Page 2 - On Safety; Do not Open the Display:; Important Precautions
1 This unit has been engineered and manufactured to ensure your personal safety,however improper use may result in potential electrical shock or fire hazards. Inorder to allow the proper operation of all safeguards incorporated in this display,observe the following basic rules for its installation, ...
Page 3 - On Installation; Avoid high temperatures and humidity.
2 Important Precautions On Installation Do not allow anything to rest upon or roll over the power cord, and do not place thedisplay where the power cord is subject to damage. Do not use this display near water such as near a bathtub, washbowl, kitchen sink,laundry tub, in a wet basement, or near a s...
Page 4 - On Cleaning; screen because over-spraying may cause electrical shock.; On Repacking; your local authority.
Important Precautions 3 On Cleaning Unplug the display before cleaning the face of the display screen.Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the display screen because over-spraying may cause electrical shock. When cleaning the product, unplug the power cord and scrub...
Page 5 - Accessories; NOTE
4 Accessories !!! Thank for selecting LGE products !!! Please make sure the following items are included with yourmonitor. If any items are missing, contact your dealer. User's Guide/Cards Power Cord 15-pin D-Sub Signal Cable (To set it up, this signal cable may be attached to this product before sh...
Page 6 - Connecting the Display; Connecting the stand; Important
Connecting the Display 5 Before setting up the monitor, ensure that the power to the monitor,the computer system, and other attached devices is turned off. Connecting the stand 1. Place the monitor with its front facing downward ona soft cloth. Check the direction of the Stand Base,and connect it in...
Page 7 - Disassembling the stand
6 Connecting the Display Disassembling the stand 1. Place the monitor with its front facing downward ona soft cloth. Nip Latch inside, Take off the stand basefrom stand body. When you desire to disintegrate themonitor from the stand base, use a cointo turn the screw counterclockwise. o r 2.
Page 8 - Positioning your display; ERGONOMIC
7 Connecting the Display Before setting up the monitor, ensure that the power to the monitor,the computer system, and other attached devices is turned off. Positioning your display -After installation, adjust the angle as shown below. 1. Adjust the position of the panel in various ways for maximum c...
Page 9 - Connecting with the PC
8 Connecting the Display E1940T/E2040T/E2240T/E2340T NOTE ‘ Self Image Setting Function’? This function provides the user with optimal display settings.When the user connects the monitor for the first time, this function automatically adjuststhe display to optimal settings for individual input signa...
Page 11 - Control Panel Functions; Front Panel Controls; MODE Button; PHOTO EFFECT; MENU Button; MENU button
10 Control Panel Functions E1940T/E2040T/E2240T/E2340T Front Panel Controls MODE Button Use this button to enter F-ENGINE , ORIGINAL RATIO, PHOTO EFFECT menus. For more information, refer to page 21. MENU Button OSD LOCKED/UNLOCKED This function allows you to lock the current controlsettings, so tha...
Page 12 - AUTO Button; AUTO IMAGE ADJUSTMENT; INPUT Button; EXIT Button
11 Control Panel Functions AUTO Button AUTO IMAGE ADJUSTMENT When adjusting your display settings, always pressthe AUTO button before entering the On Screen Display(OSD). (Only Analog Mode) This will automatically adjust your display image tothe ideal settings for the current screen resolutionsize (...
Page 15 - On Screen Display (OSD) Control Adjustment; Screen Adjustment; Button
14 On Screen Display (OSD) Control Adjustment E1940T/E2040T/E2240T/E2340T Screen Adjustment Making adjustments to the image size, position and operatingparameters of the display is quick and easy with the On ScreenDisplay Control system. A short example is given below to familiarize you with the use...
Page 17 - On Screen Display(OSD) Selection and Adjustment
16 On Screen Display(OSD) Selection and Adjustment The following table indicates all the On Screen Display control, adjustment,and setting menus. F-ENGINE ORIGINAL RATIO PHOTO EFFECT MODE To select or customize desiredimage settings DSUB DVI-D LANGUAGE POWER INDICATOR WHITE BALANCE FACTORY RESET To ...
Page 18 - Menu Name; Press the; MENU; Button, then the main menu of the OSD appears.
17 On Screen Display(OSD) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an itemusing the OSD system. Listed below are the icons, icon names, and icondescriptions of the all items shown on the Menu. Sub-menus NOTE OSD (On Screen Display) menu languages on th...
Page 20 - CLOCK; Exit
19 On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description CLOCK PHASE To minimize any vertical bars orstripes visible on the screenbackground.The horizontal screen size will alsochange. To adjust the focus of the display. This item allows you to remove anyhorizontal noise and...
Page 22 - MODE
21 On Screen Display(OSD) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an itemusing the OSD system. Listed below are the icons, icon names, and icondescriptions of the all items shown on the Menu. Sub-menus NOTE OSD (On Screen Display) menu languages on th...
Page 23 - NORMAL
22 On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description NORMAL Select this when you want to use the productin the most general using environment. MOVIE Select this when you are watching a video ormovie. INTERNET Select this when you are working on thedocument (Word etc.) DE...
Page 24 - WIDE
23 On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description Change the input image signal ratio tooriginal. WIDE ORIGINAL Switch to full screen mode according toinput image signal. * This function works only if inputresolution is lower than monitor ratio(16:9). Exit : Exit , : ...
Page 25 - SEPIA
24 On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description NORMAL The PhotoEffect function is disabled. GAUSSIANBLUR This menu changes the screen to be more colorful and smoother. SEPIA This menu changes the screen to be Sepia tone (brown color). MONOCH-ROME This menu changed ...
Page 26 - Troubleshooting; Check the following before calling for service.; No image appears
25 Troubleshooting No image appears Check the following before calling for service. No image appears Do you see a "OSD LOCKED" message on the screen? ● Is the power cord of the display connected? ● Is the power indicator light on? ● Is the power indicator blinking? ● Do you see an "OUT O...
Page 27 - Display image is incorrect
26 Troubleshooting Display image is incorrect ● Display Position is incorrect. ● On the screen background, verticalbars or stripes arevisible. ● Any horizontal noise appearing in anyimage or charactersare not clearlyportrayed. • Press the AUTO button to automatically adjust your display image to the...
Page 28 - The screen color is
27 Display image is incorrect Troubleshooting ● The screen color is mono or abnormal. ● The screen blinks. • Check if the signal cable is properly connected and use a screwdriver to fasten if necessary. • Make sure the video card is properly inserted in the slot. • Set the color setting higher than ...
Page 29 - Specifications
28 Specifications E1940T 47.0 cm (18.5 inch) Flat Panel Active matrix-TFT LCD Anti-Glare coating Visible diagonal size : 47.0 cm0.300 mm x 0.300 mm (Pixel pitch) Display Horizontal Freq. 30 kHz to 61 kHz (Automatic) Vertical Freq. 56 Hz to 75 Hz (Automatic) Input Form Separate Sync.Composite, Digita...
Page 38 - Indicator; LED Color
37 Specifications Indicator On Mode Sleep Mode Off Mode White White Blinking Off LED Color MODE Display Modes (Resolution) Horizontal Freq. (kHz) Vertical Freq. (Hz) *Recommend Mode E2240T/E2340T/E2240S/E2340S 123456789 1011 *12 720 x 400640 x 480640 x 480800 x 600800 x 600 1024 x 7681024 x 7681152 ...
