Page 2 - SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL; P O W E R C O R D P O L A R I Z AT I O N :; WARNING; P A G E 2
RECORD Model and SERIAL NUMBERThe model and serial number of this TV is located on theback of the cabinet. For future reference, we suggest thatyou record those numbers here: Model No._________________Serial No. _______________ WA R N I N G : TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER ...
Page 3 - SAFETY INSTRUCTIONS; Important safeguards for you and your new product; IMPORTANT SAFETY INSTRUCTIONS; P A G E 3; Follow Instructions; All operating and use instructions should be followed.; Retain Instructions; PORTABLE CART WARNING
SAFETY INSTRUCTIONS Important safeguards for you and your new product This product has been manufactured and tested with safety in mind. However, improper use can result in potential electrical shockor fire hazards. To avoid defeating the safeguards that have been built into the new product, please ...
Page 4 - Outdoor Antenna Grounding; NEC - National Electrical Code
IMPORTANT SAFETY INSTRUCTIONS 206-4071 P A G E 4 (Continued from previous page) 14. Outdoor Antenna Grounding If an outside antenna or cable system is connected to theproduct, be sure the antenna or cable system is grounded so asto provide some protection against voltage surges and built-upstatic ch...
Page 5 - P A G E 5; Setup Checklist; References; Table of Contents; For Customer Support/Service please call:
P A G E 5 206-4071 Use this page as a reference to find pages or sections to go to and set up the TV features. Go to page 7 to begin the Commercial Mode Master TV setup. 1. Connect TV to RF signal and Auxiliary sources.2. Customize TV features and set up other operational controls in the Installer’s...
Page 6 - P A G E 6; Notes
Installation and Setup Checklist __ Unpack TV and all accessories.__ Install batteries in remote control.__ Make all connections to signal and Auxsources that will be available.__ Install TV on Vesa Mount or StandNote: It may be advisable to make all hard-wire connections before installing on Vesamo...
Page 7 - P A G E 7; Commercial Mode Setup for Master TV; WXYZ; OVERIDE
P A G E 7 Commercial Mode Setup for Master TV This page provides an overview of the TV configuration. See the pages referenced for morespecific, detailed instructions at each step; how to access and use the Installer menu etc. Note 1: Disconnect all Aux inputs. Under certain conditions, Auto Tuning ...
Page 8 - P A G E 8; Typical Connections Panel
206-4071 P A G E 8 Typical Connections Panel HDMI/DVI IN A V IN 1 COMPONENT IN USB IN SERVICE ONLY VIDEO AUDIO R-AUDIO-L (MONO) VIDEO R L RGB IN (PC) RS-232C IN SERVICE ONLY UPDATE RESET AUDIO IN (RGB / DVI) REMOTE CONTROL OUT SPEAKER OUT 8 C P B Y P R ..... ..... ..... ..... .... ...... .......... ...
Page 9 - V I D E O I N; RF Antenna Connection; R F A N T E N N A
P A G E 9 206-4071 A/V Input 2: Side Connections Panel / RF Antenna Connection AV IN 2 L/ MONO -AUDIO-R VIDEO H/P V I D E O I N Connect to video output port on external device . L / M O N O - A U D I O - R I N Connect to audio output jacks from external device. For only mono audio output, connect to...
Page 10 - MPI Card Slot; R F C A B L E; MPI Card Removal / PPV Card Installation
206-4071 P A G E 1 0 MPI Card Slot DC IN ANTENNA /CABLE M.P. I. M.P. I. Card Slot R F C A B L E RF cable needs to be dis-connected to remove cur-rent card . MPI Card Removal / PPV Card Installation 1. Remove the two MPI card retainer screws.2. Pull out current MPI card far enough so that the RF cabl...
Page 11 - Vesa Standard TV Mounts; Typical Pedestal Type Mount with
P A G E 1 1 206-4071 General Guidelines: Choosing aLocation for installing a VESA StandardMount To the right are some examples of VESA standardmounts. Since there are numerous types ofstands and mounts available, only a few areshown here. Refer to the instructions providedwith the TV stand that will...
