Page 3 - Contents
Contents Important safety information . . . . . . v Service and upgrades . . . . . . . . . . . . . v Static electricity prevention . . . . . . . . . . . v Power cords and power adapters . . . . . . . . viExtension cords and related devices . . . . . . . viPlugs and outlets. . . . . . . . . . . . . ....
Page 4 - ii
Replacing the keyboard or mouse . . . . . 70 Completing the parts replacement . . . . . 71 Chapter 6. Recovery information . . . 73 Creating and using recovery media . . . . . . 73 Creating recovery media . . . . . . . . . 73 Using recovery media . . . . . . . . . . 74 Performing backup and recovery...
Page 5 - iii
Using other services . . . . . . . . . . 115 Purchasing additional services . . . . . . 115 Appendix A. Notices . . . . . . . . . 117 Trademarks . . . . . . . . . . . . . . . . 118 Appendix B. Regulatoryinformation . . . . . . . . . . . . . 119 Export classification notice . . . . . . . . . . 119 El...
Page 6 - iv
Page 7 - Important safety information; Warranty, and Setup Guide; Service and upgrades; Hazardous moving parts. Keep fingers and other body parts away.; Static electricity prevention
Important safety information CAUTION:Before using this manual, be sure to read and understand all the related safety information for thisproduct. Refer to the information in this section and the safety information in the ThinkStation Safety, Warranty, and Setup Guide that you received with this prod...
Page 8 - Power cords and power adapters; other countries, the suitable types shall be used accordingly.; Extension cords and related devices
or CRU, do not open the static-protective package containing the part until the instructions direct youto install it. When you handle options or CRUs, or perform any work inside the computer, take the following precautionsto avoid static-electricity damage: • Limit your movement. Movement can cause ...
Page 9 - materials or in explosive environments.; vii
Plugs and outlets If a receptacle (power outlet) that you intend to use with your computer equipment appears to be damagedor corroded, do not use the outlet until it is replaced by a qualified electrician. Do not bend or modify the plug. If the plug is damaged, contact the manufacturer to obtain a r...
Page 10 - viii
For your safety and to maintain optimum computer performance, always follow these basic precautionswith your desktop computer: • Keep the cover closed whenever the computer is plugged in. • Regularly inspect the outside of the computer for dust accumulation. • Remove dust from vents and any perforat...
Page 11 - Laser compliance statement; might result in hazardous radiation exposure.; Power supply statement; ix
Laser compliance statement CAUTION:When laser products (such as CD-ROMs, DVD drives, fiber optic devices, or transmitters) areinstalled, note the following: • Do not remove the covers. Removing the covers of the laser product could result in exposure to hazardous laser radiation. There are no servic...
Page 13 - Chapter 1. Product overview; Features
Chapter 1. Product overview This chapter provides information about the computer features, specifications, software programs providedby Lenovo, and locations of connectors, components, parts on the system board, and internal drives. Features This section introduces the computer features. The informa...
Page 16 - Preinstalled operating system; Your computer is preinstalled with the Microsoft
Your computer is preinstalled with software programs to help you work more easily and securely. For moreinformation, see “Software overview” on page 5. Preinstalled operating system Your computer is preinstalled with the Microsoft ® Windows ® 7 operating system. Operating system(s), certified or tes...
Page 17 - Specifications; Software overview
Specifications This section lists the physical specifications for your computer. Dimensions Width: 339 mm (13.35 inches) Height: 99.7 mm (3.93 inches) Depth: 381.1 mm (15.00 inches) Weight Maximum configuration as shipped: 7.5 kg (16.53 lb) Environment • Air temperature: Operating: 10°C to 35°C (50°...
Page 18 - Lenovo ThinkVantage Tools; Lenovo Welcome
Lenovo ThinkVantage Tools The Lenovo ThinkVantage ® Tools program guides you to a host of information sources and provides easy access to various tools to help you work more easily and securely. To access the Lenovo ThinkVantage Tools program, click Start ➙ All Programs ➙ Lenovo ThinkVantage Tools ....
