Kohler K-9660-PB- Installation Manual
Kohler K-9660-PB– Installation Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – BC; ABOUT THIS VALVE
- Page 3 – LEVER
- Page 4 – D. Bath Spout with Diverter; Pressure Loop with Bodysprays
- Page 5 – INSTALL VALVE; Secure the water supply piping to the support framing.
- Page 6 – Complete the finished wall.; ADJUST TEMPERATURE SETTINGS; C) water at the mixing valve’s first stop
- Page 8 – Screw
116637-2-
BC
THERMOSTATIC MIXING VALVE TRIM
K-T9493, K-T9494
1. BEFORE YOU BEGIN
IMPORTANT INSTRUCTIONS
READ AND SAVE FOR THE CONSUMER
WARNING: Risk of scalding or other severe injury.
Before completing installation, the installer must set the maximum water temperature setting of this valve to
minimize the risks associated with scalding hazards according to ASTM F 444.
The installer is responsible for installing the valve and adjusting the maximum water temperature of this
thermostatic valve according to instructions.
This valve meets or exceeds ANSI A112.18.1M, ASSE 1016, and CSA B125.
If you do not understand any of the installation or temperature adjustment instructions in this document, in the United
States please contact our Customer Service Department at 1-800-4-KOHLER. Outside the U.S. please contact your
distributor.
IMPORTANT: Please fill in the blanks below and on the valve label. Then insert these instructions into the plastic
bag included with the valve package, and attach the plastic bag to the valve handle for the owner ’s reference.
THIS DEVICE HAS BEEN PRESET BY ______________________ OF
_______________________ TO ENSURE A SAFE MAXIMUM TEMPERATURE.
ANY CHANGE IN THE SETTING MAY RAISE THE DISCHARGE TEMPERATURE
ABOVE THE LIMIT CONSIDERED SAFE, AND LEAD TO SCALDS.
DATE: _____________
CAUTION: Risk of scalding hazard. This device
has been calibrated at the factory to ensure a safe
maximum water temperature. Any variance in
settings or water inlet conditions from those used
during factory calibration may raise the discharge
temperature above the safe limit, and may present a
scalding hazard. Responsibility for installation and
adjustment of this device in accordance with these
instructions lies with the installer.
CAUTION: Risk of product damage. This valve
contains plastic and rubber components. Do not
apply excessive heat to the valve body when you
make solder connections. Do not apply flux or acids
directly to the valve, as damage to the seals, plastic
components, and trim finish may result. Do not apply
petroleum-based lubricants to the valve components,
as damage may result.
TOOLS AND MATERIALS REQUIRED
Thermometer
3/4” nominal copper tubing and fittings
Wrenches
Thin-blade knife or screwdriver
Thread sealant
Solder and flux
Hacksaw or tubing cutter
Silicone Sealant (optional)
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 116637-2- BC Kohler Co., Kohler, WI U.S.A. ABOUT THIS VALVE The thermostatic mixing valve cartridge does notcontain an integral volume control/shut-off valve.You must install a separate volume control/shut-offvalve (K-403) downstream of any valve outlet thatdoes not have an integral shut-off valve...
3 116637-2- BC Kohler Co., Kohler, WI U.S.A. ROUGHING-IN – K-400-K WITH K-T9494-7 Fig. #1 6-1/8” D.(15.6cm) 1-9/16”(4cm)MIN. 2-1/4”(5.7cm) MAX. 4-13/16”(12.2cm) 3-1/16”(7.8cm) ROUGHING-IN – K-401-K WITH K-T9493-4 OR K-T9493-7TRIM Fig. #2 7-1/2”(19.1cm) D. 1-9/16”(4cm) MIN. 2-1/4”(5.7cm) MAX. 4-13/16...
4 116637-2- BC Kohler Co., Kohler, WI U.S.A. 2. COMPOSITE LAYOUT Fig. #3 A. K-400 Thermostatic Mixer and K-T9494 Trim B. K-403 Volume Control and K-T9472 Trim C. K-9663 Twin Ell (For use with Bath Diverter Spout) D. Bath Spout with Diverter E. Fixed Showerhead or Handshower F. K-9660 Vacuum Breaker ...
