Page 2 - POWER CORD POLARIZATION:; This plug will fit into the power; REGULATORY INFORMATION:; WARNING
2 206-4118 MODEL and SERIAL NUMBERThe model and serial numbers of this TV are located on the back of the cabinet. For future reference, LG suggests that you record those numbers here: Model No._________________Serial No. _______________ WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COV...
Page 3 - Important safeguards for you and your new product; IMPORTANT SAFETY INSTRUCTIONS; Read all safety and operating instructions before oper-
3 206-4118 Important safeguards for you and your new product THIS PRODUCT HAS BEEN MANUFACTURED AND TESTED WITH SAFETY IN MIND. IMPROPER USE, HOWEVER, CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARDS. TO AVOID DEFEATING THE SAFEGUARDS THAT HAVE BEEN BUILT INTO THIS PRODUCT, PLEASE READ AND O...
Page 4 - This product should be operated only from the type of; Warning: To prevent fire or electrical shock; Antenna Grounding According to NEC, ANSI/NFPA 70
4 206-4118 IMPORTANT SAFETY INSTRUCTIONS (Continued from previous page) 19. Power Sources This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your installation, consult your product dealer or local powe...
Page 5 - References; otes; Commercial; Table of Contents
5 206-4118 Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2Important Safety Instructions . . . . . . . . . . . . . . . . . . . . 3–4Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Setup Checklist . . . . . . . . . . . . . . . . . . . . . ...
Page 6 - Setup Checklist; It may be advisable to make all
6 206-4118 Setup Checklist Installation and Setup Checklist __ Unpack TV and all accessories.__ Install batteries in remote control.__ Install TV on VESA mount or stand. Note: It may be advisable to make all hardwire connections before installing on VESA mount or stand, as appropriate. Hardware Conn...
Page 7 - Commercial Mode Setup for Master TV; This page provides an overview of a Master TV configuration.; ENTER; on the remote to exit the menu and save your changes.; Set Up TV Features; WXYZ; are set per your requirements. Set item
7 206-4118 Commercial Mode Setup for Master TV This page provides an overview of a Master TV configuration. Note: Disconnect all Aux inputs. Under certain conditions, Auto Tuning (Channel Search) is disabled if there is an Aux input active. Commercial Mode Setup Procedure1. Set Installer Menu Items ...
Page 8 - Installer Overview; This is the Commercial Mode Setup guide only.
8 206-4118 Installer Overview This is the Commercial Mode Setup guide only. Operating Installer Menu To set up the controls for the TV, you will need to know how to enter the TV Installer Menu and make changes to the default values as required. If necessary, familiarize yourself with the TV Installe...
Page 9 - Embedded; exam; Laptop
9 206-4118 Embedded b -LAN™ Module (EBL) FTG Mode of Operation Overview The following steps outline the FTG (Free-To-Guest) setup for individual TV control.1. Set up commercial features of the TV. Enter the Installer Menu, and set all desired items as required (for exam ple, Tuning Band, Start Chann...
Page 10 - ASPECT RATIO; To determine the operating mode of the TV, press; MENU; . If the Setup or TV Menu appears, the EBL is in Pass-Through
10 206-4118 CHANNEL PICTURE AUDIO TIME INPUT USB OPTION LOCK Typical TV Setup Menu Shows that the EBL is in Pass-Through Mode . You can also access this menu by turning IR Remote Access ON in the FTG Configuration Application, while the TV is in FTG Mode. End User “Aspect Ratio” or “Function” Menu S...
Page 11 - FTG Channel Map Overview
11 206-4118 DELETE Removes channel from lineup . ADD After inputting a new channel’s data, press to add channel to list. CHANNEL MAP EDITOR Shows both Channel Data and Logical Channel Lineup. EXIT Exits menu and returns to Logical Channel listing. LOGICAL CHANNEL NUMBERS Channels appear in numerical...
Page 12 - FTG Installer Menu Overview
12 206-4118 LEARN Press to transfer the Installer Menu settings on the TV to the EBL and PC FTG Configuration Application . INSTALLER DEFAULTS Press to re set FTG Installer Menu items to defaults. READ Press to transfer the Installer Menu values in the EBL to the PC FTG Configuration Application. WR...