Page 19 - Adobe Reader
Note: The SimpleTap program is only available on certain models preinstalled with the Windows 7 operating system. If your Windows 7 model is not preinstalled with the SimpleTap program, you can download itfrom http://www.lenovo.com/simpletap. ThinkVantage Password Manager The ThinkVantage Password M...
Page 21 - Locating connectors on the rear of your computer
Locating connectors on the rear of your computer Figure 2 “Rear connector locations” on page 9 shows the locations of the connectors on the rear of yourcomputer. Some connectors on the rear of your computer are color-coded to help you determine where toconnect the cables on your computer. Figure 2. ...
Page 23 - Locating components
Locating components Figure 3 “Component locations” on page 11 shows the locations of the various components in yourcomputer. To remove the computer cover, see “Opening the computer cover” on page 32. Figure 3. Component locations 1 Heat sink and fan assembly 7 System fan 2 Power supply assembly 8 In...
Page 24 - Locating parts on the system board
Locating parts on the system board Figure 4 “System board part locations” on page 12 shows the locations of the parts on the system board. 8 Figure 4. System board part locations 12 ThinkStation User Guide
Page 26 - Locating internal drives; • An optical drive in bay 1
Locating internal drives Internal drives are devices that your computer uses to read and store data. You can add drives to yourcomputer to increase storage capacity and enable your computer to read other types of media. Internaldrives are installed in bays. In this manual, the bays are referred to a...
Page 27 - Machine type and model label; The following is a sample of the machine type and model label.
Machine type and model label The machine type and model label identifies your computer. When you contact Lenovo for help, the machinetype and model information helps support technicians to identify your computer and provide faster service. The following is a sample of the machine type and model labe...
Page 29 - Chapter 2. Using your computer; Frequently asked questions
Chapter 2. Using your computer This chapter provides information on using some of the computer components. Frequently asked questions The following are a few tips that will help you optimize the use of your computer. Can I get my user guide in another language? The user guide is available in various...
Page 30 - Using the blue ThinkVantage button; The wheel mouse has the following controls:; Adjusting audio
Note: You can use the mouse or the Up and Down arrow keys to highlight menu selections. You can close the Start menu or the context menu by clicking the mouse or pressing Esc. Using the blue ThinkVantage button Some keyboards have a blue ThinkVantage button that you can use to open a comprehensive o...
Page 32 - Start
– Excessive vibration or sudden shock – An inclined surface – Direct sunlight • Do not insert any object other than a CD or DVD into the drive. • Before moving the computer, remove the CD or DVD from the drive. Handling and storing CD and DVD media CD and DVD media are durable and reliable, but they...
Page 35 - Chapter 3. You and your computer; Accessibility and comfort
Chapter 3. You and your computer This chapter provides information about accessibility, comfort, and relocating your computer to othercountries or regions. Accessibility and comfort Good ergonomic practice is important to get the most from your personal computer and to avoid discomfort.Arrange your ...
Page 36 - When arranging your workspace:
Adjust the monitor so the top of the screen is at, or slightly below, eye level. Place the monitor at acomfortable viewing distance, usually 51 to 61 cm (20 to 24 inches), and position it so you can view itwithout having to twist your body. Also, position other equipment you use regularly, such as t...
Page 37 - Registering your computer; To register your computer with Lenovo, do one of the following:; Moving your computer to another country or region; “Voltage-selection switch” on page 25; Voltage-selection switch
Registering your computer When you register your computer, information is entered into a database, which enables Lenovo to contactyou in case of a recall or other severe problem. After you register your computer with Lenovo, you will receivequicker service when you call Lenovo for help. In addition,...
Page 38 - Replacement power cords
Replacement power cords If you relocate your computer to a country or region that uses an electrical outlet style different from thetype you are currently using, you will have to purchase either electrical plug adapters or new power cords.You can order power cords directly from Lenovo. For power cor...
Page 39 - Security features; Security
Chapter 4. Security This chapter provides information about how to protect your computer from theft and unauthorized use. Security features The following security features are available on your computer: • Computrace Agent software embedded in firmware The Computrace Agent software is an IT asset ma...