Page 12 - Installer Overview; Operating Installer Menu; You will need an; LG Installer remote; control similar to the one; Typical Installer Menu
206-4071 P A G E 1 2 Installer Overview Operating Installer Menu To set up the controls for the TV you will need to know how to enterthe TV Installer menu and make changes to the default values. Ifnecessary, familiarize yourself with the TV Installer menu and how tomake and save changes to the items...
Page 13 - TV Overview; marily by qualified TV electronics technicians.
P A G E 1 3 206-4071 TV Overview Using the 32LG3DCH-UA Hospital TV, the patient has available the followingentertainment options. • Pillow Speaker control of TV.• Auxiliary inputs on side connections panel, if enabled.• Analog and Digital programming entertainment as provided by hospital: VHF, UHF, ...
Page 14 - Typical Installer Multi-Brand Remote Control; LG Multi-brand Remote Control; Installing Batteries in Installer Remote Control; • Remove the battery compartment cover on the back side by
206-4071 Typical Installer Multi-Brand Remote Control LG Multi-brand Remote Control Use the MODE button to select TV and put installer remote into TVoperating mode.Notes: This remote is not supplied with the TV. This typical LG multi-brand remote control is shown for reference. See next page for typ...
Page 15 - Installer Remote Control Typical Key Functions
TV INPUT/INPUT Select available input sources. POWER Turns your TV or any other programmed equipment On or Off, depending on mode. MULTI Selects RGB, HDMI,DVI, HDMI2 and Component Input sources. Adjusts picture brightness. EZ PIC Selects the factory preset picture appropriate for the viewing environ...
Page 16 - Pillow Speaker used in your system?; - For TV speakers sound with pillow; Pillow Speaker Setup; Pillow Speaker Control; Pillow Speaker Interface; Pillow Speaker Connections
206-4071 P A G E 1 6 1 2 3 4 5 6 3 1 5 2 4 6 TV ON/OFF OPEN CHAN UP/DATA IN COMMON AUDIO OUT CHAN DOWN Pillow Speaker used in your system? - Connect pillow speaker and slide con- trol switch to ‘Pillow Speaker’ to con-trol TV and hear audio on pillowspeaker. - For TV speakers sound with pillow speak...
Page 17 - Basic TV Features Setup
Basic TV Features Setup CHANNEL PICTURE AUDIO TIME OPTION LOCK CHANNEL PICTURE LOCK OPTION TIME Enter Move Enter Move Enter Move Enter Move Enter Move Aspect Ratio : 16:9 Picture Mode : Vivid - Backlight 100 -Contrast 100 - Brightness 50 - Sharpness 50 - Color 50 - Tint 0 Lock System :Off Set Passwo...
Page 18 - Channel Menu; CHANNEL; Channel Menu Navigation; Typical Menu Operation
Channel Menu The Channel menu contains the channel search and channel scanning setup options CHANNEL PICTURE AUDIO TIME OPTION LOCK CHANNEL Enter Move Auto Tuning Manual Tuning Channel Edit Channel Label Channel Menu Navigation Typical Menu Operation Auto Tuning (Channel Search) 1. Press Menu on the...
Page 19 - Picture Menu; PICTURE; Picture Menu Navigation; Picture Mode; Press Menu to remove Picture menu from; Sets the picture proportion.
P A G E 1 9 206-4071 Picture Menu The Picture menu settings control the appearance on the TV picture CHANNEL PICTURE AUDIO TIME OPTION LOCK PICTURE Enter Move Aspect Ratio : 16:9 Picture Mode : Vivid - Backlight 100 -Contrast 100 - Brightness 50 - Sharpness 50 - Color 50 - Tint 0 Advanced Control Re...
Page 20 - Audio Menu; The Audio menu configures the TV sound options; Audio Menu Navigation; Sound Mode; make custom sound settings.
206-4071 P A G E 2 0 Audio Menu The Audio menu configures the TV sound options CHANNEL PICTURE AUDIO TIME OPTION LOCK AUDIO Enter Move Clear Voice : Off Balance : 0 : Sound Mode : Standard - SRS TruSurround XT :Off - Treble 50 - Bass 50 - Reset TV Speaker: On/Off Auto Volume : Off Audio Menu Navigat...
Page 21 - Time Menu; The onscreen menus control the basic TV features; Time Menu Navigation; Sleep Timer; Set the internal clock on the TV automatically or manually.