Page 13 - FTG Operation Error Messages; Symptom; FTG Operation Troubleshooting
13 206-4118 The following table provides troubleshooting information for when EBL is configured in the FTG Mode of operation. FTG Operation Error Messages Symptom Probable Cause(s) Solution(s) Communication Error (“Communications Timeout”) Cable(s) not connected. Check and connect communication cabl...
Page 14 - Typical Installer Remote Control; Installing Batteries in Installer Remote; • Remove the battery compartment cover on the back side
14 206-4118 Typical Installer Remote Control The LG Installer Remote is supplied with and dedicated to oper-ate the TV. Some DVD and VCR controls may be available for selected LG DVD/VCR products. See next page for typical key functions in TV Mode and DVD/VCR Control. Follow the instructions provide...
Page 15 - Installer Remote Control Key Functions
15 206-4118 MARK Use to mark or unmark photos/music. RATIO Adjusts the picture aspect ratio. POWER Turns TV ON or OFF. MUTE Switches sound ON or OFF. VOLUME UP/DOWN Increases/decreases sound level. MENU Displays the Main Menu on the screen. Enters or exits on-screen menu system. VCR/DVD BUTTONS Cont...
Page 16 - Rear Connections Panel
16 206-4118 Rear Connections Panel AUDIO IN (RGB / DVI) Audio connection for either RGB or DVI device. COMPONENT IN Connect to output jacks on component device. HDMI/DVI PORT Connect to output jacks from HDMI/DVI device. TV-LINK CFG Use for local FTG configuration. SPEAKER OUT 8-OHM Connect to exter...
Page 17 - Side Connections Panel / RF Antenna Connection; AV IN 2; VIDEO IN; RF Antenna Connection; RF ANTENNA; Side Connections Panel; MPI PORT
17 206-4118 Side Connections Panel / RF Antenna Connection AV IN 2 L/MONO -A UDIO - R VIDEO USB IN VIDEO IN Connect to video output port on external device . L/MONO-AUDIO-R IN Connect to audio output jacks from external device.For mono audio output, connect to Left audio input. USB IN Insert USB dev...
Page 18 - RJP AVAILABLE; Remote Jack Pack Setup; JP PORT
18 206-4118 RJP Available? If you will use a Remote Jack Pack in your system, set Installer Menu item 093 RJP AVAILABLE appropriately (for exam- ple, on a legacy model RJP: HDMI Mode, set RJP AVAILABLE to 001). See Installer Menu detailed descriptions for further information. Remote Jack Pack Setup ...
Page 19 - TV Features Configuration Menus Overview; The on-screen menus control basic TV features.; Main TV Menus
19 206-4118 CHANNEL PICTURE AUDIO TIME INPUT USB OPTION LOCK TV Features Configuration Menus Overview The on-screen menus control basic TV features. Main TV Menus The Main TV Setup Menus control the features of the TV. Set the TV features to the desired configuration for the end user. Use the USB po...
Page 20 - MPI Learning Setup; These procedures assume that the TV is connected to a; TLL-1100A Cloning Connections / Learning Setup; se the TLL-1100A while any PPV card is installed
20 206-4118 Antenna (or CATV ) Antenna (or CATV ) TV LinkLoader-Demo TLL1100AReady TLL1100A ENTER RECEIVE SEND MENU MODE CLONE SELECTION MENUSelected Bank: CBankX Saved (1) LEARN FROM TV (2) TEACH TO TV(3) SET CLONE CLOCK FROM TV(4) SET TV CLOCK FROM CLONE(5) DISPLAY TV SETUP(6) DISPLAY CLONE SETUP ...
Page 21 - Before you begin cloning:; connect; LT2002 Cloning Connections / Learning Setup
21 206-4118 Before you begin cloning: • The Master TV should be connected to a good, stable signal from an over-the-air antenna or cable service analog channel and should also be connected to power (see above). • Teaching and Learning is only possible between identical model devices. (However, the L...
Page 22 - Learn Setup from Master TV; Learning the Master TV Setup
22 206-4118 Use the MPI Cable to Connect the LT2002 Clone Programmer to the Master TV MPI Port If there is a good connection, “THE CLONE HAS CONTROL OF THE TV” message will appear. Press any key on the Installer Remote. Learn Setup from Master TV Press 1 to select the LEARN FROM TV option; then pres...
