Page 2 - Foreword; Welcome; Thank you for using KONICA MINOLTA PageScope Network Setup.; Trademark Acknowledgements; Ethernet is a registered trademark of Xerox Corporation.
i Foreword Welcome Thank you for using KONICA MINOLTA PageScope Network Setup. PageScope Network Setup is utility software which allows simple network setup of devices such as printers. It allows setup of devices on networks connected using TCP/IP or IPX protocol to be handled together. PageScope Ne...
Page 3 - CONTENTS; Installing and Starting PageScope; Displaying Device Output Tray
ii Contents CONTENTS 1 System Requirements ................................ 1 2 Installing and Starting PageScope Network Setup ............................................. 2 2.1 Installing PageScope Network Setup ........... 2 2.2 Starting PageScope Network Setup ............. 2 2.3 Uninstalling P...
Page 5 - Appendix Glossary
iv Contents 6 Option Setup ............................................. 33 6.1 Selecting a Protocol .................................... 33 6.2 Specifying the Search Range ..................... 34 6.3 Specifying BOOTP ....................................... 36 6.4 Specifying Polling Settings .........
Page 6 - System Requirements
1 System Requirements 1 1 System Requirements The following are the minimum system requirements for installing PageScope Network Setup. *(1) We recommend you to use the latest version service packs when using Windows NT 4.0 or Windows 2000. *(2) Although this utility can work without NetWare, it is ...
Page 7 - Installing and Starting PageScope Network Setup; Installing PageScope Network Setup; Starting PageScope Network Setup; Click; Note; Password”
2 Installing and Starting PageScope Network Setup 2 2 Installing and Starting PageScope Network Setup 2.1 Installing PageScope Network Setup Use the following procedure to install PageScope Network Setup.1. Place the CD-ROM into your computer’s CD-ROM drive. 2. Start up the installation program. (se...
Page 8 - Uninstalling PageScope Network Setup
2 Installing and Starting PageScope Network Setup 3 2.3 Uninstalling PageScope Network Setup 2.3.1 For Windows 95/98/Me/NT/2000 1. Click Start → Settings → Control Panel . 2. Double-click the Add/Remove Programs icon. 3. On the Add/Remove Programs Properties dialog box, select KONICA MINOLTA PageSco...
Page 9 - Browsing Network Devices; Screen Configuration; Menu bar; Toolbars
3 Browsing Network Devices 4 3 Browsing Network Devices This section explains the contents of PageScope Network Setup screens. 3.1 Screen Configuration ➀ Menu bar Clicking on a menu pulls it down so you can access its commands. ➁ Toolbar (for the device list) The toolbar provides one-click access to...
Page 10 - ... Displays output tray information for the device selected in the; Device list; This list show devices detected on the network.
3 Browsing Network Devices 5 ... Displays output tray information for the device selected in the device list. ... Quits PageScope Network Setup. ... Displays a dialog box for configuring peer-to-peer printing. ... Refreshes the device list. ... Displays on-line help. ➂ Device list This list show dev...
Page 11 - Device; Specifying Polling Settings; Device Name; Device Search; Option Setup; Status bar
3 Browsing Network Devices 6 Device This is the device icon and device name. The icon that appears differs according to the protocol used for connecting the device. ... Device connected using TCP/IP ... Device connected using IPX Devices connected using both TCP/IP and IPX will be displayed with the...
Page 12 - Statusbars; Browser display area
3 Browsing Network Devices 7 If you cannot see the status bar on the display, select Statusbars on the View menu. ➄ Browser display area This area displays the built-in Web setup page for the device selected in the device list. ➅ Toolbar (for the browser display area) The toolbar contains buttons fo...
Page 13 - Verifying Device Setup Status; Device Property; General; Device Information; NetWare Printing; NetWare Print Setup
3 Browsing Network Devices 8 3.2 Verifying Device Setup Status Verify the current device setup status as follows.1. On the device list, click on the icon for the device whose setup status you want to verify. 2. Select Device Property on the File menu. You could also click the toolbar button. This di...
Page 14 - IP; OK; Displaying the Device Alert Property; Device Alert Property
3 Browsing Network Devices 9 TCP/IP Displays the setup for device TCP/IP. See 4.2 Configuring TCP/ IP for details about changing this setup. 3. After you are finished, click the OK button to close the dialog box. Note 3.3 Displaying the Device Alert Property Follow the procedure described below to d...
