound through the headphone. NOTE ► AUD...

Page 30 - PC SETUP; When connecting with a D-sub 15 pin cable

30 EXTERNAL EQUIPMENT SETUP EX TE R N A L E Q U IP M EN T S ET U P PC SETUP When using the remote control, aim it at the remote control sensor on the SET. When connecting with a D-sub 15 pin cable Connect the signal cable from the monitor output socket of the PERSONAL COMPUTER to the PC inpu t socke...

Page 32 - Connecting with an HDMI to HDMI cable

32 EXTERNAL EQUIPMENT SETUP EX TE R N A L E Q U IP M EN T S ET U P Connecting with an HDMI to HDMI cable Connect the HDMI output of the PC to the HDMI/DVI IN jack on the SET. Turn on the PC and the SET. Select HDMI input source using the INPUT button on the remote control. 1 2 3 NOTE ► Check that yo...

Page 33 - BACK COVER FOR WIRE ARRANGEMENT

33 EX TE R N A L E Q U IP M EN T S ET U P BACK COVER FOR WIRE ARRANGEMENT Tie cables together with a cable management as shown in the illustration.

Page 34 - SUPPORTED DISPALY RESOLUTION

34 EXTERNAL EQUIPMENT SETUP EX TE R N A L E Q U IP M EN T S ET U P SUPPORTED DISPALY RESOLUTION RGB[PC] / HDMI[PC] mode Resolution Horizontal Frequency(kHz) Vertical Frequency(Hz) 640 x 480 31.469 59.94 640 x 480 37.5 75 800 x 600 37.879 60.317 800 x 600 46.875 75.0 1024 x 768 48.363 60.0 1280 x 768...

Page 35 - Component mode

35 EX TE R N A L E Q U IP M EN T S ET U P HDMI - DTV mode Component mode Resolution Horizontal Frequency(kHz) Vertical Frequency(Hz) 720 x 480 31.469 31.5 59.94 60 720 x 576 31.25 50 1280 x 720 37.500 50 1280 x 720 44.96 45 59.94 60 1920 x 1080 33.72 33.75 59.94 60 1920 x 1080 28.125 50.00 1920 x 10...

Page 36 - WATCHING TV / PROGRAMME CONTROL; AT; REMOTE CONTROL KEY FUNCTIONS; EXIT

36 WATCHING TV / PROGRAMME CONTROL W AT C H IN G T V / P R O G R A M M E C O N TR O L REMOTE CONTROL KEY FUNCTIONS When using the remote control, aim it at the remote control sensor on the set. ꔰ (POWER) ENERGY SAVING TV/PC INPUT TV/RAD Switches the set on from standby or off to standby. Adjust the ...

Page 38 - TURNING ON THE TV; ꕌꕍ; NUMBER; Initializing setup; Set Password; ꕌ ꕍ; MUTE

38 WATCHING TV / PROGRAMME CONTROL W AT C H IN G T V / P R O G R A M M E C O N TR O L TURNING ON THE TV -When your TV is turned on, you will be able to use its features. PROGRAMME SELECTION VOLUME ADJUSTMENT Firstly, connect the power cord correctly.At this stage, the TV switches to standby mode. In...

Page 39 - QUICK MENU; Aspect Ratio

39 W AT C H IN G T V / P R O G R A M M E C O N TR O L QUICK MENU Your TV's OSD (On Screen Display) may differ slightly from that shown in this manual. Q.Menu (Quick Menu) is a menu of features which users might use frequently. ꔣ Aspect Ratio : Selects your desired picture for- mat.For Zoom Setting, ...

Page 40 - ON SCREEN MENUS SELECTION AND ADJUSTMENT; MENU; CI Information

40 WATCHING TV / PROGRAMME CONTROL W AT C H IN G T V / P R O G R A M M E C O N TR O L ON SCREEN MENUS SELECTION AND ADJUSTMENT Your set's OSD (On Screen Display) may differ slightly from what is shown in this manual. SETUP SETUP Move Move Move OK OK OK OPTION PICTURE PICTURE LOCK AUDIO AUDIO TIME US...

Page 41 - AUTO PROGRAMME TUNING

41 W AT C H IN G T V / P R O G R A M M E C O N TR O L AUTO PROGRAMME TUNING Use this to automatically find and store all available programmes.When you start auto programming, all previously stored service information will be deleted.The maximum number of programmes that can be stored is 1000. But th...

Page 42 - If you want to select the

42 WATCHING TV / PROGRAMME CONTROL W AT C H IN G T V / P R O G R A M M E C O N TR O L If you want to select the Antenna, AUTO PROGRAMME TUNING DVB-C Auto Tuning is a menu for users in countries that support DVB cable.Use this to automatically find and store all available programmes.When you start au...

Page 45 - Country; in; Full; mode in; User; take a long time for tuning.; Note; ► DVB-C Cable may not operate correctly with some cable providers.