Page 23 - Teach Master TV Setup to Target TV; or use; Disconnect TV Power for 15 Seconds; Teaching the Master Setup to Another TV; Connections for the LT2002 to Teach Another TV the Master Setup; LT2002 Cloning Connections / Teaching Setup; If an analog channel is not available, tune the TV to an Aux source,
23 206-4118 Teach Master TV Setup to Target TV After Learning is complete, remove the MPI cable from the Master TV, and connect it to the Target TV into which you wish to copy the Master TV Setup. With “THE CLONE HAS CONTROL OF TV” message displayed, press 2 or use either Channel key to select the T...
Page 24 - Accessing the Installer Menu; Using the Installer Menu; Installer Menu
24 206-4118 Use the Installer Menu to set up or change operational settings.See more detailed descriptions of the Installer Menu items on the pages that follow. Accessing the Installer Menu Make sure the TV is ON. Using a n Installer Remote, press MENU repeatedly until the on-screen menu locks up, a...
Page 26 - Detailed Descriptions of Installer Menu Items; 00 - INSTALLER SEQUENCE
26 206-4118 Detailed Descriptions of Installer Menu Items 000 - INSTALLER SEQUENCE Specifies entry sequence to the Installer Menu. 0 = 9876 1 = 4321 2 = 1478 3 = 3698 001 - POWER MANAGE (Power Management) Determines hours of no activity before automatic shutoff. The Power Management function is for ...
Page 27 - * Only affects Function Menu if enabled by some PPV providers.
27 206-4118 015 - SLEEP TIMER If set to 1, the Sleep Timer feature may be used. If set to 0, the Sleep Timer is not available. 016 - EN TIMER (Enable On/Off Timers) * If set to 1, the Timer function is available to the end user and enabled continuously. Set to 0 to disable On/Off Timers. Note: Clock...
Page 28 - • 0 = Remote jack pack is not available or disabled.
28 206-4118 Installer Menu (Cont.) 069 - EN. CH-T COL. (Enable Channel-Time Custom Color) Set to 1 to enable custom color for the Channel-Time display. Set to 0 to disable custom color for the Channel-Time display. 070 - FOR. CH-TIME (Channel-Time Display Foreground Color) Set according to Color Cha...
Page 30 - Reference: Detailed Instructions for Making a Master TV; Making a Master TV
30 206-4118 IMPORTANT INSTALLER SETUP INFORMATION! PLEASE READ THE FOLLOWING... To set up a Master TV, you will need to know how to enter the TV Installer Menu and make changes to the default values as required. If necessary, familiarize yourself with the Installer Menu and how to make and save chan...
Page 31 - XYZ; NETWORK
31 206-4118 Changing a Channel’s ICON on the Master TV 1. With Channel Up/Down, select the channel for which you wish to change the icon. 2. With the ADJ Left/Right arrow, select the thin letter “ I ” on the Channel ID display. 3. Use the Up/Down arrow keys to select the icon with which you want to ...
Page 32 - Checking the Software Version; You can check the software version of the; again to exit the Installer Menu.; Reference: Clonable Menu Features / Checking Software Version; Notes
32 206-4118 Checking the Software Version You can check the software version of the TV by accessing the Installer Menu. To do this, press MENU repeatedly until the on-screen menu locks up. Then, press 9-8-7-6 + ENTER . When you are finished, press ENTER again to exit the Installer Menu. Typical Inst...
Page 33 - Reference: USB End User Features; USB; NTER; Select the USB icon, and press; . Select the folder that contains
33 206-4118 Reference: USB End User Features Slideshow Toggles slideshow On and Off. Delete Removes slide from slideshow. Rotate Rotates picture. Background Music Toggles selected music file On and Off. USB USB Menu Features: Picture Slideshow with or without Music Accompaniment USB Device Setup On ...
Page 35 - On Target TV, Teach Master TV Profile
35 206-4118 Reference: USB Cloning / Master TV Profile Setup-Teaching On Target TV, Teach Master TV Profile 1. Plug the USB memory card with the Master TV profile setup into USB In port on the Target TV. 2. Press MENU to open the Main Menu. 3. Press the Left arrow key once to highlight the OPTION ic...
