Land Pride 4400NT - Manual
Land Pride 4400NT – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Assembly Instructions; Gearbox Removal
- Page 3 – Preparations for new Gearbox Mount; figure 4
- Page 4 – Gearbox Assembly; Refer to Figure 7 on page 4:; not to drill through the transmission housing.; Lower vehicle to the ground and remove wheel; Gearbox Removal (Muffler Not shown For Clarity)
- Page 5 – Part Description; Listing of Parts
1
© Copyright 2005
Printed
Before You Start
Your Land Pride Retro Fit Gearbox Mount is exclusively
designed for Land Pride 4400NT & 4400ST Trekers.
Please read these installation instructions and the
vehicle Operator’s Manual thoroughly before beginning.
Especially read information relating to safety concerns.
Also included in the Operator’s Manual is important
information on operation, adjustment, troubleshooting,
and maintenance for this attachment (some manual
sections do not apply to all accessories).
A separate Parts Manual for replacement parts can be
purchased from your dealer or downloaded free of
charge from our web site at www.landpride.com. Have
model and serial numbers handy when placing an order.
Manual Part Numbers:
• Operator’s Manual . . . . . . . . . . . . . . . . 700-108M
• Parts Manual . . . . . . . . . . . . . . . . . . . . 700-108P
General Information
These assembly instructions apply to the following Retro
Fit Gearbox Mounting Kits listed below:
700-373A
NT Retro Fit Gearbox Mount
700-374A
ST Retro Fit Gearbox Mount
Tools required:
•
Safety Glasses
•
Work Gloves
•
Center Punch
•
Hammer
•
Drill with 1/8" & 11/32" Drill Bits
•
Torque wrench with required sockets listed below
•
7/16" Socket and box end or open end wrench
•
1/2" Socket and box end or open end wrench
•
9/16" Socket and box end or open end wrench
•
M22 Socket and box end or open end wrench
•
3/16" Hex socket wrench
When you see this symbol, the subsequent
instructions and warnings are serious - follow
without exception. Your life and the lives of
others depend on it!
!
IMPORTANT: Before you begin, read these
instructions and check to be sure all par ts and tools
are accounted for. Please retain these installation
instructions for future reference and par ts ordering
information.
Assembly Instructions
A detailed listing of parts for each accessory kit is
provided on page 5. Use the list that is for your Treker as
a checklist to inventory parts received. Please contact
your local Land Pride dealer for any missing hardware.
Initial Preparations
1.
Park vehicle on a flat surface, move gear shift lever to
forward, set park brake, lock the cargo box in the up
position, turn off engine and remove ignition key.
2.
Chock front and back of front tires to prevent the
vehicle from rolling.
3.
See Operator’s Manual 700-108M for proper jacking
procedures. Follow all safety precautions in the
manual. Jack the back of the vehicle up to remove
pressure on the back right shock.
Refer to Figure 1:
4.
Remove M14 hex nut and hex head cap screw (#1).
Description
Figure 1
Refer to Figure 2:
5.
Rotate shock back to access gearbox components.
Description
Figure 2
1
23676
23677
Treker 4400NT & 4400ST Series
Retro Fit Gearbox Mount
Assembly Instructions
6/14/05
Manual No. 700-372M
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 Manual No. 700-372M 6/14/05 Land Pride Assembly Instructions ■ Gearbox Removal Refer to Figure 3: 1. Remove 3/8" x 4 1/4" lg. upper shock bolt (#6), three3/8" flat washers (#10), two fender washers (#18),one H style motor mounts (# 16), gearbox mountingspacer (#1) and 3/8" hex nut ...
3 6/14/05 Manual No. 700-372M Assembly Instructions Land Pride ■ Preparations for new Gearbox Mount Refer to figure 4: 1. Clamp template plate (#1) to vehicle by aligning thefront edge of template with the front edge of theengine mounting plate. 2. Drill two 1/8" pilot holes in engine plate usin...
4 Manual No. 700-372M 6/14/05 Land Pride Assembly Instructions ■ Gearbox Assembly Refer to Figure 7 on page 4: 1. Assemble right angle gearbox (#12) to mountingbracket (#2) with four 5/16"-18 x 3/4" lg. GR5 hexhead cap screws (#5) and lock washers (#10).Tighten cap screws to 17 ft. lbs. of t...