45 W AT C H IN G T V / P R O G R A M M E C O N TR O L To watch DVB-C in the countries excluding Finland, Sweden, Denmark and Norway select '- -' as the Country in OPTION. You can select User mode or Full mode in Auto Tuning. The corresponding home frequency information may need to be changed when tu...

Page 46 - OK; Service Operator

46 WATCHING TV / PROGRAMME CONTROL W AT C H IN G T V / P R O G R A M M E C O N TR O L CABLE DTV SETTING (IN CABLE MODE ONLY) The range that a user can select from the Service Operator menu differs depending on number of Service Operator supported by each country, and if number of supported Service O...

Page 47 - MANUAL PROGRAMME TUNING (IN DIGITAL MODE)

47 W AT C H IN G T V / P R O G R A M M E C O N TR O L MANUAL PROGRAMME TUNING (IN DIGITAL MODE) Manual Tuning lets you manually add a programme to your programme list. (For countries other than Finland, Sweden, Denmark and Norway & When selecting Antenna if Finland, Sweden, Denmark, Norway or “-...

Page 49 - MANUAL PROGRAMME TUNING (IN ANALOGUE MODE)

49 W AT C H IN G T V / P R O G R A M M E C O N TR O L • Use NUMBER buttons to input a 4-digit password in Lock System ‘On’ . • L : SECAM L/L (France) BG : PAL B/G, SECAM B/G (Europe / East Europe / Asia / New Zealand / M.East / Africa / Australia) I : PAL I/II (U.K. / Ireland / Hong Kong / South Afr...

Page 50 - Assigning a station name

50 WATCHING TV / PROGRAMME CONTROL W AT C H IN G T V / P R O G R A M M E C O N TR O L SETUP SETUP Move Move OK OK Auto TuningManual TuningProgramme EditSoftware Update : ON Diagnostics CI Information Auto TuningManual TuningProgramme EditSoftware Update : ON Diagnostics CI Information Manual Tuning ...

Page 51 - PROGRAMME EDIT

51 W AT C H IN G T V / P R O G R A M M E C O N TR O L • Press the MENU or EXIT button to close the menu window. • Press the BACK button to move to the previous menu screen. PROGRAMME EDIT When a programme number is skipped, it means that you will be unable to select it using P ꕌꕍ button during TV vi...

Page 52 - IN TV MODE

52 WATCHING TV / PROGRAMME CONTROL W AT C H IN G T V / P R O G R A M M E C O N TR O L IN DTV/RADIO MODE IN TV MODE ■ Skipping a programme number ■ Deleting a programme ■ Moving a programme 1 1 1 2 2 2 3 3 3 Turn the programme number to blue. Turn the programme number to red. Turn the programme numbe...

Page 53 - Skipping a programme number

53 W AT C H IN G T V / P R O G R A M M E C O N TR O L ■ Skipping a programme number ■ Auto Sort 1 1 2 3 Turn the programme number to blue. Release. Select a programme number to be skipped. Start Auto Sort. BLUE BLUE • When a programme number is skipped it means that you will be unable to select it u...

Page 54 - SOFTWARE UPDATE; Select; or; Off; that new software is found.

54 WATCHING TV / PROGRAMME CONTROL W AT C H IN G T V / P R O G R A M M E C O N TR O L SOFTWARE UPDATE Software Update means software can be downloaded through the digital terrestrial broadcasting system. SETUP SETUP Move Move OK OK Auto TuningManual TuningProgramme EditSoftware Update : ON Diagnosti...

Page 55 - * When setting “Software Update”

55 W AT C H IN G T V / P R O G R A M M E C O N TR O L * When setting “Software Update” Occasionally, a transmission of updated digital software infor- mation will result in the following menu on the TV screen. Simple Update: for current update stream Schedule Update: for scheduled update stream When...

Page 56 - DIAGNOSTICS; CH 30

56 WATCHING TV / PROGRAMME CONTROL W AT C H IN G T V / P R O G R A M M E C O N TR O L DIAGNOSTICS This function enables you to view information on the Manufacturer, Model/Type, Serial Number and Software Version. This displays the information and signal strength of the tuned *MUX. This displays the ...

Page 57 - BACK

57 W AT C H IN G T V / P R O G R A M M E C O N TR O L • Press the BACK button to move to the previous menu screen. CI [COMMON INTERFACE] INFORMATION This function enables you to watch some encrypted services (pay services). If you remove the CI Module, you cannot watch pay services. When the module ...

Page 58 - SELECTING THE PROGRAMME LIST; Mini Glossary; Displaying programme LIST

58 WATCHING TV / PROGRAMME CONTROL W AT C H IN G T V / P R O G R A M M E C O N TR O L SELECTING THE PROGRAMME LIST You can check which programmes are stored in the memory by displaying the programme list. • You may find some blue programmes. These have been set up to be skipped by auto program- ming...