P A G E 2 1 206-4071 Time Menu The onscreen menus control the basic TV features CHANNEL PICTURE AUDIO TIME OPTION LOCK TIME Enter Move Clock : - - - -, - - - - , - - : - - - - Off Time :Off On Time :Off Sleep Timer :Off Auto Sleep :Off Time Menu Navigation Typical Menu Operation Sleep Timer 1. Press...
Page 22 - Option Menu; OPTION; Option Menu Navigation; Caption; Press Menu to remove Option menu from screen.; captions will appear.
206-4071 P A G E 2 2 Option Menu The Option menu can be used to configure digital captions for the end user CHANNEL PICTURE AUDIO TIME OPTION LOCK OPTION Enter Move Language :English Caption : Off Option Menu Navigation Typical Menu Operation Caption Turns captions On/Off and enters submenus1. Press...
Page 23 - Lock Menu; The Lock menu can be used to set up V-Chip (Parental Control); Lock Menu Navigation; Lock System; Press Menu to remove Lock menu from screen.
P A G E 2 3 206-4071 Lock Menu The Lock menu can be used to set up V-Chip (Parental Control) CHANNEL PICTURE AUDIO TIME OPTION LOCK LOCK Enter Move Lock System :Off Set Password Block Channel Movie Rating TV Rating-Children TV Rating-General Downloadable Rating Input Block Lock Menu Navigation Typic...
Page 24 - Channel Banks Overview; Channel Bank Setup Menu
206-4071 P A G E 2 4 Channel Banks Overview Channel Banks Note: Disable all Aux sources in the Installer menu that will not be made available to the end user. Channel Banks Overview Purpose of Channel Banks: Allows the institution administrator to control access topatient in-room TV programming. A c...
Page 25 - Selects next higher channel number.; Shows currently selected Channel Bank.; Channel Banks Setup Installer Remote Control Key Functions; Channel Banks Setup Remote Control Key Functions
3140OSKZ003AR6 MUTE POWER BANK GUIDE CH PREVIEW SAP INFO CC OK VOL CH CH VOL FLASHBK TIMER ALARM MENU ADJ ADJ ADJ ADJ BED1 BED2 CH 011-001 NORMAL-ADDED Enter -> Change CC ->VCHIP Menu Ch. Preview -> Exit CHANNEL PREVIEW - BANK 1 Bank Selects channel banks 1-2-3-4. Ch Preview Selects channel...
Page 26 - A channel blanked, is blanked in all channel banks.; Selecting Deleted Channels; Channel Banks Setup
206-4071 Each channel bank is capable of storing broadcast digital and analog channels Figure 1. T ypical channel banks after running A uto Tuning BANK 1 2 3 4 A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A Purpose Chann el N u...
Page 27 - Reference: Channel Banks Worksheet
206-4071 PLAN Y OUR CHANNEL B ANKS B Y FILLING IN THESE CHARTS (or use photocopies) BANK 1 2 3 4 Purpose Channel N umber 1 2 3 4 5 6 7 8 9 1 0 11 1 2 13 1 4 15 1 6 17 1 8 19 2 0 21 2 2 23 2 4 2 BANK 1 2 3 4 Purpose Chann el N umber 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48...
Page 28 - Upgrading TV Software; Upgrading TV Software with USB Memory Card; On USB Memory Card; • Do not remove TV power cord or USB memory
206-4071 P A G E 2 8 Upgrading TV Software 1. Plug USB Memory Card into USB In port on TV.2. Menu should appear, if not press the Menu key.3. Use Up/Down arrow keys to navigate through the upgrades. Select the upgrade that you wantto install by highlighting it and pressing the Enter key. 4. Copying ...
Page 29 - On Target TV, Teach Master TV Profile; Master TV Profile Setup Learning/Teaching with USB Memory Card; On Master TV, Create Profile and Learn
P A G E 2 9 206-4071 On Target TV, Teach Master TV Profile 1. Plug USB memory card with Master TV Profile setup into Target TV USB In port. 2. Press Menu key to open Main menu and then highlight the Option Menu icon. 3. Press the Left arrow key once, this will highlight the Option icon on left side ...