Page 40 - Attaching an integrated cable lock; Kensington; Using passwords
Attaching an integrated cable lock An integrated cable lock, sometimes referred to as the Kensington lock, can be used to secure yourcomputer to a desk, table, or other non-permanent fixture. The cable lock attaches to the integrated cablelock slot at the rear of your computer and is operated with a...
Page 43 - Chapter 5. Installing or replacing hardware; Handling static-sensitive devices; • Do not place the part on the computer cover or other metal surface.; Installing or replacing hardware; Use only computer parts provided by Lenovo.; Installing external options
Chapter 5. Installing or replacing hardware This chapter provides instructions on how to install or replace hardware for your computer. Handling static-sensitive devices Do not open the static-protective package containing the new part until the defective part has been removedfrom the computer and y...
Page 44 - Opening the computer cover; To open the computer cover, do the following:; Removing and reinstalling the front bezel; To remove and reinstall the front bezel, do the following:
Opening the computer cover Attention: Do not open your computer or attempt any repair before reading and understanding the “Important safety information” on page v. This section provides instructions on how to open the computer cover. CAUTION: Turn off the computer and wait three to five minutes to ...
Page 45 - front bezel outward to remove it from the computer.
3. Remove the front bezel by releasing the three plastic tabs on the top of the front bezel and pivoting the front bezel outward to remove it from the computer. Figure 9. Removing the front bezel Chapter 5 . Installing or replacing hardware 33
Page 46 - Accessing the system board components and drives; To access the system board components and drives, do the following:
4. To reinstall the front bezel, align the other three plastic tabs on the bottom of the front bezel with the corresponding holes in the chassis, then pivot the front bezel inward until it snaps into position. Figure 10. Reinstalling the front bezel What to do next: • To work with another piece of h...
Page 47 - Installing or replacing a memory module; To install or replace a memory module, do the following:
Installing or replacing a memory module Attention: Do not open your computer or attempt any repair before reading and understanding the “Important safety information” on page v. This section provides instructions on how to install or replace a memory module. Your computer has four slots for installi...
Page 48 - module out of the memory slot.; want to install the memory module.
• If you are replacing an old memory module, open the retaining clips and gently pull the memory module out of the memory slot. Figure 11. Removing a memory module • If you are installing a memory module, open the retaining clips of the memory slot into which you want to install the memory module. F...
Page 49 - Installing or replacing a PCI card
10. Position the new memory module over the memory slot. Make sure that the notch 1 on the memory module aligns correctly with the slot key 2 on the system board. Push the memory module straight down into the slot until the retaining clips close. Figure 13. Installing a memory module What to do next...
Page 50 - amount until it is removed from the card slot.; Remove the new PCI card from its static-protective package.
Figure 14. Removing a PCI card Notes: a. The card fits tightly into the card slot. If necessary, alternate moving each side of the card a small amount until it is removed from the card slot. b. If the card is held in place by a retaining latch, disengage the card retaining latch in either of the two...
Page 51 - closed position. See “Locating parts on the system board” on page 12.; Installing or replacing the card reader; on page 39. For replacement, see “Replacing the card reader” on page 42.; Installing the card reader; To install the card reader, do the following:
6. Install the new card into the appropriate card slot on the system board and rotate the card retainer to the closed position. See “Locating parts on the system board” on page 12. Figure 16. Installing a PCI card What to do next: • To work with another piece of hardware, go to the appropriate secti...
Page 54 - Replacing the card reader; To replace the card reader, do the following:
Replacing the card reader To replace the card reader, do the following: 1. Remove all media from the drives and turn off all attached devices and the computer. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer. 2. Remove the compute...
Page 55 - the bracket with the corresponding hole in the chassis.
9. Install the card reader bracket to the chassis. Then push the bracket to the left to align the screw hole in the bracket with the corresponding hole in the chassis. Figure 21. Installing the card reader Chapter 5 . Installing or replacing hardware 43
Page 56 - parts on the system board” on page 12.; Replacing the battery
10. Install the screw to secure the card reader bracket to the chassis. Figure 22. Installing the screw that secures the card reader 11. Reconnect the card reader cable to one of the USB connectors on the system board. See “Locating parts on the system board” on page 12. 12. Pivot the optical drive ...