Page 59 - FAVOURITE PROGRAMME SETUP; Selecting favourite programme; Displaying the favourite programme list

59 W AT C H IN G T V / P R O G R A M M E C O N TR O L FAVOURITE PROGRAMME SETUP Favourite programme is a convenient feature that lets you quikly scan up to programmes of your choice without having to wait for the TV to scan through all the in-between programmes. ■ Selecting favourite programme ◄ Fav...

Page 60 - INPUT LIST

60 WATCHING TV / PROGRAMME CONTROL W AT C H IN G T V / P R O G R A M M E C O N TR O L INPUT LIST HDMI, AV, COMPONENT and RGB can be recognized by a detect pin and thus enabled only when an external device approves voltage.By using TV/RAD button, you can move from External Input to RF Input and to th...

Page 61 - Select a programme

61 EP G (E LE CT RO NIC P RO G RA M M E G UID E)( IN D IG ITA L M O DE ) Select a programme Switch on/off EPG This system has an Electronic Programme Guide (EPG) to help your navigation through all the possible viewing options. The EPG supplies information such as programme listings, start and end t...

Page 62 - RED

62 EPG (ELECTRONIC PROGRAMME GUIDE) (IN DIGITAL MODE) EP G ( EL EC TR ON IC P RO GR AM M E G UID E)( IN D IG ITA L M OD E) Button Function in NOW/NEXT Guide Mode Button Function in 8 Day Guide Mode You can view a program being broadcasted and one scheduled to follow. RED RED GREEN BLUE BLUE YELLOW Y...

Page 65 - PICTURE CONTROL; Full Wide

65 PIC TU R E C O N TR O L You can watch the screen in various picture formats: 16:9, Just Scan, Original, Full Wide, 4:3, 14:9, Zoom and Cinema Zoom . If a fixed image is displayed on the screen for a long time, that fixed image may become imprinted on the screen and remain visible. You can adjust ...

Page 66 - PIC; • Zoom

66 PICTURE CONTROL PIC TU R E C O N TR O L • 4:3 The following selection will allow you to view a picture with an original 4:3 aspect ratio, gray bars will appear on both the left and right of the screen. • 14 : 9 You can view a picture format of 14:9 or a gen eral TV programme in the 14:9 mode. The...

Page 67 - PICTURE WIZARD; Expert 1

67 PIC TU R E C O N TR O L This feature lets you adjust the picture quality of the original image.Use this to calibrate the screen quality by adjusting the Black and White Level etc. General users can calibrate the screen quality by easily following each stage.When you adjust the image to Low, Recom...

Page 68 - ENERGY SAVING

68 PICTURE CONTROL PIC TU R E C O N TR O L It reduces the TV’s power consumption.The default factory setting is adjusted to the comfortable level to be viewed at home.You can increase the brightness of your screen by adjusting the Energy Saving level or by setting the Picture Mode. When adjusting En...

Page 69 - PRESET PICTURE SETTINGS

69 PIC TU R E C O N TR O L Vivid Strengthen the contrast, brightness, colour and sharpness for vivid picture. Standard The most general screen display status. Cinema Optimizes video for watching movies. Sport Optimizes video for watching sports events. Game Optimizes video for playing games. Picture...

Page 70 - Picture Mode-User option; MANUAL PICTURE ADJUSTMENT

70 PICTURE CONTROL PIC TU R E C O N TR O L Backlight To control the brightness of the screen, adjust the brightness of LCD panel. Adjusting the backlight when setting the brightness of the set is recommended. Contrast Adjusts the signal level between black and white in the picture. You may use Contr...

Page 71 - “Picture; PICTURE IMPROVEMENT TECHNOLOGY

71 PIC TU R E C O N TR O L You can calibrate the screen for each Picture Mode or set the video value according to the special video screen. You can set the video value differently for each input. To reset to the factory default screen after making adjustments to each video mode, execute the “Picture...

Page 72 - EXPERT PICTURE CONTROL

72 PICTURE CONTROL PIC TU R E C O N TR O L By segmenting categories, Expert 1 and Expert 2 provide more categories which users can set as they see fit, offering the optimal picture quality for users. This may also be used to help a professional optimize the TV performance using specific videos. EXPE...

Page 74 - Expert Pattern; ■ This is the pattern necessary for expert adjustment.; Colour Filter; adjust Red, Green or Blue according to each setting.; Colour Management; ■ As the tool used by the experts to make adjustments by using the

74 PICTURE CONTROL PIC TU R E C O N TR O L Expert Pattern (Off/Expert 1/Expert 2) ■ This is the pattern necessary for expert adjustment. ■ This function is enabled in "Picture Mode - Expert" when you watch DTV. Colour Filter (Off/Red/Green/Blue) ■ This is the function to filter the specific ...

Page 75 - PICTURE RESET

75 PIC TU R E C O N TR O L Settings of the selected picture modes BACK to the default factory settings. PICTURE RESET Move Move OK OK PICTURE PICTURE ▲ • Brightness 50 • Sharpness 70 • Colour 50 • Tint 0 • Colour Temperature 0 • Advanced Control • Picture Reset Screen ▲ • Brightness 50 • Sharpness 7...

