Lasko X30400 - Manual
Lasko X30400 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – HARDWARE BAG CONTENTS; MOTOR HARDWARE BAG
- Page 4 – GRILL AND BLADE ASSEMBLY; MAKE SURE BOLTS IN COLUMN AND MOTOR ASSEMBLY STEPS
- Page 5 – ALWAYS UNPLUG THE CORD BEFORE MOV-; MAINTENANCE; FAN MAY START UP WHEN INITIALLY PLUGGED IN.
- Page 6 – well as the type and style (located on the underside of your product).
- Page 7 – INCLUIDO CON EL VENTILADOR:; ESTE VENTILADOR NO CUMPLE CON LOS REQUISITOS DEL; CONSERVE ESTAS; LEA Y GUARDE ESTAS INSTRUCCIONES; MANTENIMIENTO AL PRODUCTO DESCRITO.
- Page 8 – BOLSA DE TORNILLERÍA D:; CONTENIDO DE LA BOLSA DE HERRAJES; BOLSA DE TORNILLERÍA A:; BOLSA TORNILLERÍA DE
- Page 9 – MONTAJE DE LA BASE; MONTAJE DE LAS RUEDAS EN LA BASE
- Page 10 – MONTAJE DE ENREJADO Y HÉLICE; MONTAJE DE COLUMNA / MOTOR
- Page 11 – SIEMPRE DESENCHUFE EL CABLE; A D V E R T E N C I A; ¡NO SUMERJA EL VENTILADOR EN
- Page 12 – GARANTÍA LIMITADA DE LASKO PRODUCTS, INC.
30" INDUSTRIAL GRADE OSCILLATING
PEDESTAL FAN WITH WHEELS
Model X30400
Rev. A 10/11
1
5084440
GENERAL SAFETY INFORMATION
1. Read all instructions before using Fan.
2. Make certain that the power source conforms to the electri-
cal requirements of the Fan.
3. Use this Fan only as described in this manual. Any other use not
recommended by the manufacturer may cause fire, electrical
shock, or injury to persons.
4. To reduce the risk of personal injury and electric shock, the
Fan should not be played with or placed where small children
can reach it.
5. Unplug power cord before servicing, or moving the Fan.
WARNING:
DO NOT DEPEND UPON THE ON-OFF SWITCH
AS THE SOLE MEANS OF DISCONNECTING POWER WHEN
INSTALLING OR SERVICING THE FAN. ALWAYS UNPLUG THE
POWER CORD.
6. T h i s F a n m u s t N O T b e u s e d i n p o t e n t i a l l y d a n g e r o u s
locations such as flammable, explosive, chemical-laden
o r w e t a t m o s p h e r e s .
7. DO NOT use Fan in or near a window. Rain may create an
electrical hazard.
8. Completely reassemble Fan, according to instructions,
before reconnecting to power supply.
9. The power cord is equipped with a three-prong grounded
plug that must be inserted into a matching receptacle. Under
no circumstances should the grounding prong be cut off the
plug. Where a two-prong wall receptacle is encountered,
it must be replaced with a properly grounded three-prong
receptacle installed in accordance with the National Electrical
Code (NEC) and all applicable local codes and ordinances.
This work must be done only by a qualified electrician, using
copper wire only.
WARNING:
USE OF A THREE-PRONG TO TWO-PRONG
ADAPTER IS NOT RECOMMENDED. IMPROPER CONNECTION
MAY CREATE THE RISK OF ELECTROCUTION. USE OF SUCH
ADAPTER IS NOT PERMITTED IN CANADA.
10. Where possible, avoid the use of extension cords. If they must
be used, minimize the risk of overheating by ensuring that they
are UL listed. Never use a single extension cord to operate
more than one Fan.
11. NEVER operate any Fan with a damaged cord or plug or after
the Fan malfunctions, has been dropped or damaged in any
manner.
12. Do not insert or allow fingers or foreign objects to enter any
ventilation or exhaust opening as it may cause an electric shock
or fire, or damage the Fan. Do not block or tamper with the Fan
in any manner while it is in operation.
13.Always place the Fan on a stable, flat, level surface when
operating, to avoid the chance of the Fan overturning. Locate
the Power Cord so the Fan or other objects are not resting on it.
Do not run cord under carpeting. Do not cover cord with throw
rugs, runners, or similar coverings. Do not route cord under
furniture or appliances. Arrange cord away from traffic area and
where it will not be tripped over.
14.This Fan is not intended for use in wet or damp locations.
Never locate a Fan where it may fall into a bathtub or other
water container.
15. Do not use Fan outdoors.
16.This Fan is not suitable for use in agricultural facilities including
areas where livestock, poultry or other animals are confined.
Please refer to National Electric Code (NEC) Article 547-7
(2008), or applicable state or local codes or standards relating
to electrical requirements for Agricultural Buildings.
THIS FAN
DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE
547-7 (2008).
17.This Fan is not suitable for use in hazardous locations. Please
refer to National Electric Code (NEC) Article 500 or applicable
state or local codes or standards relating to electrical
requirements for Hazardous locations.
THIS FAN DOES NOT
MEET THE REQUIREMENTS OF NEC ARTICLE 500 (2008).
WARNING:
REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK
– DO NOT USE THIS FAN WITH ANY SOLID STATE SPEED
CONTROL DEVICES.
CAUTION:
BECAUSE OF THE SIZE AND WEIGHT OF THIS
FAN, MAKE SURE ALL PARTS ARE COMPLETELY ASSEMBLED
ACCORDING TO INSTRUCTIONS. FAILURE TO DO SO COULD
RESULT IN FAN COMING APART DURING OPERATION AND/OR
PERSONAL INJURY.
SAVE THESE INSTRUCTIONS
INCLUDED WITH THIS FAN:
(1) 3 Speed, Oscillating Motor Assembly
(1) Column Assembly
(1) Base
(1) Blade
(1) Front Grill
(1) Rear Grill
(1) Hardware Bag
(1) Motor Hardware Bag
(1) Wheel Kit Bag
(1) Instruction Sheet
READ AND SAVE THESE INSTRUCTIONS
READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN THE PRODUCT DESCRIBED.
PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION. FAILURE TO COMPLY WITH
INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE!
RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.
Register Your Product Today
www.laskoproducts.com/registration
You will benefit from:
- efficient and enhanced support
- future product updates
scan with a smart phone
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
HARDWARE BAG D: (1) Left Wheel Assembly (1) Right Wheel Assembly (4) Carriage Bolts (5/16-18 X 1”) (4) Split Lockwashers (5/16”)(4) Hex Nuts (5/16-18) Split Lockwasher (5/16”) Carriage Bolt (5/16-18 X 1”) Hex Nut (5/16-18) Rev. A 10/11 2 5084440 HARDWARE BAG CONTENTS MOTOR HARDWARE BAG (1) Hex Bolt ...
Locate Motor Hardware Bag to Assemble Column and Motor Assembly.1. Place flat section on Upper Tube of Column Assembly next to Neck on Motor Assembly. Align the 1/2” diameter hole in the flat section on the Upper Tube of Column Assembly with the 1/2” diameter hole in the Motor Assembly. (Figure 4) 2...
REPOSITIONING INSTRUCTIONS Rev. A 10/11 5 5084440 1. Disconnect ALL POWER before repositioning Fan. Never move Fan while blade is in motion.2. Make sure Fan Head is secured by tightening 1/2” Hex Bolt and adjustment knob to secure the head assembly.3. Make sure that the oscillation knob in the motor...
