Page 5 - Contents; iii
Contents Introduction . . . . . . . . . . . . . v Chapter 1. Important safety information 1 Chapter 2. Arranging your workspace . . 3 Comfort . . . . . . . . . . . . . . . . 3 Glare and lighting . . . . . . . . . . . . 3 Air circulation . . . . . . . . . . . . . . 4 Electrical outlets and cable leng...
Page 7 - Introduction
Introduction This User Guide contains the following information: v Chapter 1, “Important safety information,” on page 1 provides information about where to find safety information for this product. v Chapter 2, “Arranging your workspace,” on page 3 provides information about setting up your computer...
Page 11 - Comfort; Glare
Chapter 2. Arranging your workspace To get the most from your computer, arrange both the equipment you use and your work area to suit your needs and the kind of work you do. Your comfort is of foremost importance, but light sources, air circulation, and the location of electrical outlets can also af...
Page 13 - Connecting
Chapter 3. Setting up your computer Read and understand the Safety and Warranty Guide before you set up your computer. Reading and understanding the safety information reduces the risk of personal injury and or damage to your product. Set up your computer in the best possible work area that suits yo...
Page 18 - Important
Finishing the software installation Important Read the license agreements carefully before using the programs on this computer. These agreements detail your rights, obligations, and warranties for the software on this computer. By using these programs, you accept the terms of the agreements. If you ...
Page 19 - Hardware
Installing other operating systems If you install your own operating system, follow the instructions that come with your operating system CDs or diskettes. Remember to install all device drivers after you install your operating system. Installation instructions are usually provided with the device d...
Page 21 - features
v Wake on Ring (in the Setup Utility program, this feature is called Serial Port Ring Detect for an external modem) v Remote Administration v Automatic power-on startup v System Management (SM) BIOS and SM software v Ability to store power-on self-test (POST) hardware test results Input/output featu...
Page 45 - Basic
Chapter 7. Troubleshooting and diagnostics This chapter describes some basic troubleshooting and diagnostic programs. If your computer problem is not described here, see Chapter 9, “Getting information, help, and service,” on page 53 for additional troubleshooting resources. Basic troubleshooting Th...
Page 46 - Diagnostic; Use
Symptom Action The USB Keyboard does not work. Verify that: v The computer is turned on. v The keyboard is securely connected to a USB connector on the front or rear of the computer. v No keys are stuck. If you cannot correct the problem, have the computer serviced. Refer to the safety and warranty ...
Page 50 - mouse
Non-optical mouse The non-optical mouse uses a ball to navigate the pointer. If the pointer on the screen does not move smoothly with the mouse, you might need to clean the mouse. To clean the non-optical mouse: Note: The following illustration might be slightly different from your mouse. 1 Retainer...
Page 59 - Startup
Setting a rescue device in the startup sequence Before you start the Rescue and Recovery program from a CD, DVD, USB hard disk drive, or any external device, you must first change the startup sequence in the Setup Utility. To view or change the startup sequence, do the following: 1. With the compute...
Page 64 - Warranty
v Serial numbers of your hardware products v Description of the problem v Exact wording of any error messages v Hardware and software configuration information Using other services If you travel with your computer or relocate it to a country where your desktop or notebook computer machine type is so...
Page 65 - AT; bold
Appendix A. Manual modem commands The following section lists commands for manually programming your modem. Commands are accepted by the modem while it is in Command Mode. Your modem is automatically in Command Mode until you dial a number and establish a connection. Commands can be sent to your mod...
Page 68 - commands
Command Function &V1 Display Last Connection Statistics &W_ &W0 Stores the active profile as Profile 0 &W1 Stores the active profile as Profile 1 %E_ %E0 Disable auto-retrain %E1 Enable auto-retrain +MS? Displays the current Select Modulation settings +MS=? Displays a list of support...
Page 75 - Index
Index A access help 54 administration, password 32 advanced settings 34 antivirus software, updating 11 arranging workspace 3 AT commands basic 57 extended 59 audio subsystem 12, 15, 18, 21 B backup and recovery operations 46 basic trouble shooting 37 BIOS, updating (flashing) 35, 36 books folder, o...