Page 57 - ThinkStation Safety, Warranty, and Setup Guide; Installing the solid state drive
Refer to the “Lithium battery notice” in the ThinkStation Safety, Warranty, and Setup Guide for information about replacing and disposing of the battery. To replace the battery, do the following: 1. Turn off the computer and disconnect all power cords from electrical outlets. 2. Open the computer co...
Page 58 - drive to the adapter.; and align pin
1. Install the solid state drive into the adapter. Then, install the four screws to secure the solid state drive to the adapter. Figure 25. Installing the solid state drive into the adapter 2. To install the solid state drive with the adapter into the 3.5-inch hard disk drive bracket, flex the brack...
Page 59 - Replacing the hard disk drive; To replace the primary hard disk drive, do the following:; disk drive from the chassis.
• To complete the installation or replacement, go to “Completing the parts replacement” on page 71. Replacing the hard disk drive Attention: Do not open your computer or attempt any repair before reading and understanding the “Important safety information” on page v. This section provides instructio...
Page 60 - on the bracket with the corresponding holes in the hard disk drive.
6. Flex the retaining clips as shown to remove the hard disk drive from the bracket. Figure 28. Removing the hard disk drive from the bracket 7. To install a new hard disk drive into the bracket, flex the bracket and align pin 1 , pin 2 , pin 4 , and pin 5 on the bracket with the corresponding holes...
Page 61 - Insert the two retaining clips; Replacing the optical drive; To replace an optical drive, do the following:
9. Insert the two retaining clips 1 of the hard disk drive bracket into the corresponding holes in the side of the optical drive bay, and then pivot the hard disk drive and bracket downwards until the harddisk drive bracket snaps into position. Figure 29. Installing the hard disk drive What to do ne...
Page 63 - Press the optical drive lock
7. Press the optical drive lock 1 and slide the optical drive out of the rear of the drive bay assembly. Figure 31. Removing the old optical drive 8. Install the optical drive retainer on the side of the new optical drive. Figure 32. Installing the optical drive retainer Chapter 5 . Installing or re...
Page 64 - Replacing the heat sink and fan assembly; To replace the heat sink and fan assembly, do the following:
9. Slide the new optical drive into the drive bay until it snaps into position. Figure 33. Installing a new optical drive 10. Connect the signal cable and the power cable to the rear of the optical drive. What to do next: • To work with another piece of hardware, go to the appropriate section. • To ...
Page 67 - Replacing the power supply assembly
10. Lower and position the heat sink fan duct on the top of the heat sink and fan assembly until it snaps into position. Figure 36. Installing the heat sink fan duct What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the installation or replacemen...
Page 68 - To replace the power supply assembly, do the following:
CAUTION: Hazardous moving parts. Keep fingers and other body parts away. CAUTION:Never remove the cover on a power supply or any part that has the following label attached. Hazardous voltage, current, and energy levels are present inside any component that has this labelattached. There are no servic...
Page 69 - fan duct out of the chassis.
5. Pivot the two plastic retaining clips that secure the heat sink fan duct outward, and then lift the heat sink fan duct out of the chassis. Figure 37. Removing the heat sink fan duct Chapter 5 . Installing or replacing hardware 57
Page 70 - power supply clip
6. Pivot the optical drive upward and disconnect the power supply assembly cables from all drives and from power connectors 1 , 2 and 3 on the system board. Figure 38. Power connectors on the system board Note: You might also need to release the power supply assembly cables from some cable clips or ...
Page 71 - Use only screws provided by Lenovo.
8. Ensure that the new power supply assembly is the correct replacement. 9. Install the new power supply assembly into the chassis so that the screw holes in the new power supply assembly are aligned with the corresponding holes in the rear of the chassis. Then, install the threescrews to secure the...