Page 15 - Displaying Device Output Tray Information; Select; Device Output Tray Information; on the; File; could also click the toolbar
3 Browsing Network Devices 10 3.4 Displaying Device Output Tray Information Follow the procedure described below to display output tray information for the device selected in the device list. 1. In the device list, click the icon of the device whose output tray information you want to display. 2. Se...
Page 16 - Configuring a Device with PageScope; For printing via a NetWare print server:; Verify the device setup status. See
3 Browsing Network Devices 11 3.5 Configuring a Device with PageScope Network Setup This section describes the procedure for network printer setup with PageScope Network Setup. First check the following points relating to your network environment. Check with your network administrator for details ab...
Page 17 - Changing the Device Setup; Configuring Device Information
4 Changing the Device Setup 12 4 Changing the Device Setup Use the Device Setup dialog to change a device setup. The following are the settings that can be configured when changing a device setup. • Device Information • TCP/IP • NetWare Print 4.1 Configuring Device Information Perform the following ...
Page 18 - You can configure and view the following items on the; Device Model Name; After you are finished making the settings you want, click the; If the settings are correct, click the
4 Changing the Device Setup 13 You can configure and view the following items on the General tab. Device Model Name This is the device model name. You cannot change the device model name here. Device Name This is the device management name. You can type up to 16 characters into the text box to input...
Page 19 - Device Setup; IP Address Setup
4 Changing the Device Setup 14 4.2 Configuring TCP/IP Perform the following steps to configure TCP/IP.1. On the device list, click the icon of the device you want to configure. 2. Select Device Setup on the Setup menu to display the Device Setup dialog box. You could also click the toolbar button. 3...
Page 20 - • Specify an IP address manually
4 Changing the Device Setup 15 • Specify an IP address manually When this option is selected, you can set the IP address manually. Enter the following values.- IP Address Device IP address - Subnet Mask Subnet mask used with the network - Default Gateway Default IP router address for the device RAW ...
Page 21 - NetWare Print Setup; Event Notification
4 Changing the Device Setup 16 4.3 NetWare Print Setup Note Perform the following steps to configure a device for NetWare printing.1. On the device list, click the icon of the device you want to configure. 2. Select Device Setup on the Setup menu to display the Device Setup dialog box. You could als...
Page 22 - Type up to 26 characters into the; Print Server Name; box for the; Print Queue Scan Rate; Specify the Ethernet frame type.; Next
4 Changing the Device Setup 17 4.3.1 Setting up the Print Server Perform the following steps to set up the print server for NetWare printing.1. Type up to 26 characters into the Print Server Name box for the print server name.Normally, you should leave the following items set to their initial defaul...
Page 23 - lator
4 Changing the Device Setup 18 4.3.2 Selecting the Mode Use the procedures in this section to select the server you want to configure as the print server, or the NDS context. If you are using bindery service (NetWare 3.x): 1. Put a check mark into the NetWare 3.x Bindery Server check box. 2. Click t...
Page 24 - Click the; Mode Select; shows a list of NDS contexts for the tree you selected.; When everything is the way you want, click the
4 Changing the Device Setup 19 4. Click the button to display the Mode Select dialog box, which shows a list of NDS contexts for the tree you selected. 5. Select the NDS context to setup the print server, and then click the OK button. 6. When everything is the way you want, click the Next button. No...
Page 25 - To select an existing print queue:; Append; button to add the print queue to the list on; Delete
4 Changing the Device Setup 20 4.3.3 Selecting the Print Queue Use one of the following procedures to select the print queue for the print job. To select an existing print queue: 1. Use the upper left box to select an NDS tree (in the case of NDS) or a server (in the case of bindery service). This d...
Page 26 - To create a new print queue:
4 Changing the Device Setup 21 To create a new print queue: 1. Use the upper left box to select an NDS tree (in the case of NDS) or a server (in the case of bindery service). 2. Click the Create New button to display the Add Queue dialog box. 3. Type up to 26 characters for the name you want to assi...
Page 27 - Selecting Users for Event Notification; button to add the user to the list on the right.; so causes the; PRINT JOB OWNER; icon to appear in the list on the
4 Changing the Device Setup 22 4.3.4 Selecting Users for Event Notification Perform the following steps to select users for notification of events occurring on the device.1. Use the upper left box to select an NDS tree (in the case of NDS) or a server (in the case of bindery service). This displays ...
Page 28 - Back
4 Changing the Device Setup 23 4.3.5 Verifying the Setup The NetWare setup details are displayed in the list. • Click a button on the tree to expand an item. • Click a button on the tree to collapse an item. If you want to change something in the setup, click the Back button to return to the setup s...