Page 76 - Selecting Resolution; SCREEN SETUP FOR PC MODE

76 PICTURE CONTROL PIC TU R E C O N TR O L Selecting Resolution To view a normal picture, match the resolution of RGB mode and selection of PC mode.This function works in the following mode: RGB[PC] mode. <Vertical resolution : 768> <Vertical resolution : 900> SCREEN SETUP FOR PC MODE Mo...

Page 77 - Auto configure

77 PIC TU R E C O N TR O L Auto Configure (RGB [PC] mode only) Automatically adjusts picture position and minimizes image instability. After adjustment, if the image is still not correct, your set is functioning properly but needs further adjustment. Auto configure This function is for automatic adj...

Page 78 - Auto in progress

78 PICTURE CONTROL PIC TU R E C O N TR O L 2. Using Auto Config. (Remocon) This function is available for RGB signals only. <1600 x 900 Resolution> <1360 x 768 Resolution> <Others Resolution> <Others Resolution> <Others Resolution> <1920 x 1080 Resolution> Press A...

Page 79 - Adjustment for screen Position, Size, Phase

79 PIC TU R E C O N TR O L Adjustment for screen Position, Size, Phase If the picture is not clear after auto adjustment and especially if characters are still trembling, adjust the picture phase manually. This function works in the following mode: RGB[PC]. Move OK PICTURE ▲ • Brightness 50 • Sharpn...

Page 80 - Screen Reset; Phase

80 PICTURE CONTROL PIC TU R E C O N TR O L Screen Reset Returns Position, Size and Phase to the factory default settings. This function works in the following mode: RGB[PC]. Move OK PICTURE ▲ • Brightness 50 • Sharpness 70 • Colour 50 • Tint 0 • Colour Temperature 0 • Advanced Control • Picture Rese...

Page 81 - SO; SOUND CONTROL; AUTO VOLUME LEVELER

81 SO U N D C O N TR O L SOUND CONTROL 1 2 3 4 MENU Select Auto Volume. Select On or Off. Select AUDIO. • Press the MENU or EXIT button to close the menu window. • Press the BACK button to move to the previous menu screen. AVL automatically remains on the same level of volume if you change programme...

Page 82 - Adjustment for Clear Voice Level With selecting On; CLEAR VOICE II

82 SOUND CONTROL SO U N D C O N TR O L 1 2 4 3 5 MENU Select Clear Voice II. Select Level. Select On or Off. Make desired adjustment. Adjustment for Clear Voice Level With selecting On Select AUDIO. • Press the MENU or EXIT button to close the menu window. • Press the BACK button to move to the prev...

Page 83 - BALANCE

83 SO U N D C O N TR O L 1 2 3 MENU Select Balance. Make desired adjustment. Select AUDIO. • Press the MENU or EXIT button to close the menu window. • Press the BACK button to move to the previous menu screen. You can adjust the sound balance of the speakers to preferred levels. BALANCE Move Move OK...

Page 84 - PRESET SOUND SETTINGS-SOUND MODE

84 SOUND CONTROL SO U N D C O N TR O L 1 2 3 4 MENU • Press the MENU or EXIT button to close the menu window. • Press the BACK button to move to the previous menu screen. You can select your preferred sound setting; Standard, Music, Cinema, Sport or Game and you can also adjust the Treble, Bass . So...

Page 85 - PRESET SOUND SETTINGS-USER MODE

85 SO U N D C O N TR O L Move Move Move OK OK OK AUDIO AUDIO AUDIO Auto Volume : Off Clear Voice II : Off ꕅ3 Balance 0 Sound Mode : Standard • Surround X : Off • Treble 50 • Bass 50 • Reset ▼ Auto Volume : Off Clear Voice II : Off ꕅ3 Balance 0 Sound Mode : Standard • Surround X : Off • Treble 50 • B...

Page 86 - AUDIO RESET

86 SOUND CONTROL SO U N D C O N TR O L 1 2 3 MENU Select Reset. Initialize the adjusted value. Select AUDIO. • Press the MENU or EXIT button to close the menu window. • Press the BACK button to move to the previous menu screen. AUDIO RESET Move Move OK OK AUDIO AUDIO ▲ Sound Mode : Music • Surround ...

Page 87 - DIGITAL AUDIO OUT

87 SO U N D C O N TR O L 1 2 3 4 MENU Select Digital Audio Out. Select Auto or PCM. Select AUDIO. • Press the MENU or EXIT button to close the menu window. • Press the BACK button to move to the previous menu screen. DIGITAL AUDIO OUT Move Move OK OK AUDIO AUDIO ▲ Sound Mode : Music • Surround X : O...

