Kenwood TK-2102G- User Manual

Kenwood TK-2102G

Kenwood TK-2102G– User Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
25 Page 25
26 Page 26
27 Page 27
28 Page 28
29 Page 29
30 Page 30
31 Page 31
32 Page 32
33 Page 33
34 Page 34
35 Page 35
36 Page 36
37 Page 37
38 Page 38
39 Page 39
40 Page 40
41 Page 41
42 Page 42
Page: / 42

Table of Contents:

  • Page 2 – SCOPE OF THIS MANUAL; GENERAL
  • Page 3 – REALIGNMENT; How to Enter Each Mode; Getting Acquainted
  • Page 5 – DISASSEMBLY FOR REPAIR; Removing the case assembly from the chassis; Removing the lever
  • Page 6 – CIRCUIT DESCRIPTION; Frequency Confi guration; Fig. 1 Frequency confi guration
  • Page 7 – PLL Frequency Synthesizer; Fig. 3 AF amplifi er and squelch
  • Page 8 – Fig. 6 Transmit audio and QT/DQT encoder; Fig. 5 Unlock detector circuit
  • Page 9 – ) VCO and RF Amplifi er; ) ANT Switch and LPF; ) Thermal Protection Circuit
  • Page 10 – SEMICONDUCTOR DATA
  • Page 11 – COMPONENTS DESCRIPTION
  • Page 12 – PARTS LIST
  • Page 19 – EXPLODED VIEW; Parts with the exploded numbers larger than 700 are not supplied.
  • Page 20 – PACKING
  • Page 21 – ADJUSTMENT; Test Equipment Required for Alignment; Antenna connector adapter
  • Page 22 – Controls; Frequency; Preparations for tuning the transceiver; Adjustment Frequency; Adjustment Points
  • Page 23 – Transmitter Section
  • Page 25 – Receiver Section
  • Page 26 – PC BOARD
  • Page 30 – SCHEMATIC DIAGRAM
  • Page 33 – Note : The components marked with a dot (
  • Page 34 – BLOCK DIAGRAM
  • Page 36 – LEVEL DIAGRAM
  • Page 37 – OPTIONAL ACCESSORIES
  • Page 38 – SPECIFICATIONS
Loading the manual

SERVICE MANUAL

VHF FM TRANSCEIVER

© 2008-8 PRINTED IN JA PAN
B51-8841-00 (N) 554

TK-2102G

GENERAL ..................................................... 2

SYSTEM SET-UP ......................................... 2

REALIGNMENT ........................................... 3

DISASSEMBLY FOR REPAIR ...................... 5

CIRCUIT DESCRIPTION .............................. 6

SEMICONDUCTOR DATA ......................... 10

COMPONENTS DESCRIPTION ................. 11

PARTS LIST ............................................... 12

EXPLODED VIEW ...................................... 19

PACKING .................................................... 20

ADJUSTMENT .......................................... 21

CONTENTS

PC BOARD

TX-RX UNIT (X57-6020-10) ................. 26

SCHEMATIC DIAGRAM ............................ 30

BLOCK DIAGRAM ..................................... 34

LEVEL DIAGRAM ...................................... 36

OPTIONAL ACCESSORIES

KNB-14 (Ni-Cd BATTERY) .................... 37

KNB-15A (Ni-Cd BATTERY) ................. 37

KNB-20N (Ni-MH BATTERY) ............... 37

SPECIFICATIONS ...................BACK COVER

Knob (CH)
(K29-5278-03)

Knob (VOL)
(K29-5255-03)

Helical antenna
(T90-1036-15)

Plastic cabinet assy
(A02-4049-03)

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Other Manuals for Kenwood TK-2102G

Summary

Page 2 - SCOPE OF THIS MANUAL; GENERAL

TK-2102G 2 INTRODUCTION SCOPE OF THIS MANUAL This manual is intended for use by experienced techni- cians familiar with similar types of commercial grade com-munications equipment. It contains all required service information for the equipment and is current as of the pub-lication date. Changes whic...

Page 3 - REALIGNMENT; How to Enter Each Mode; Getting Acquainted

TK-2102G 3 REALIGNMENT 1. Modes User mode PC mode PC test mode PC tuning mode Data programming mode Mode Function User mode For normal use. PC mode Used for communication between the trans-ceiver and PC. Data programming mode Used to read and write frequency data and other features to and from the t...

Page 5 - DISASSEMBLY FOR REPAIR; Removing the case assembly from the chassis; Removing the lever

TK-2102G 5 DISASSEMBLY FOR REPAIR ■ Removing the case assembly from the chassis 1. Remove the two knobs q , cushion w and three round nuts e . 2. Remove the two screws r . 3. Expand the right and left sides of the bottom of the case assembly, then Iift and remove the chassis from the case assembly t...

Other Kenwood Models