Page 72 - Replacing the microprocessor; To replace the microprocessor, do the following:
11. Lower and position the heat sink fan duct on the top of the heat sink and fan assembly until it snaps into position. Figure 41. Installing the heat sink fan duct What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the replacement, go to “Comple...
Page 74 - microprocessor in the socket.
b. Note the orientation of the microprocessor in the socket. You can either look for the small triangle 1 on one corner of the microprocessor or note the orientation of the notches 2 on the microprocessor. This is important when installing the new microprocessor on the system board. c. Touch only th...
Page 75 - fan assembly” on page 52.; Replacing the cover presence switch; To replace the cover presence switch, do the following:
12. Reinstall the heat sink and fan assembly with the fan duct as shown. See “Replacing the heat sink and fan assembly” on page 52. Figure 45. Reinstalling the heat sink and fan assembly with the fan duct 13. Reconnect all cables that were disconnected from the system board. What to do next: • To wo...
Page 76 - with the corresponding hole in the chassis.
6. Remove the screw that secures the cover presence switch and remove the cover presence switch from the chassis. Figure 46. Removing the cover presence switch 7. Position the new cover presence switch so that the screw hole in the cover presence switch is aligned with the corresponding hole in the ...
Page 77 - The internal speaker is only available in some models.
8. Install the screw to secure the cover presence switch to the chassis. Figure 47. Installing the new cover presence switch 9. Reconnect the cover presence switch cable to the system board. See “Locating parts on the system board” on page 12. 10. Reinstall the front bezel. See “Removing and reinsta...
Page 79 - as shown until it snaps into position.; Replacing the front audio and USB assembly
8. Align the new internal speaker with the two metal clips on the chassis, and then slide the speaker as shown until it snaps into position. Figure 49. Installing the new internal speaker 9. Reconnect the internal speaker cable to the system board. See “Locating parts on the system board” on page 12...
Page 81 - Replacing the system fan; To replace the system fan, do the following:
Replacing the system fan Attention: Do not open your computer or attempt any repair before reading and understanding the “Important safety information” on page v. This section provides instructions on how to replace the system fan. To replace the system fan, do the following: 1. Turn off the compute...
Page 82 - parts on the system board” on page 12; Replacing the keyboard or mouse; To replace the keyboard or mouse, do the following:
7. Install the new system fan by aligning the new rubber mounts that came with the new system fan with the corresponding holes in the chassis, and then push the rubber mounts through the holes. Then, carefullypull on the tips of the rubber mounts from the bottom until the new system fan is secured i...
Page 83 - Completing the parts replacement; of your computer” on page 9.; Obtaining device drivers
2. Connect a new keyboard or mouse to one of the USB connectors on the computer. Depending on where you want to connect the new keyboard or mouse, see “Locating connectors, controls, and indicators onthe front of your computer” on page 8 or “Locating connectors on the rear of your computer” on page ...
Page 85 - Chapter 6. Recovery information; Creating and using recovery media
Chapter 6. Recovery information This chapter provides information about the recovery solutions provided by Lenovo. This chapter contains the following topics: • Creating and using recovery media • Performing backup and recovery operations • Using the Rescue and Recovery workspace • Creating and usin...
Page 87 - the screen to complete the backup operation.; Performing a recovery operation; In the Rescue and Recovery main window, click the; Using the Rescue and Recovery workspace; To start the Rescue and Recovery workspace, do the following:
3. Click Back up your hard drive and select backup operation options. Then, follow the instructions on the screen to complete the backup operation. Performing a recovery operation This section provides instructions on how to perform a recovery operation using the Rescue and Recoveryprogram. To perfo...
Page 89 - Reinstalling preinstalled applications and device drivers; Reinstalling preinstalled applications
3. In the Please select boot device window, select the USB hard disk drive as the first boot device and press Enter. The rescue medium starts. When the rescue medium starts, the Rescue and Recovery workspace opens. The help information foreach feature is available from the Rescue and Recovery worksp...
Page 90 - Reinstalling software programs; To reinstall the program, do one of the following:; Reinstalling device drivers
Reinstalling software programs If a software program you installed on your computer is not working correctly, you might need to removeand reinstall it. Reinstalling overwrites the existing programs files and usually fixes any problems thatyou might have had with that program. To remove a program in ...