Page 88 - TV SPEAKERS ON / OFF SETUP

88 SOUND CONTROL SO U N D C O N TR O L 1 2 3 4 MENU Select TV Speaker. Select On or Off. Select AUDIO. • Press the MENU or EXIT button to close the menu window. • Press the BACK button to move to the previous menu screen. TV SPEAKERS ON / OFF SETUP Move Move OK OK AUDIO AUDIO ▲ Sound Mode : Music • ...

Page 90 - Mono sound selection; DUAL I

90 SOUND CONTROL SO U N D C O N TR O L I/II Stereo/Dual Reception (In Analogue Mode Only) When a programme is selected, the sound information for the station appears with the programme num- ber and station name. ■ Mono sound selection If the stereo signal is weak in stereo reception, you can switch ...

Page 91 - Speaker Sound Output Selection

91 SO U N D C O N TR O L NICAM Reception (In Analogue Mode Only) Speaker Sound Output Selection If the TV is equipped with a receiver for NICAM reception, high quality NICAM (Near Instantaneous Companding Audio Multiplex) digital sound can be received. Sound output can be selected according to the t...

Page 92 - TIME SETTING; TIM; CLOCK SETUP; Time Zone

92 TIME SETTING TIM E S ET TIN G The clock is set automatically when receiving a digital signal. (You can set the clock manually only if the TV has no DTV signal.) You must set the time correctly before using on/off timer function. When you select a Time Zone city, the TV time is set by the time off...

Page 93 - AUTO ON/OFF TIME SETTING

93 TIM E S ET TIN G The Off time function automatically switches the TV to standby at a preset time.Two hours after the TV is switched on by the on time function it will automatically switch back to standby mode unless a button has been pressed. The Off time function overrides the On time function i...

Page 94 - SLEEP TIMER SETTING; Sleep Timer; in the

94 TIME SETTING TIM E S ET TIN G You do not have to remember to switch the TV off before you go to sleep.The sleep timer automatically switches the TV to standby after the preset time has elapsed. SLEEP TIMER SETTING • When you switch the TV off, the preset sleep timer is cancelled.• You can also ad...

Page 95 - OPTION SETTING; • If you want to change Language/ Country selection; ON-SCREEN MENU LANGUAGE / COUNTRY SELECTION

95 O PT IO N S ET TIN • When France is selected for Country, password is not '0' , '0' , '0' , '0' but '1' , '2' , '3' , '4' . OPTION SETTING The installation guide menu appears on the TV screen when it is switched on for the first time. • If you want to change Language/ Country selection ON-SCREEN ...

Page 96 - IO; LANGUAGE SELECTION (IN DIGITAL MODE ONLY); Audio Language OSD Information

96 OPTION SETTING O PT IO N S ET TIN The Audio function allows selection of a preferred language. If audio data in a selected language is not broadcast, the default language audio will be played.Use the Subtitle function when two or more subtitle languages are broadcast. If subtitle data in a select...

Page 97 - Adjustment for Audio Description Volume With selecting On

97 O PT IO N S ET TIN This function is for the blind, and provides explanatory audio describing the current situation in a TV programme in addition to the basic audio. When Audio Description On is selected, basic audio and Audio Description are provided only for those programmes that have Audio Desc...

Page 98 - DATA SERVICE

98 OPTION SETTING O PT IO N S ET TIN (This menu is enabled only in Ireland. ) This function allow users to choose between MHEG (Digital Teletext) and Teletext if both exist at the same time.If only one of them exists, either MHEG or Teletext is enabled regardless of which option you selected. DATA S...

Page 99 - INPUT LABEL

99 O PT IO N S ET TIN Selects a label for each input source. If you want to use HDMI-PC mode, you must set the input label to PC mode.(Refer to the below figure) INPUT LABEL 1 2 3 4 MENU Select Input Label. Select the source. Select the label. Select OPTION. OPTION OPTION OPTION Menu Language : Engl...

Page 100 - POWER INDICATOR

100 OPTION SETTING O PT IO N S ET TIN Select the power indicator on of off. Power indicator On - Normal Mode: Blue LED On.- Off Mode: LED Off Power indicator Off - Normal Mode: Blue LED Off.- Off Mode: LED Off POWER INDICATOR 1 2 3 4 MENU Select Power Indicator. Select On or Off. Select OPTION. OPTI...

Page 101 - DEMO MODE

101 O PT IO N S ET TIN Display the slide show to explain the various logo of this TV.It is not possible to use Demo Mode in Home Use mode. In Store Demo, Demo Mode is automatically set to On . Once Demo Mode is set to Off in Store Demo, Demo Mode does not run and only the screen is reset. The screen...

Page 102 - MODE SETTING

102 OPTION SETTING O PT IO N S ET TIN We recommend setting the TV to “Home Use” mode for the best picture in your home environment. “Store Demo” mode is an optimal setting for displaying at stores.. MODE SETTING 1 2 3 4 MENU Select Mode Setting. Select Store Demo or Home Use. Save. Select OPTION. OP...

