Page 2 - On Safety; Do not Open the Display.; Important Precautions
A1 This unit has been engineered and manufactured to ensure your personalsafety, however improper use may result in potential electrical shock or firehazards. In order to allow the proper operation of all safeguardsincorporated in this display, observe the following basic rules for itsinstallation, ...
Page 3 - On Installation; screen because over-spraying may cause electrical shock.; On Repacking
A2 Important Precautions On Installation Do not allow anything to rest upon or roll over the power cord, and do not place thedisplay where the power cord is subject to damage. Do not use this display near water such as near a bathtub, washbowl, kitchen sink,laundry tub, in a wet basement, or near a ...
Page 4 - Connecting the Display; Important; Once you connect the stand base, try not to disconnect it.; Connecting the stand; Place the monitor with its front facing downward on a soft cloth.
A3 Connecting the Display Important This illustration depicts the general model of connection. Your monitor may differ fromthe items shown in the picture. Once you connect the stand base, try not to disconnect it. Do not carry the product upside down holding only the stand base. The product mayfall ...
Page 5 - Put a cushion or soft cloth on a flat surface.; To remove the Stand:; Place the monitor face down on
A4 Connecting the Display 1. Put a cushion or soft cloth on a flat surface. To remove the Stand: 2. Place the monitor face down on the cushion or soft cloth. 3. Hold the product as it follows and lift up the Stand slightly. 4. Change your hold on the product as it follows and turn the Stand Base in ...
Page 6 - To remove the Stand Base:
A5 Connecting the Display To remove the Stand Base: 2. Hold the body of the Stand as it follows. Type. A 3. Press inside the two long latches at the same time with your strength as it follows. 5. The body of the Stand and the Stand Base are successfully separated. 4. Keep pressing the two latches an...
Page 8 - Positioning your display; Ergonomic
A7 Connecting the Display 20 Before setting up the monitor, ensure that the power to the monitor, the computersystem, and other attached devices is turned off. Positioning your display 1. Adjust the position of the panel in various ways for maximum comfort. Tilt Range : -5˚~20˚ Ergonomic It is recom...
Page 9 - Using the Computer; Power Cord; Press button on the front switch panel to turn the power on.; NOTE
A8 2 1 Connecting the Display Using the Computer 1. Place the monitor in a convenient, well-ventilated location near your computer. 2. Connect the signal cable. When attached, tighten the thumbscrews to secure the connection. 3. Connect the power cord into a proper power outlet that is easily access...
Page 10 - Control Panel Functions; MENU Button; Use this button to enter or exit the On Screen Display.; Control; The message; MENU button; for several seconds. The message; Buttons; Front Panel Controls
A9 Control Panel Functions MENU Button Use this button to enter or exit the On Screen Display. Control Function OSD LOCKED/UNLOCKED This function allows you to lock the current controlsettings, so that they cannot be inadvertently changed.Press and hold the MENU button for several seconds. The messa...
Page 11 - Use this button to turn the display on or off.; Power Button; button before entering the On Screen
A10 Control Panel Functions This Indicator lights up blue when the displayoperates normally(On Mode). If the display is in SleepMode (Energy Saving), this indicator color changes to amber. Use this button to turn the display on or off. Power Button Power Indicator Use this button to enter a selectio...
Page 12 - On Screen Display (OSD) Control Adjustment; Screen Adjustment
A11 On Screen Display (OSD) Control Adjustment Screen Adjustment Making adjustments to the image size, position and operating parameters ofthe display is quick and easy with the On Screen Display Control system. A short example is given below to familiarize you with the use of the controls.The follo...
Page 13 - On Screen Display(OSD) Selection and Adjustment; PICTURE; POSITION VERTICAL; FLATRON
A12 NOTE The order of icons may differ depending on the model (A12~A17). On Screen Display(OSD) Selection and Adjustment The following table indicates all the On Screen Display control, adjustment,and setting menus. To adjust the brightness,contrast and gamma of thescreen PICTURE COLOR POSITION TRAC...