Page 30 - It is assumed that the TV is connected to a signal source, the TV; TLL-1100A Clone Connections / Learning and Teaching Setups; On Master TV; Plug the other end of the MPI; On Target TV; Connect MPI cable from the TLL
206-4071 P A G E 3 0 Antenna (or CATV) Antenna (or CATV) TV LinkLoader-Demo TLL1100AReady TLL1100A ENTER RECEIVE SEND MENU MODE CLONE SELECTION MENUSelected Bank: CBank X Saved (1) LEARN FROM TV (2) TEACH TO TV(3) SET CLONE CLOCK FROM TV(4) SET TV CLOCK FROM CLONE(5) DISPLAY TV SETUP(6) DISPLAY CLON...
Page 31 - Turn to the next page to continue Cloning Setup.; Master TV; Cloning Connections/Learning Setup
Before you begin cloning... • The Master TV should be connected to a good, stable signal from an over-the-air antenna or cable service Analog channeland connected to power. (See above.) • Teaching and Learning is only possible between identical model TV/STBs. (However, the LT2002 Clone programmer ca...
Page 32 - Learn Setup from Master TV; LT2002 Clone Programmer Communication Problems; Learning the Master TV Setup; Cloning Learning Setup
Use MPI Cable to Connect LT2002 Clone Programmer toMaster TV MPI Port If there is a good connection, “THE CLONE HAS CONTROL OF TV” message will appear. Press any key on the Installer remote. Learn Setup from Master TV Press 1 to select the “LEARN FROM TV” option, then press ON/OFF,POWER, or ENTER to...
Page 33 - Target TV; Teaching the Master Setup to Another TV; Connections for the LT2002 to Teach another TV the Master Setup; Cloning Connections/Teaching Setup
P A G E 3 3 206-4071 Teach Master TV’s Setup to the target TV After learning is complete, remove the M.P.I. cable from themaster TV and connect it to the target TV that you want tocopy the master TV’s setup into. With “THE CLONE HASCONTROL OF TV” message displayed, press 2 or use eitherChannel key t...
Page 34 - Installer Menu
Use the Installer’s Menu to set up or change operational settings.See more detailed descriptions of the Installer menu items on the following pages... Accessing the Installer’s Menu Make sure TV is on. Installer’s menu items can be accessed by using an installer’s remotecontrol. Just press MENU repe...
Page 36 - Detailed Descriptions of Installer Menu Items; 00 - INSTALLER SEQUENCE; Specifies entry sequence to the Installer Menu.
P A G E 3 6 Detailed Descriptions of Installer Menu Items 000 - INSTALLER SEQUENCE Specifies entry sequence to the Installer Menu. 0 = 9876 1 = 4321 2 = 1478 3 = 3698 001 - POWER MANAGE (Power Management) Determines hours of no activity before automatic shutoff. The POWERMANAGE function is for savin...
Page 37 - * Only affects Function Menu if enabled by some PPV providers.; Set to 1 for operation with systems from On Command Corporation.
P A G E 3 7 206-4071-D 011 - KEY DEFEAT (Keyboard Defeat) If set to 1, key defeat prevents the end user from accessing the on-screen menus with the TV front panel—MENU, SELECT, and Left / Rightarrow keys do not function. If set to 0, those keys do function. NOTE: The menus can always be accessed by ...
Page 38 - Applies only to ‘Channel Not Available’ message if item 073 is
P A G E 3 8 206-4071 Installer Menu 035 - COMPPORT EN. (HDMI 1 Port Enable) Enable/disables TV display panel HDMI 1 input jack. Set to 0 to disable, set to 1 to enable. 038 - YPrPb EN. (Rear Component Video Enable) Set to 1 to enable display panel rear Component Video input jacks. Set to 0 to disabl...
Page 40 - LG Installer remote control; Reference: Detailed Information For Making A Master TV; Detailed Instructions; Clonable Menu Features
206-4071 IMPORTANT INSTALLER SETUP INFORMATION! PLEASE READ THE FOLLOWING... To set up a master TV you will need to know how toenter the TV Installer menu and make changes tothe default values as required. If necessary, famil-iarize yourself with the TV Installer menu and how to make and save change...
Page 41 - Editing/Adding Channel ICONs and/or Labels; XYZ; N E T W O R K
206-4071 P A G E 4 1 Changing a Channel’s ICON onMaster TV 1. With Channel Up/Down, select the channel you want to change the Icon for. 2. With the Right or Left ADJ arrow, select the letter ‘I’ on the channel ID display. 3. With the Up or Down arrow, select the desired ICON you want to appear to id...