Page 103 - INITIALIZING(RESET TO ORIGINAL FACTORY SETTINGS)

103 O PT IO N S ET TIN This function initializes all settings.But the settings of ꕋ Day and ꕋ Night of the Picture Mode cannot be initialized. It is useful to initialize the product or when you move to other city or country.When the Factory Reset is completed, you must restart the Initializing setup...

Page 104 - PARENTAL CONTROL / RATINGS; SET PASSWORD & LOCK SYSTEM

104 PA RE NT AL C O NT RO L / RA TIN G S PARENTAL CONTROL / RATINGS Enter the password, press ‘0’, ‘0’, ‘0’, ‘0’ on the remote control handset.When France is selected for Country, password is not ‘0’, ‘0’, ‘0’, ‘0’ but ‘1’,’2’,’3’,’4’.When France is selected for Country, password cannot be set as ‘0...

Page 105 - Lock System “On”; BLOCK PROGRAMME

105 PA RE NT AL C O NT RO L / RA TIN G S RADIO Blocks any programmes that you do not want to watch or that you do not want your children to watch. This function is available in Lock System “On” . Enter a password to watch a blocked programme. BLOCK PROGRAMME LOCK Move OK Set PasswordLock System : ON...

Page 107 - Lock System ”On”; INPUT BLOCK

107 PA RE NT AL C O NT RO L / RA TIN G S Save Enables you to block an input. It is available to use this function in Lock System ”On” . INPUT BLOCK LOCK LOCK Move Move OK OK Set PasswordLock System : ON • Block Programme • Parental Guidance • Input Block Key Lock : Off Set PasswordLock System : ON •...

Page 108 - KEY LOCK

108 PARENTAL CONTROL / RATINGS PA RE NT AL C O NT RO L / RA TIN G S LOCK LOCK Move Move OK OK Set PasswordLock System : Off • Block Programme • Parental Guidance • Input Block Key Lock : Off Set PasswordLock System : Off • Block Programme • Parental Guidance • Input Block Key Lock : Off Key Lock : O...

Page 109 - TO USE A USB DEVICE; WHEN CONNECTING A USB DEVICE; Music List, Photo Lis; When removing the USB device

109 TO U SE A U SB D EV IC E TO USE A USB DEVICE WHEN CONNECTING A USB DEVICE When you connect a USB device, this pop up menu is displayed, automatically.“POP UP MENU” will not be displayed while the OSD including Menu, EPG or Schedule list is activated or while the Bluetooth Headset is connected.Wh...

Page 110 - TO; Precautions when using the USB device

110 TO USE A USB DEVICE TO U SE A U SB D EV IC E Precautions when using the USB device ► Only a USB storage device is recognizable. ► If the USB storage device is connected through a USB hub, the device is not recognizable. ► A USB storage device using an automatic recognition programme may not be r...

Page 111 - Screen Components; Selec

111 TO U SE A U SB D EV IC E You can view photo files on USB storage device.The On Screen Display may be different from your TV. Images are an example to assist with the TV operation.When you are watching the photo by the Photo List function, you can not change the picture mode. Moves to upper level...

Page 112 - Photo Selection and PopUp Menu

112 TO USE A USB DEVICE TO U SE A U SB D EV IC E Photo List Page 2/3 Drive1 SGKIM001 1366x768, 125KB Up Folder Up Folder SG101 02/12/2010 SG102 02/12/2010 SGKIM001 02/12/2010 SGKIM002 02/12/2010 SGKIM003 02/12/2010 SGKIM004 02/12/2010 SG103 02/12/2010 SG104 02/12/2010 SG105 02/12/2010 SGKIM005 02/12...

Page 113 - How to view photo; PopUp

113 TO U SE A U SB D EV IC E How to view photo ➩ 1 2 3 5 4 Select the desired photos. Show the PopUp menu. Select View. The selected photo is displayed in full size. Select the target folder or drive. • Press the BACK button to move to the previous menu screen. • Use the P ꕌꕍ button to navigation in...

Page 115 - Using the Photo List function; ►When you select the

115 TO U SE A U SB D EV IC E Using the Photo List function ◄ 1/17 ► Slideshow ꘡ BGM ꘡ Delete Q.MENU Option Hide ꘤ Choose Options. Set Photo View Set Video. Set Audio. ꕉ Previous Set Photo View. Slide Speed Music Folder RepeatRandom Fast ◄ ► On ◄ ► Off ◄ ► ... ꕉ Previous 1 1 2 2 Select Set Photo View...

Page 116 - Show the

116 TO USE A USB DEVICE TO U SE A U SB D EV IC E Set Audio. Sound Mode • Auto Volume• Clear Voice II• Balance 0 Standrd ◄ ► Off ◄ ► Off ◄ ► ꕉ Previous 1 1 2 Make appropriate adjustments. (Refer to p. 81 to 85) Show the Sound Mode, Auto Volume, Clear Voice II, Balance. Make appropriate adjustments.(R...