Page 93 - Chapter 7. Using the Setup Utility program; Starting the Setup Utility program; Exit; Viewing and changing settings
Chapter 7. Using the Setup Utility program The Setup Utility program is used to view and change the configuration settings of your computer, regardlessof which operating system you are using. However, the operating system settings might override any similarsettings in the Setup Utility program. Star...
Page 98 - Exiting the Setup Utility program
2. From the Setup Utility program main menu, select Power . 3. Select Intelligent Cooling Engine (ICE) . The Intelligent Cooling Engine (ICE) window is displayed. 4. Select ICE Thermal Alert . The ICE Thermal Alert window is displayed. 5. Select Enabled or Disabled as desired. 6. Press F10 to save c...
Page 99 - Chapter 8. Configuring RAID; RAID Level
Chapter 8. Configuring RAID This chapter provides information about how to configure Redundant Array of Independent Disks (RAID)for your computer. Note: The information about configuring RAID in this chapter is applicable only for a Windows environment. For information about configuring RAID in a Li...
Page 100 - Deleting RAID volumes; Delete RAID Volume; Resetting disks to non-RAID; Reset Disks to Non-RAID
7. Press Enter to initiate volume creation. 8. When prompted, press Y to accept the warning message and create the volume. 9. Return to step 2 to create additional RAID volumes, or select Exit and press Enter. 10. Press Y when prompted to confirm the exit. Deleting RAID volumes This section describe...
Page 101 - Chapter 9. Updating system programs; Using system programs; disc from the optical drive.
Chapter 9. Updating system programs This chapter provides information about updating the POST and BIOS, and how to recover from a POSTand BIOS update failure. Using system programs System programs are the basic layer of software built into your computer. System programs include thePOST, the BIOS, an...
Page 103 - Chapter 10. Preventing problems; Keeping your computer current
Chapter 10. Preventing problems This chapter provides information that can help you avoid common problems and keep your computerrunning smoothly. Keeping your computer current In some situations you may find it necessary to have the most current software programs, device drivers, oroperating system....
Page 104 - Using System Update; Cleaning and maintenance
Using System Update The System Update program helps you keep the software on your computer up-to-date. Update packagesare stored on Lenovo servers and can be downloaded from the Lenovo Support Web site. Update packagescan contain applications, device drivers, BIOS flashes, or software updates. When ...
Page 105 - Cleaning your computer; Computer; Cleaning a flat-panel monitor surface
Cleaning your computer It is a good practice to clean your computer periodically to protect the surfaces and ensure trouble-freeoperation. CAUTION:Be sure to turn off the computer and monitor power switches before cleaning the computer andmonitor screen. Computer Use only mild cleaning solutions and...
Page 106 - Cleaning a glass-screen surface; Good maintenance practices
Many computer supply stores carry the special cleaning fluids for displays. Use cleaning fluids developed forLCD displays only. First apply the fluid to a lint-free, soft cloth, then clean the LCD display. Some computersupply stores carry pre-moistened towelettes for LCD maintenance. Cleaning a glas...
Page 107 - Chapter 11. Troubleshooting and diagnostics; Basic troubleshooting; telephone numbers, refer to the
Chapter 11. Troubleshooting and diagnostics This chapter provides information about diagnosing and troubleshooting computer problems. If yourcomputer problem is not described here, see Chapter 12 “Getting information, help, and service” on page113 for additional troubleshooting resources. Basic trou...
Page 108 - Troubleshooting procedure; . If this does not correct the problem, continue with the next step.; Troubleshooting
Symptom Action The operating system does notstart. Verify that: • The startup sequence includes the device where the operating system resides. Usually, the operating system is on the hard disk drive. For more information,see “Selecting a startup device” on page 84. The computer beeps multipletimes b...