Page 14 - Press the MENU Button, then the main menu of the OSD appears.; P I C T U R E
A13 On Screen Display(OSD) Selection and Adjustment NOTE OSD (On Screen Display) menu languages on the monitor may differ from the manual. You were introduced to the procedure of selecting and adjusting an itemusing the OSD system. Listed below are the icons, icon names, and icondescriptions of the ...
Page 15 - Main menu
A14 On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description BRIGHTNESS CONTRAST GAMMA To adjust the brightness of the screen. To adjust the contrast of the screen. Set your own gamma value. : -50/0/50On the monitor, high gamma valuesdisplay whitish images and low gammavalues d...
Page 16 - To adjust the clearness of the screen.; TRACKING; To move image left and right.; POSITION
CLOCK PHASE SHARPNESS To minimize any vertical bars or stripesvisible on the screen background.The horizontal screen size will alsochange. To adjust the focus of the display. This item allows you to remove anyhorizontal noise and clear or sharpenthe image of characters. To adjust the clearness of th...
Page 17 - SETUP; LANGUAGE; Restore all factory default settings except; Press the button to reset immediately.; MENU; To select the image size of the screen.
A16 On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description If this does not improve the screen image, restore the factory default settings. If necessary, perform the white balance function again. This function will be enabled only whenthe input signal is an analog signal. SET...
Page 19 - Troubleshooting; Check the following before calling for service.; No image appears
A18 Troubleshooting No image appears Check the following before calling for service. No image appears Do you see a "OSD LOCKED" message on the screen? ● Is the power cord of the display connected? ● Is the power indicator light on? ● Is the power on and the power indicator blue orgreen? ● Is...
Page 20 - Display image is incorrect
A19 Troubleshooting Display image is incorrect ● Display Position is incorrect. ● On the screen background, verticalbars or stripes arevisible. ● Any horizontal noise appearing in anyimage or charactersare not clearlyportrayed. • Press the AUTO/SET button to automatically adjust your display image t...
Page 21 - Have you installed the display driver?; Have you installed the; The screen color is
A20 Troubleshooting Have you installed the display driver? ● Have you installed the display driver? ● Do you see an "Unrecognized monitor,Plug&Play (VESA DDC)monitor found"message? • Be sure to install the display driver from the display driver CD (or diskette) that comes with yourdispla...
Page 22 - Specifications; Information in this document is subject to change without notice.
A21 Specifications L194WS NOTE Information in this document is subject to change without notice. Display Sync Input Video Input Resolution Plug&Play PowerConsumption Dimensions &Weight Tilt RangePower Input Environmental Conditions Stand Base Power cord 19 inches (48.2 cm) Flat Panel Active ...
Page 24 - 9 inch monitor; Indicator; LED Color
A23 Specifications Preset Modes (Resolution) Display Modes (Resolution) Horizontal Freq. (kHz) Vertical Freq. (Hz) 123456789 1011121314 *15 16 640 x 350720 x 400640 x 480640 x 480800 x 600800 x 600832 x 624 1024 x 7681024 x 7681152 x 8701152 x 900 1280 x 10241280 x 1024 1440 x 9001440 x 9001440 x 90...
Page 25 - Installing the Wall mount plate
A24 Installing the Wall mount plate This monitor satisfies the specifications of the Wall mount plate orthe interchange device. 1. Put a cushion or soft cloth on a flat surface. 2. Place the monitor face down on the cushion or soft cloth. 3. Hold the product as it follows and lift up the Stand sligh...
Page 26 - Kensington Security Slot; Install the Wall mount plate.
A25 Installing the Wall mount plate Wall mount plate(Separate purchase) This is stand-type or will mount type and isconnectable with Wall mount plate.Please refer to the installation guide for moredetails, which is provided when Wall mount plate ispurchased. Kensington Security Slot Connected to a l...
Page 27 - Digitally yours