Page 29 - A message stating that it is necessary to reset may appear.; Reset Now
4 Changing the Device Setup 24 A message stating that it is necessary to reset may appear. If there are no problems with resetting now, click the Reset Now button.
Page 30 - dialog; P2P Setup; Setup; menu to display the; P2P Setup
5 Peer-to-peer Print Setup 25 5 Peer-to-peer Print Setup Peer-to-peer printing refers to printing directly to a device on the network, without going through the server. Use the P2P Setup dialog box to configure peer-to-peer printing. The information provided here shows setup procedures for the follo...
Page 32 - Specifying the Device Manually; IP Address
5 Peer-to-peer Print Setup 27 5.1.2 Configuring for TCP/IP Peer-to-peer Printing by Specifying the Device Manually Perform the following steps to specify the device manually when configuring for TCP/IP peer-to-peer printing. See 5.1.1 Configuring for TCP/IP Peer-to-peer Printing for the procedure yo...
Page 33 - After Creating the
5 Peer-to-peer Print Setup 28 5. Type the port number for TCP/IP peer-to-peer printing into the Port Number box. 6. Click the Add Port button. Check the details of the setup in the dialog box that appears. 7. If everything is the way you want, click the OK button. 8. When the Success dialog box appe...
Page 35 - up the Print Server; Network Address
5 Peer-to-peer Print Setup 30 5.2.2 Configuring for IPX Peer-to-peer Printing by Specifying the Device Manually Perform the following steps to specify the device manually when configuring for IPX peer-to-peer printing. See 5.2.1 Configuring IPX Peer-to-peer Printing for the procedure you should use ...
Page 36 - Change the port of the existing printer:
5 Peer-to-peer Print Setup 31 5. Click the Add Port button. Check the details of the setup in the dialog box that appears. 6. If everything is the way you want, click the OK button. 7. When the Success dialog box appears, click OK . The P2P Setup dialog box appears. See 5.3 After Creating the Peer-t...
Page 38 - Option Setup; Option; Selecting a Protocol
6 Option Setup 33 6 Option Setup Use the Option dialog box to configure PageScope Network Setup options. The following are the settings that can be configured when changing the option setup. • Protocol (See 6.1 Selecting a Protocol ) • Search Range (See 6.2 Specifying the Search Range ) • Navigation...
Page 39 - Specifying the Search Range
6 Option Setup 34 3. Put a check mark into the box next to option you want to use under Select Protocol . You must select at least one protocol, however both can be selected.Click the Return to standard setting button to return to the protocol to the standard default. 4. Click the OK button. 5. On t...
Page 40 - Specify IP discovery range:
6 Option Setup 35 Specify IP discovery range: Perform the steps below to specify the IP address range for the network where the device is searched for. PageScope Network Setup searches for devices on the broadcast address of the network specified here.a. Type the IP address of the device you want to...
Page 41 - To specify an IP address range for assigning the BOOTP server:
6 Option Setup 36 6.3 Specifying BOOTP Perform the following steps to specify the settings for operation as a BOOTP server.1. Select Option on the Setup menu to display the Option dialog box. 2. Click the BOOTP Setting tab. 3. To operate as a BOOTP server, put a check mark beside Enable BOOTP Server...
Page 43 - Specifying Polling Settings; Polling; To monitor the device status, select; Enable; To quit monitoring the devices, select; Disable
6 Option Setup 38 6.4 Specifying Polling Settings The function for monitoring the device status can be turned on or off, and the interval for polling the devices can be specified. • Polling To monitor the device status, select Enable . To quit monitoring the devices, select Disable . • Polling Inter...
Page 44 - Changing the Password; Type in the current password into the; Password; Type the new password (maximum 16 characters) into the; New; Retype the new password into the; Retype New Password
6 Option Setup 39 6.5 Changing the Password The password used to start up PageScope Network Setup can be changed. 1. Type in the current password into the Password box. 2. Type the new password (maximum 16 characters) into the New Password box. 3. Retype the new password into the Retype New Password...
Page 45 - A protocol used to dynamically allocate IP addresses to the host.
Appendix Glossary 40 Appendix Glossary Bindery service A system used to manage network user information in a database for each server. Mainly, used with NetWare 3.x and earlier. BOOTP A protocol used to automatically allocate TCP/IP parameters (eg. IP address) to the client on the TCP/IP network fro...
Page 46 - NDS
Appendix Glossary 41 NDS A system for managing all network resources in a hierarchical database at a single point. Mainly, used with NetWare 4.x and later. Port number A number used to identify application programs at the data source and destination with the IP connection. RAW port number The number...