Page 109 - Audio problems; No audio in Windows; On
Select the problem your computer is experiencing from the following list: • “Audio problems” on page 97 • “CD problems” on page 98 • “DVD problems” on page 99 • “Intermittent problems” on page 101 • “Keyboard, mouse, or pointing device problems” on page 101 • “Monitor problems” on page 102 • “Networ...
Page 110 - CD problems
• Verify that the audio device drivers are correctly installed. See Microsoft Windows help system for more information. If these actions do not correct the problem, run the Lenovo Solution Center program. If you need technicalassistance, see Chapter 12 “Getting information, help, and service” on pag...
Page 111 - A CD or DVD does not work; DVD problems; Black screen instead of DVD video
• If you have multiple CD or DVD drives installed (or a combination of CD and DVD drives), try inserting the disc into the other drive. In some cases, only one of the drives is connected to the audio subsystem. • If you are using the Windows 7 operating system, follow the action for “A CD or DVD doe...
Page 113 - All or some keys on the keyboard do not work; The mouse or pointing device does not work
Intermittent problems Symptom: A problem occurs only occasionally and is difficult to repeat. Actions: • Verify that all cables and cords are securely connected to the computer and attached devices. • Verify that when the computer is on, the fan grill is not blocked (there is air flow around the gri...
Page 114 - Monitor problems
mouse, serial, or USB connector. Some keyboards have integrated USB connectors that can be usedfor a USB mouse or pointing device. • Verify that the device drivers for the mouse or pointing device are installed correctly. • If you are using a USB keyboard or mouse, verify that the USB connectors are...
Page 116 - The image is discolored; Networking problems; Ethernet problems
2. Adjust the placement of the monitor and other devices so that they are at least 305 mm (12 inches) apart. 3. Turn on the monitor. • You can reset the refresh rate through your operating system Control Panel. On the Windows 7 operating system, click Start ➙ Control Panel ➙ Hardware and Sound ➙ Adj...
Page 119 - Option problems; An option that was just installed does not work
PIM items sent from the Windows 7 operating system cannot be received correctly Symptom: Personal Information Manager (PIM) items sent from the Windows 7 operating system cannot bereceived correctly into the address book of any other Bluetooth-enabled device. Action: The Windows 7 operating system s...
Page 120 - Performance and lockup problems; Insufficient free hard disk drive space
Performance and lockup problems Poor performance and lockup problems can be a result of any of the following: • “Insufficient free hard disk drive space” on page 108 • “Excessive number of fragmented files” on page 108 • “Insufficient memory” on page 109 Make a selection from the above list to find ...
Page 121 - Insufficient memory; Printer problems
Action: Run the Windows Disk Defragmenter program. Note: Depending on the size of the hard disk drive and amount of data currently stored on the hard disk drive, the disk defragmentation process might take up to several hours to complete. On the Windows 7 operating system, do the following: 1. Close...
Page 122 - Software problems; When using a sort feature, dates do not sort in the correct order
• Make sure the serial cable is securely connected to the serial port on the computer and to the serial device. If the serial device has its own power cord, make sure it is attached to a properly grounded electrical outlet. • If the serial device has its own On/Off switch, make sure it is in the On ...
Page 126 - Problem determination
Lenovo Support Web site Technical support information is available on the Lenovo Support Web site at:http://www.lenovo.com/support This Web site is updated with the latest support information such as the following: • Drivers and software • Diagnostic solutions • Product and service warranty • Produc...
Page 127 - Using other services; Warranty; , and follow the instructions on the screen.; Purchasing additional services
• Installation and maintenance of application programs Refer to the ThinkStation Safety, Warranty, and Setup Guide that comes with your computer for information about your warranty type and duration. You must retain your proof of purchase to obtain warranty service. For a list of the Lenovo Support ...
Page 130 - Trademarks
Trademarks The following terms are trademarks of Lenovo in the United States, other countries, or both: LenovoThe Lenovo logoRescue and RecoveryThinkStationThinkVantage Microsoft, Windows, and Windows Vista are trademarks of the Microsoft group of companies. Celeron, Intel, Intel Core, Pentium, and ...
