LG LMV2031ST/00 Installation Manual

Page 2 - Your Safety First; BEFORE YOU START; • Proper installation is the installer's responsibility!; BE SURE TO READ THE FOLLOWING SAFETY INSTRUCTIONS:; • Avoid Electric Shock!; YOU COULD GET AN ELECTRIC SHOCK; • ELECTRICAL RATING OF THIS OVEN : 120V AC 60Hz.; For; • THIS APPLIANCE MUST BE GROUNDED!; W A R N I N G; or

– 2 – Your Safety First BEFORE YOU START • Proper installation is the installer's responsibility! Proper installation by a qualified technician or installer is recommended. NOTE: Vent grille appearance varies by model. BE SURE TO READ THE FOLLOWING SAFETY INSTRUCTIONS: • Avoid Electric Shock! – Befo...

Page 3 - • MAKE SURE YOU HAVE ENOUGH SPACE AND SUPPORT.; • DO NOT EXPOSE YOURSELF TO EXCESSIVE MICROWAVE ENERGY!; ow; Figure 4

Your Safety First • MAKE SURE YOU HAVE ENOUGH SPACE AND SUPPORT. – Mount the oven against a flat, vertical wall, so it is supported by the wall. The wall should be constructed of minimum 2" x 4" wood studding and 3/8" thick drywall or plaster/lath. – ATTACH (See note on page 4 ) the two ...

Page 4 - Actual Size; Two

– 4 – Parts, Tools, Materials THE FOLLOWING PARTS ARE SUPPLIED WITH THE OVEN: NOTE: Depending on your ventilation requirements, you may not use all of these parts. Damper/duct connector (for roof venting or wall venting installation) Not Actual Size (2 pieces must be assembled as shown) Not used if ...

Page 5 - Duct Tape

– 5 – Parts, Tools, Materials Clear Tape (for taping the templates to the wall) Phillips Screwdriver (for the screws) Gloves Pencil Flat Blade Screwdriver (for the toggle bolts) Plumb Line Measuring Tape (metal preferred) Duct Tape Caulking Gun and Caulk Stud Finder or Thin Nail Saber Saw (for cutti...

Page 6 - Prepare The Electrical Connection; This appliance MUST be grounded!; AVOID ELECTRIC SHOCK! THIS APPLIANCE MUST BE GROUNDED!; Upper

– 6 – STEP 1: Prepare The Electrical Connection Improper grounding could result in electric shock or other personal injury. 1. Locate the grounded electric outlet for this oven in the cabinet above the oven, as shown in Figure 5. NOTE: The outlet should be on a circuit dedicated to the microwave ove...

Page 7 - Prepare The Venting System; THIS OVEN MUST BE PROPERLY VENTED!

– 7 – STEP 2: Prepare The Venting System THIS OVEN MUST BE PROPERLY VENTED! NOTE: The ductwork you need for outside ventilation is not included with your oven. The standard ductwork fittings and length are shown in Figure 10, page 8 . You may vent your oven in one of three ways. However, do NOT vent...

Page 8 - Standard Fittings; must not; TOTAL LENGTH; TOTAL LENGTH; Examples

– 8 – STEP 2: Prepare The Venting System Standard Fittings NOTE: If the existing duct is round, you must use a rectangular-to-round adapter, with a rectangular 3" extension duct installed between the damper assembly and the adapter to prevent the exhaust damper’s sticking. Duct Length The total ...

Page 9 - Prepare The Venting Blower; ROO; ELECTRIC SHOCK HAZARD! UNPLUG UNIT BEFORE WORKING ON IT.; FIRE HAZARD! CORRECTLY INSTALL THE VENT FAN BEFORE USE; Figure 1

– 9 – STEP 3: Prepare The Venting Blower Your microwave oven is shipped with the blower assembled for roof - ve nting. You need to adjust the blower if you want wall-venting or room-venting installation. • DO NOT PULL OR STRETCH THE BLOWER WIRING! Pulling and stretching the blower wiring could resul...

Page 10 - ING

STEP 3: Prepare The Venting Blower WALL-VENT ING INSTALLATION: 1. Remove one or two blower unit mounting screw(s) and one or several blower plate mounting screw(s). Remove the blower plate from the cabinet. See Figure 1 3 . 2. Carefully lift the blower unit out of the microwave oven. 3. Use side cut...

Page 11 - Figure; Figure 2

STEP 3: Prepare The Venting Blower – 1 1 – ROOM-VENTING (Recirculating) INSTALLATION: 1. Remove one or two blower unit mounting screw(s) and one or several blower plate mounting screw(s). Remove the blower plate. See Figure2 1 . 2. Carefully lift the blower unit out of the microwave oven. 4 . Rotate...

Page 12 - Prepare The Wall & Upper Cabinet; Measure And Track/Tape Up The Templates; DO NOT ATTEMPT TO INSTALL THE MICRO-; CAUTION

– 1 2 – STEP 4: Prepare The Wall & Upper Cabinet To avoid personal injury or property damage, do not attempt to install this microwaveoven if you cannot find a wall stud. Consult a carpenter or contractor. Mounting Plate Measure And Track/Tape Up The Templates 1. Using a plumb line and (metal) m...

Page 13 - Drill The Holes In The Wall And Upper Cabinet.; To avoid risk of personal injury, electric shock or death:

– 1 3 – STEP 4: Prepare The Wall & Upper Cabinet Drill The Holes In The Wall And Upper Cabinet. 1. Drill holes on the circles. If there is a stud, drill a 3/16" hole for lag screws. If there is no stud, drill a 3/4" hole for togglebolts. Make sure to use at least 1 lag screw in a stud, a...

Page 14 - Install The Mounting Plate; The Oven Must Be Connected To At Least One

– 1 4 – STEP 5: Install The Mounting Plate C B A The Oven Must Be Connected To At Least One Wall Stud. 4. Attach the plate to the wall. To use spring toggle head bolts: Remove the toggle wings from the bolts. Insert the bolts into the mounting plate and replace the spring toggle head to 3/4 past the...

Page 15 - Attach The Oven To The Wall; Figure 3; ● Do not lift or support the product by the bottom center sur; ● Do not remove the packing tape on the slide-out vent during

STEP 6: Attach The Oven To The Wall 1. Carefully lift microwave oven and hang it on support tabs (See Figure 30 ) at the bottom of the mounting plate.Reaching through upper cabinet, thread power supply cord through the power supply cord hole in the bottom of the upper cabinet. See Figure 3 2 . 2. Ro...