Page 36 - Reference: TV Camport Auto Sense Operation; Selectable; : Can be accessed with INPUT key, direct; Auto Sense; : Switches to this input when connector is insert-; CAMPORT (Front Video) Functionality Control
36 206-4118 Reference: TV Camport Auto Sense Operation The Camport Auto Sense function is enabled when:1. Installer Menu item 34 CAMPORT EN is set to 1 AND2. Installer Menu item 40 AUTO CAMPORT is enabled (1). Selectable : Can be accessed with INPUT key, direct access, etc. Auto Sense : Switches to ...
Page 37 - Reference: TV Aux Input Configuration
37 206-4118 Reference: TV Aux Input Configuration DIRECT ACCESS Tuning TV ENABLE MPI DATA START AUX SOURCE ASSIGNMENT Installer Menu MPI DATA STATUS TYPE 0x41 SOURCES ENABLED (R/W ) DATA STATUS TYPE 0xD2 CURRENT AV SOURCE (R) DATA STA- TUS TYPE 0x0D AUX SOURCE (R) OLD_OCV = 0 OLD_OCV = 1 Source Inpu...
Page 38 - Some Quick and Easy Tips for Resolving Problems; Reference: General Troubleshooting
38 206-4118 Some Quick and Easy Tips for Resolving Problems Software Problems Cannot direct enter channel number or “No Signal” appears. Channel not included in Channel Scan in TV controller. After 2-5-5 + MENU, only channels included in TV controller will appear. If channel is available, it can be ...
Page 39 - Clone Programmer; Reference: LT2002 Cloning Procedure Troubleshooting
39 206-4118 Reset Clone After Static Shock After replacing exhausted batteries, or if the Clone Programmer behaves strangely after a static shock, use a paper clip or similar instrument inserted through the small hole marked RESET to activate the internal reset switch and restore normal operation. A...
Page 40 - Reference: Troubleshooting Flow Chart
40 206-4118 Controller Quick Check Is STATUS LED on Analog Board Blinking? Plug into AC Power Outlet Is TV Connected to AC Power? Bad TV Yes No No Yes Is Red LED on TV Lit? 1. Bad Analog Board.2. Bad Digital Board. No Cycle the power by removingand re-connecting the ACpower cord. Observe thePOWER LE...
Page 41 - Reference: Commercial Mode Check
41 206-4118 Reference: Commercial Mode Check Press the On/Off key on the front panel. The ON/OFF key is always operational. Did you get a response? Bad TV Yes No Did TV stop responding or continue to respond? TV is in Commercial Mode. Stopped responding TV is not in Commercial Mode. Call Technical S...
Page 42 - -LAN will not be used, the installer can go
42 206-4118 Reference: b -LAN Setup & Overview Power to the b -LAN module is controlled by Installer Menu item 118 POWER SAVINGS. The default value is 003. The b -LAN module is only powered when the TV is turned ON. See chart below. The b -LAN module is internal to the TV. It allows the Hotel/In...
Page 43 - put Auto-sensing Hierarch; Digital Video In
43 206-4118 Reference: RJP Model List and Input Auto-sensing Hierarchy RJP Model List Legacy Models Scaler Models RJP-101M N/A RJP-101ML N/A RJP-110F RJP-210F RJP-110FW RJP-210FW RJP-110W RJP-210W RJP-110WBR RJP-210WBR RJP-110S RJP-210S RJP-120G RJP-220G RJP-120T RJP-220T RJP-201B RJP-301B RJP-202B ...
Page 44 - Reference: Glossary of Terms; A list of definitions for some of the words found in this guide.
44 206-4118 75 OHM RF CABLE The wire that comes from an off-air antenna or cable service provider. The end looks like a hex-shaped nut with a wire sticking through the middle. It screws onto the Antenna/Cable thread-ed jack on the back of the TV. 300 TO 75 OHM ADAPTER A small device that connects a ...
Page 45 - Document Revision History / Notes; Date; Revision A: New document; LCD TV
45 206-4118 Document Revision History / Notes Notes Document Revision History Date Description August 2009 Revision A: New document February 2010 Revision B: Enhanced b -LAN and Installer Menu description February 2010 Revision C: Includes LH260H and LH265H TVs Product documentation is av ailable on...