Page 42 - Procedure for Checking Software Version; Reference: Clonable Menu Features; Reference: Checking Software Version
Procedure for Checking Software Version The software version of the TV may be checked by accessing the INSTALLER MENU. To do this, press the MENU button repeatedly until the menu display ceases to respond to MENU key presses. Then, press "9", "8", "7", "6", "ENTER...
Page 43 - USB Cloning Troubleshooting; If Upgrade Menu Does Not Appear
P A G E 4 3 206-4071 USB Cloning Troubleshooting If Upgrade Menu Does Not Appear 1. Go to the Option Menu.2. Highlight the Option Icon on the left side of menu.3. Press the number 7 key 7 times (7-7-7-7-7-7-7) then press ENTER.4. Upgrade Menu should appear. CHANNEL PICTURE AUDIO TIME OPTION LOCK OPT...
Page 44 - TV Camport Auto Sense Operation
P A G E 4 4 206-4071 TV Camport Auto Sense Operation The CAMPORT Auto Sense function is enabled when:1. Installer Menu Item 34, CAMPORT EN is set to 1 AND2. Installer Menu Item 40, AUTO CAMPORT is enabled (1). Selectable= Can be accessed with INPUT key, direct access, etc.Auto Sense= Switches to thi...
Page 46 - Some quick and easy tips to resolving problems; Symptoms; Power; Troubleshooting
P A G E 4 6 206-4071 Some quick and easy tips to resolving problems Symptoms Possible Cause(s) Possible Solution(s) Power No Power. See troubleshooting flow chart. TV Picture No Picture. • Display panel is turned off. -Turn TV on. -Power failure? • Antenna/Cable not connected. -Connect Antenna/Cable...
Page 47 - Problem; Reference: LT2002 Cloning Procedure Troubleshooting
P A G E 4 7 206-4071 Reset Clone After Static Shock After replacing exhausted batteries, or if the programmerbehaves strangely after a static shock, use a paper clip or simi-lar instrument inserted through the small hole marked ”RESET”to activate the internal reset switch and restore normal opera-ti...
Page 48 - Channel Banks Setup Troubleshooting; Channel Banks Setup Menu
P A G E 4 8 206-4071 Problem Solution Cannot change channel status in menu. Installer menu item 028 Ch Overide is set to 000. Set Ch Overide to 001 to allow access for channel status change. Channel Preview menu does not appear. 2-5-5+ Menu procedure was not performed. Channel Banks setup menu will ...
Page 49 - Troubleshooting Flow Chart
P A G E 4 9 206-4071 Controller Quick Check Is 'STATUS' LED on Analog Board Blinking ? Plug into AC Power Outlet Is TV Connected to AC Power ? Bad TV Yes No No Yes Is Red LED on TV Lit ? 1. Bad Analog Board.2. Bad Digital Board. No Cycle the power by removingand re-connecting the ACpower cord. Obser...
Page 50 - Commercial Mode Check
P A G E 5 0 206-4071 Commercial Mode Check Press the "On/Off" key on the front panel. The On/Off key is always operational. Did you get a response ? Bad TV Yes No Did TV stop responding or continue to respond ? TV is in Commercial Mode. Stopped responding TV is not in Commercial Mode Call Te...
Page 51 - Programming provided by a cable service.; Glossary of Terms; A list of definitions for some of the words found in this guide
206-4071 7 5 O H M R F C A B L E The wire that comes from an off-air antennaor cable service provider. The end looks likea hex-shaped nut with a wire stickingthrough the middle. It screws onto theAntenna/Cable threaded jack on the back ofthe TV. 3 0 0 TO 7 5 O H M A DA P T E R A s ma l l de v ic e t...
Page 52 - For Customer Support/Service Please call:
For Customer Support/Service Please call: 1-888-865-3026 www.lgcommercial.com © Copyright 2008, LG Electronics U.S.A., Inc. 206-4096 Issue-C Marketed and Distributed in the United States by LG Electronics U.S.A., Inc. 1000 Sylvan Avenue Englewood Cliffs, NJ 07632