Page 131 - Appendix B. Regulatory information; Export classification notice; Industry Canada Class B emission compliance statement; This Class B digital apparatus complies with Canadian ICES-003.
Appendix B. Regulatory information Export classification notice This product is subject to the United States Export Administration Regulations (EAR) and has an ExportClassification Control Number (ECCN) of 4A994.b. It can be re-exported except to any of the embargoedcountries in the EAR E1 country l...
Page 133 - Additional regulatory information; For additional regulatory information, refer to the; User Guides & Manuals
Japanese VCCI Class B statement Japan compliance statement for products which connect to the power mains with rated currentless than or equal to 20 A per phase Lenovo product service information for Taiwan Keyboard and mouse compliance statement for Taiwan Additional regulatory information For addit...
Page 135 - Appendix C. WEEE and recycling information; Important information for the European Directive 2002/96/EC; Recycling information; Collecting and recycling a disused Lenovo computer or monitor
Appendix C. WEEE and recycling information Important information for the European Directive 2002/96/EC EU Only The Waste Electrical and Electronic Equipment (WEEE) mark applies only to countries within the EuropeanUnion (EU) and Norway. Appliances are labeled in accordance with European Directive 20...
Page 136 - Recycling information for Brazil; Declarações de Reciclagem no Brasil; Battery recycling information for Taiwan
If you are a company employee and need to dispose of a Lenovo computer or monitor that is the propertyof the company, you must do so in accordance with the Law for Promotion of Effective Utilization ofResources. Computers and monitors are categorized as industrial waste and should be properly dispos...
Page 137 - Battery recycling information for the European Union; This mark applies only to countries within the European Union (EU).
Battery recycling information for the European Union Notice: This mark applies only to countries within the European Union (EU). Batteries or packaging for batteries are labeled in accordance with European Directive 2006/66/ECconcerning batteries and accumulators and waste batteries and accumulators...
Page 139 - Appendix D. ENERGY STAR model information; ENERGY STAR
Appendix D. ENERGY STAR model information ENERGY STAR ® is a joint program of the U.S. Environmental Protection Agency and the U.S. Department of Energy aimed at saving money and protecting the environment through energy efficient products andpractices. Lenovo is proud to offer our customers product...
Page 141 - Appendix E. Ek Bilgiler
Appendix E. Ek Bilgiler 1. İmalatçı ya da ithalatçı firmaya ilişkin bilgiler: Ürünün ithalatçı firması, Lenovo Technology B.V. Merkezi Hollanda Türkiye İstanbul Şubesi’dir. Adresi vetelefonu şöyledir: Uner Plaza Eski Üsküdar YoluErkut Sokak. No: 4 / 1 Kat: 3KozyatağıKadıkoy, İSTANBUL, TürkiyeTel: 90...
Page 143 - Appendix F. Servis istasyonlari; Garanti Hizmetinin Alınabileceği Merkezler; ADANA
Appendix F. Servis istasyonlari Garanti süresi içerisinde müşteri arızalı ürünü aşağıda belirtilen merkezlere teslim ederek garanti hizmetindenyararlanır. Ürün yerinde garanti hizmeti içeriyorsa, bu merkezlerden birine telefon edebilirsiniz. Garanti Hizmetinin Alınabileceği Merkezler ADANA BSD Bilgi...
Page 147 - İZMİR
Novatek Bilgisayar Sistemleri San.ve Tic.Ltd. Şti.Adresi: Raşit Rıza Sokak, Yıldırım İş Hanı, No: 1 Kat: 1Mecidiyeköy İstanbulPosta Kodu: 80300Web Adresi: http://www.novateknoloji.com/Telefon: 212 356 75 77Faks no: 212 356 75 88 Peritus Bilgisayar Sist. Dış Tic.San.Ltd. Şti.Adresi: Ziverbey Eğitim M...
Page 151 - Index
Index A a rescue medium, creating and using 76 accessing system board components and drives 34 Administrator, password 82 antivirus software 7 audio line-in connector 9 audio line-out connector 9 audio subsystem 1 B backup and recovery operations 74 basic troubleshooting 95 boot-block recovery 90 C ...