Page 117 - Music List; MUSIC LIST

117 TO U SE A U SB D EV IC E Music List Page 2/3 Music SGKIM003 00:00/01:34 Up Folder Title Duration Up Folder SGKIM001 SGKIM002 SGKIM003 SGKIM004 SGKIM005 03:33 04:45 01:30 02:37 01:58 No Marked You can play music files on USB storage device.Purchased music files(*.MP3) may contain copyright restri...

Page 118 - Music Selection and PopUp Menu

118 TO USE A USB DEVICE TO U SE A U SB D EV IC E Music List Page 2/3 Music SGKIM003 00:00/01:34 Up Folder Title Duration Up Folder SGKIM001 SGKIM002 SGKIM003 SGKIM004 SGKIM005 03:33 04:45 01:30 02:37 01:58 No Marked Popup Menu Navigation Mark Page Change Exit MARK Music List Page 2/3 Music SGKIM003 ...

Page 119 - Using the Music List function, play

119 TO U SE A U SB D EV IC E ■ If you don't press any button for a while during the playing, the play information box (as shown in the below) will float as a screen saver. ■ The ‘ Screen Saver’ ? Screen saver is to prevent screen pixel damage due to an fixed image remaining on the screen for a exten...

Page 120 - Make appropriate adjustments.; ” is selected in; Repeat

120 TO USE A USB DEVICE TO U SE A U SB D EV IC E Set Audio Play. RepeatRandom ◄ On ► Off ꕉ Previous ►When you select the Set Audio Play, 1 2 Make appropriate adjustments. Show the Set Audio Play. • When “ Off ” is selected in Repeat menu, replay will stop once the last file in the list finishes play...

Page 121 - properly depending on the frame.; Energy Saving; key; MOVIE LIST

121 TO U SE A U SB D EV IC E You can play movie files on a USB storage device.The movie list is activated once USB is detected. It is used when playing movie files on TV.Displays the movies in the USB folder and supports Play.Allows playback of all movies in the folder and user desired files.It is a...

Page 122 - Movie List; Video Decoder

122 TO USE A USB DEVICE TO U SE A U SB D EV IC E Page 2/3 Movie SGKIM002 640x480, 720KB Up Folder Title Duration Up FolderFavorite MusicSGKIM001SGKM002SGKIM001SGKIM001 01:34:1501:35:3001:30:20 No Marked Movie List Popup Menu Navigation Mark Page Change Exit MARK F i l e Extension name Video Decoder ...

Page 123 - Movie Selection and PopUp Menu

123 TO U SE A U SB D EV IC E Page 2/3 Movie SGKIM002 640x480, 720KB Up Folder Title Duration Up FolderFavorite MusicSGKIM001SGKM002SGKIM001SGKIM001 01:34:1501:35:3001:30:20 No Marked Movie List Popup Menu Navigation Mark Page Change Exit MARK Page 2/3 Movie SGKIM002 640x480, 720KB Up Folder Title Du...

Page 124 - Using the Movie List function, play; Set Video Play, Set Video

124 TO USE A USB DEVICE TO U SE A U SB D EV IC E Using the Movie List function, play Q.MENU Option Choose Options. Set Video Play. Set Video. Set Audio. ꕉ Previous 1 2 Select Set Video Play, Set Video or Set Audio. Show the PopUp menu.

Page 125 - Audio Language & Subtitle Language; Picture Size, Audio Language

125 TO U SE A U SB D EV IC E ► Picture Size: Selects your desired picture format during movie play. ► Audio Language & Subtitle Language : Changes the Language Group of the audio/subtitle during movie play. ► Sync : Adjusts the time synchronisation of the subtitle from -10 secs to +10 secs by st...

Page 127 - Using the remote control; FF

127 TO U SE A U SB D EV IC E Using the remote control ◄◄ / ►► When playing, repeatedly, press the REW( ◄◄ ) button to speed up ◄◄ (x2) → ◄◄◄ (x4) → ◄◄◄◄ (x8) → ◄◄◄◄◄ (x16) → ◄◄◄◄◄◄ (x32) . repeatedly, press the FF( ►► ) button to speed up ►► (x2) → ►►► (x4) → ►►►► (x8) → ►►►►► (x16) → ►►►►►► (x32). ...

Page 128 - DIVX REGISTRATION CODE

128 TO USE A USB DEVICE TO U SE A U SB D EV IC E Confirm the DivX registration code number of the TV. Using the registration number, movies can be rented or purchased at www.divx.com/vod . With a DivX registration code from other TV, playback of rented or purchased DivX file is not allowed. (Only Di...

Page 129 - DEACTIVATION

129 TO U SE A U SB D EV IC E The purpose of deactivation is to allow deactivation of devices for users who have activated all the avail-able devices through the web server and are blocked from activating more devices. DivX VOD allowed the consumer to activate up to 6 devices under one account, but t...

