Kenwood UBZ-GR14- Manual

3 ENGLISH PREPARATION I N S TA L L I N G / R E M O V I N G T H E B AT T E R I E S This transceiver requires 4 AAA batteries. Use high qualityalkaline batteries to enjoy longer periods of batter y life. 1 If the belt hook is installed, first remove it from thetransceiver (refer to “I NSTALLING / R EM...

4 ENGLISH I N S TA L L I N G / R E M O V I N G T H E B E LT H O O K 1 Align the belt hook tabs with the guides on the rear of thetransceiver. 2 Slide the belt hook down the guides until it locks in place. 3 To remove the belt hook, pull back on the lever on the topof the belt hook and slide the belt...

5 ENGLISH I N S TA L L I N G / R E M O V I N G O P T I O N A L A C C E S S O R I E S Note: Always switch OFF the transceiver power when installing orremoving the optional accessories. The following accessories can be used with this transceiver: • SMC-34 Speaker-Microphone • HMC-3 Headset • EMC-3 Cli...

6 ENGLISH GETTING STARTED 1 S W I T C H I N G T H E P O W E R ON/ OFF To switch the transceiver power ON (or OFF), press andhold the switch for 3 seconds. • A tone sounds to confirm that the power has been switchedON (or OFF). 2 S E L E C T I N G A N O P E R AT I N G M O D E 1 Press and hold the MOD...

7 ENGLISH FRS MODE 1 S E L E C T I N G A C H A N N E L 1 Press the MODE key momentarily. • The FRS and CH icons blink. 2 Press the ▲ or ▼ key to increase or decrease the channel number. • Press and hold the ▲ or ▼ key to continuously increase or decrease the channel number until you release the key....

8 ENGLISH 1 Press the MODE key momentarily, two times. • The FRS and SUB icons blink. 2 Press the ▲ or ▼ key to increase or decrease the code number of the selected channel. • Press and hold the ▲ or ▼ key to continuously increase or decrease the code number until you release the key. 3 Once you hav...

9 ENGLISH 4 C H A N N E L S C A N N I N G 1 When you want to scan all channels for a signal, pressthe MODE key momentarily, three times. • The FRS, CH, and SCAN icons blink and the transceiverscans the channels from channel 1 to 14. • All channel codes are turned off during scan. 2 When a signal is ...

10 ENGLISH FM MODE 1 S E L E C T I N G A S TAT I O N 1 Press the MODE key momentarily. • The FM icon blinks. 2 Press the ▲ or ▼ key to increase or decrease the FM station. 3 Once you have selected your desired station, press thePTT switch. • Pressing the M key after selecting a station will retur n ...

11 ENGLISH FRS/FM MODE 1 S E L E C T I N G A N FRS C H A N N E L Only one FRS station can be monitored while in FRS/FMMode. The channel monitored is the last channel youused while in FRS Mode. To select a channel, you must first enter FRS Mode, thenselect a channel as described in “ 1 Selecting a Ch...

12 ENGLISH 3 S C A N N I N G T H E FM B A N D 1 When you want to scan the FM radio band to find astation, press and hold the ▲ or ▼ key for 0.5 seconds. • The FM and SCAN icons blink and the transceiver scansthe FM radio band. 2 When a station is found, scan will pause at that stationfor 10 seconds....

13 ENGLISH OPERATING FEATURES M O N I T O R I N G A N FRS C H A N N E L When you are not receiving a call, the squelch on thetransceiver automatically mutes the speaker so that you willnot hear very weak signals or background noise.Deactivating this feature to listen to background noise makesadjusti...

14 ENGLISH D I S P L AY I L L U M I N AT I O N 1 To tur n the display backlight ON, press the L keymomentarily. • The display backlight turns ON for 10 seconds. • Each time you press any key other than the PTT switchwhile the display backlight is ON, the 10 second timer willreset, allowing the displ...

15 ENGLISH NOTICES TO THE USER This device complies with Part 15 of the FCC Rules. Operation issubject to the following two conditions: (1) this device may not cause harmful interference, and(2) this device must accept any interference received, includinginterference that may cause undesired operati...

18 ENGLISH B. KENWOOD’S LIABILITY UNDER THIS WARRANTY SHALL BE LIMITED TO THE REPAIR OR REPLACEMENT, AT KENWOOD’SOPTION, OF ANY DEFECTIVE PRODUCT, AND SHALL NOTINCLUDE DAMAGES OF ANY KIND, WHETHER INCIDENTAL,CONSEQUENTIAL OR OTHERWISE. This Warranty is enforceable only in the United States of Americ...

20 ENGLISH Should this unit fail within the warranty period, return it to the originalplace of purchase. When applying for warranty you must present theoriginal copy of your bill of sale as proof of warranty. Upon confirmationby the dealer that the unit has failed as per the terms and conditionsset ...