Laney Concept 10 - Manual - manualsarea.com

Page 2 - Concept; Concept Manual; User Manual; TABLE OF CONTENTS

Concept Concept Manual 2 2 Concept 10 + Concept 16 User Manual TABLE OF CONTENTS Page 4 Page 3 Page 2 Contents General Information Concept 10/16 Quick Start Guide Concept 10/16 Quick Start Guide Concept 10/16 Quick Start Guide Concept 10/16 Quick Start Diagrams Concept 10/16 Quick Start Diagrams Con...

Page 3 - UNPACKING

Concept Concept Manual 3 We at Laney are extremely pleased that you have decided to select a Concept product for your mixing and we wish to reinforce your judgement by ensuring you get off to a flying start by including this comprehensive user manual to assist you in getting to know your equipment. ...

Page 4 - Laney; SPECIAL FEATURES

Concept Concept Manual 4 Laney SPECIAL FEATURES Laney have been established in audio amplification for over twenty five years, during which time it has firmly established itself as a benchmark for audio products. Feedback from musicians and recording engineers, supported by original design ingenuity...

Page 8 - Concept 10/16 Quick Set Up Guide; La

Concept Concept Manual 8 Laney Concept 10/16 Quick Set Up Guide O O O O O . O AMP MIKED UP 8dB 8dB 8dB 8dB 4dB 4dB 0dB 0dB 4dB 4dB MON MON STEREO STEREO LEFT LEFT RIGHT RIGHT MICGAIN MICGAIN MONO MONO MIC MIC STEREO STEREO LINE GAIN LINE GAIN MIC MIC GAIN GAIN MIC MIC GAIN GAIN MIC MIC GAIN GAIN MIC...

Page 9 - o o

Concept Concept Manual 9 oo oo O O O O O FX PROCESSOR o o o o o o POWER AMPLIFIER STEREORIGHT DO NOT OBSTRUCT FAN APERTURE DO NOT OBSTRUCT FAN APERTURE DO NOT OBSTRUCT INLET VENTS DO NOT OBSTRUCT INLET VENTS MINIMUM LOAD = 4 OHMS MINIMUM LOAD = 4 OHMS PIN -1GROUND PIN -1GROUND PIN +1 SIGNAL PIN +1 S...

Page 10 - PHANTOM POWER; WARNING

Concept Concept Manual 10 Mic/Line channel 5A) HI 5C) LO 5) EQUALISATION 5C Each mono channel has an 'insert' via a stereo jack socket,wired to the tip send ,ring return convention . Effects units can be inserted here and enter the signal path post 'gain' but pre-eq.Reverbs/compressors feedback elim...

Page 11 - continued

Concept Concept Manual 11 continued Mic/Line channel The Mon control is set for pre-fade operation for use as a monitor send.The signal passes to the feedback filter and monitor fader in the master section before leaving by the jack socket marked Mon. Mon 6) PFL 11) 11) 11 11 GAIN GAIN HI HI MID MID...

Page 12 - LO; ) EQUALISATION; MID

Concept Concept Manual 12 mic/stereo channel 5A) HI 5A) LO 5) EQUALISATION Phantom powering is available to all 'mic' inputs for use with condenser microphones PHANTOM POWER 12)13) 14) 15) Adjusts the level of the Stereo input signal into the channel.It should be set so that the input signal is not ...

Page 14 - AUXILIARY INPUTS

Concept Concept Manual 14 The fader sets the output level of the Auxiliary to be sent to the MASTERS . FADER The Mon control is set for pre-fade operation for use a monitor send.The signal passes to the feedback filter and monitor fader in the master section before leaving by the jack socket marked ...

Page 15 - Auxiliary Outputs; MONITOR TO LEFT AMP

Concept Concept Manual 15 PFL PFL +10 +10 +6 +6 0dB 0dB -6 -6 -10 -10 -20 -20 -30 -30 L R L R TAPEOUT TAPEOUT MON MON AUX 1 AUX 1 TAPE OUTLEVEL TAPE OUTLEVEL AUX 1MASTER SEND AUX 1MASTER SEND HEADPHONES HEADPHONES PFL ACTIVE PFL ACTIVE MON TOLEFT AMP MON TOLEFT AMP FREQ FREQ CUT CUT MONITOR MONITOR ...

Page 17 - REAR PANEL FACILITIES

Concept Concept Manual 17 Line Outs are provided for the connection of additional speaker/power amps,active speakers.The output level signal is controlled by the line out/tape out level control . The signal at these connectors is always the Master L + R. Power connection is provided on a 3 pin IEC m...

Page 19 - FURTHER NOTES