Page 130 - TELETEXT; TOP TEXT

130 TE LE TE XT TELETEXT Teletext is a free service broadcast by most TV stations which gives up-to- the-minute information on news, weather, television programmes, share prices and many other topics.The teletext decoder of this TV can support the SIMPLE, TOP and FASTEXT systems. SIMPLE (standard te...

Page 131 - FASTEXT; Text Option

131 TE LE TE XT Press the T.OPT button and then use ꕌꕍ button to select ꔻ menu. Display the index page. You can select the pages which are colour coded along the bottom line with corresponding coloured buttons.AS with SIMPLE teletext mode, you can select a page by entering its three digit page numbe...

Page 132 - DIGITAL TELETEXT; TELETEXT WITHIN DIGITAL SERVICE

132 D IG ITA L T EL ET EX T DIGITAL TELETEXT The TV gives you access to digital teletext which is greatly improved in various aspects such as text, graphics etc.This digital teletext can access special digital teletext services and specific services which broadcast digital teletext. You should selec...

Page 133 - APPENDIX; TROUBLESHOOTING; The operation does not work normally.

133 A PP EN D IX APPENDIX TROUBLESHOOTING The operation does not work normally. The remote control doesn’t work ■ Check to see if there is any object between the product and the remote control causing obstruction. Ensure you are pointing the remote control directly at the set. ■ Ensure that the batt...

Page 134 - PP; The audio function does not work.

134 APPENDIX A PP EN D IX The audio function does not work. Picture OK & No sound ■ Press the + or - button. ■ Sound muted? Press MUTE button. ■ Try another channel. The problem may be with the broadcast. ■ Are the audio cables installed properly? No output from one of the speakers ■ Adjust Bala...

Page 135 - No image is displayed.; Only PC mode applied; There is a problem with PICTURE settings.

135 A PP EN D IX No image is displayed. Power is on, power indictor is blue but the screen appears extremely dark. ■ Adjust brightness and contrast again. Does the ‘Invalid format’ message appear? ■ The signal from the PC (Video card) is out of the vertical or horizontal frequency range of the produ...

Page 136 - Screen color is abnormal.

136 APPENDIX A PP EN D IX Screen color is abnormal. Screen has poor color res- oluion (16_colors). ■ Set screen color resolution to more than 24 bits (true color) Select control Pane → Display → Settings → Color Table menu in Windows. Screen color is unstable or mono color. ■ Check the connection st...

Page 137 - MAINTENANCE; then use it to wipe the screen.; Cleaning the Screen

137 A PP EN D IX MAINTENANCE Early malfunctions can be prevented. Careful and regular cleaning can prolong the life of your new set.Caution: Be sure to switch the power off and unplug the power cord before you begin any cleaning. A good way to keep the dust off your screen for a while is to wet a so...

Page 138 - PRODUCT SPECIFICATIONS

138 APPENDIX A PP EN D IX ■ The specifications shown above may be changed without prior notice for quality improvement. PRODUCT SPECIFICATIONS <M1962DP> LCD Panel S c r e e n Ty p e 470.1mm Wide (18.51 inch) TFT (Thin Film Transistor)LCD (Liquid Crystal Display) PanelVisible diagonal size: 470...

Page 143 - IR CODES; • This feature is not available for all models.

143 A PP EN D IX IR CODES • This feature is not available for all models. Code (Hexa) Function Note 95 Energy Saving R/C BUTTON 08 POWER R/C BUTTON (POWER ON/OFF) 50 TV / PC R/C BUTTON 0B INPUT R/C BUTTON 79 RATIO R/C BUTTON F0 TV/RAD R/C BUTTON 45 Q.MENU R/C BUTTON 43 MENU R/C BUTTON AB GUIDE R/C B...

Page 144 - EXTERNAL CONTROL DEVICE SETUP; RS-232C Configurations

144 APPENDIX A PP EN D IX EXTERNAL CONTROL DEVICE SETUP RS-232C Setup Connect the RS-232C (serial port) input jack to an external control device (such as a computer or an A/V control system) to control the product’s func- tions externally.Connect the serial port of the control device to the RS-232C ...

Page 146 - Communication Parameters; ■ Data length: 8 bits; Transmission / Receiving Protocol

146 APPENDIX A PP EN D IX Communication Parameters ■ Baud rate: 9600 bps (UART) ■ Data length: 8 bits ■ Parity : None ■ Stop bit: 1 bit ■ Communication code: ASCII code ■ Use a crossed (reverse) cable. Transmission * [Command 1] : First command to control the TV. (j, k, m or x) * [Command 2] : Secon...

Page 149 - ► To reduce the power consumption of the TV. You

149 A PP EN D IX 15. Balance (Command: k t) ► To adjust balance. You can also adjust balance in the AUDIO menu. Transmission Data Min : 00 to Max : 64 * Refer to ‘Real data mapping 1’. See page 150. [k][t][ ][Set ID][ ][Data][Cr] Ack [t][ ][Set ID][ ][OK/NG][Data][x] 16. Colour Temperature (Command:...

Page 152 - UK Only